arXiv subjects

Riku Jäntti

Publications and source records attributed to Riku Jäntti.

At least 19 recordsLinked to original sources

arXiv2026

Outage Analysis of Backscatter-Based Ambient IoT Device Classes with Energy Buffering

This paper presents an analytical framework for evaluating the outage probability of ambient Internet of Things (A-IoT) device classes communicating directly with a base station. Device 1 is a passive backscatter device with minimal storage, while Device 2 is equipped with a supercapacitor that enables energy buffering and optional amplification. The proposed framework jointly accounts for carrier-detection sensitivity, energy harvesting constraints, supercapacitor energy dynamics, and an energy-aware amplification policy, while the energy evolution of buffered devices is modeled using a discrete-time Markov chain (DTMC). The results highlight the interplay between energy availability and communication reliability. Device 2 achieves superior performance in energy-rich regimes due to buffering and amplification gains, whereas Device 1 becomes more robust in energy-constrained regimes, particularly at larger distances or under high payload requirements. These findings highlight that the optimal device choice depends critically on the operating regime and application demands.

eess.SP↗

arXiv2026

Ambient IoT Backscatter Devices as Passive Anchors for NLOS Cellular Positioning: Fundamental Limits

Ambient Internet-of-Things backscatter devices at known locations can act as low-cost passive anchors by creating geometrically anchored reflected paths in cellular networks. Unlike reconfigurable intelligent surfaces, practical backscatter devices are independently controlled and lack a common phase reference; their modulation signatures may be known, but their reflection gains and residual phases are generally uncalibrated. We study how much localization information survives this incomplete per-device calibration in uplink non-line-of-sight (NLOS) positioning, where the direct NLOS path and the backscatter-assisted paths share an unknown scatterer. Treating the common channel gain, the relative backscatter response, and the residual device phases as nuisance parameters, we derive closed-form equivalent Fisher information matrices for calibrated, partially calibrated, and fully uncalibrated operation. The analysis shows that unknown device phases remove carrier-phase information from the backscatter-assisted paths, whereas joint uncertainty in the common gain and relative response leaves the direct NLOS path with only bandwidth-dependent delay information. The resulting position-domain bounds show that device count alone is insufficient: the passive anchors must also observe the common scatterer from sufficiently diverse directions. For joint single-snapshot identification of the user equipment and scatterer, at least two devices in two dimensions and three in three dimensions are necessary. The results identify deployment implications for Ambient Internet-of-Things positioning and show which calibration losses also apply to separable subpanel-based reconfigurable-surface architectures.

eess.SP↗

arXiv2026

Joint Visible Light and Backscatter Communications for Proximity-Based Indoor Asset Tracking Enabled by Energy-Neutral Devices

In next-generation wireless systems, providing location-based mobile computing services for energy-neutral devices has become a crucial objective for the provision of sustainable Internet of Things (IoT). Visible light positioning (VLP) has gained great research attention as a complementary method to radio frequency (RF) solutions since it can leverage ubiquitous lighting infrastructure. However, conventional VLP receivers often rely on photodetectors or cameras that are power-hungry, complex, and expensive. To address this challenge, we propose a hybrid indoor asset tracking system that integrates visible light communication (VLC) and backscatter communication (BC) within a simultaneous lightwave information and power transfer (SLIPT) framework. We design a low-complexity and energy-neutral IoT node, namely backscatter device (BD) which harvests energy from light-emitting diode (LED) access points, and then modulates and reflects ambient RF carriers to indicate its location within particular VLC cells. We present a multi-cell VLC deployment with frequency division multiplexing (FDM) method that mitigates interference among LED access points by assigning them distinct frequency pairs based on a four-color map scheduling principle. We develop a lightweight particle filter (PF) tracking algorithm at an edge RF reader, where the fusion of proximity reports and the received backscatter signal strength are employed to track the BD. Experimental results show that this approach achieves the positioning error of 0.318 m at 50th percentile and 0.634 m at 90th percentile, while avoiding the use of complex photodetectors and active RF synthesizing components at the energy-neutral IoT node. By demonstrating robust performance in multiple indoor trajectories, the proposed solution enables scalable, cost-effective, and energy-neutral indoor tracking for pervasive and edge-assisted IoT applications.

eess.SP↗

arXiv2026

Joint Visible Light and RF Backscatter Communications for Ambient IoT Network: Fundamentals, Applications, and Opportunities

The rapid growth of the Internet of Things (IoT) devices in the sixth generation (6G) wireless networks raises significant sustainability and scalability challenges due to energy consumption, deployment complexity, and environmental impact. Ambient IoT (A-IoT), leveraging ambient energy harvesting (EH) for batteryless device operation, has emerged as a promising solution to address these challenges. Among various EH and communication techniques, visible light communication (VLC) integrated with ambient backscatter communication (AmBC) offers remarkable advantages, including energy neutrality, high reliability, and enhanced security. In this article, we propose a joint VLC-AmBC architecture, emphasizing fundamental concepts, system designs, and practical implementations. We explore potential applications in environmental monitoring, healthcare, smart logistics, and secure communications. We present proof-of-concept demonstrations for three distinct types of ambient backscatter devices (AmBDs): EH-Only, VLC-Relay, and VLC-Control. Experimental results demonstrate the feasibility of implementing joint VLC-AmBC systems, highlighting their practical viability across various deployment scenarios. Finally, we outline future research directions, including integrated sensing and communication, as well as optimized energy-efficient deployment. Open issues, such as large-scale deployment challenges, are also discussed, thereby providing a clear roadmap for future developments in joint VLC-AmBC-enabled A-IoT ecosystems.

eess.SY↗

arXiv2026

Backscatter Assisted Indoor NLOS Positioning

Passive backscatter devices (BDs) can enable indoor non-line-of-sight (NLOS) positioning by serving as virtual anchors whose Doppler-separated signatures are observable in standard channel estimates. This paper studies continuous user-equipment (UE) tracking in corridor environments using a noncoherent power-domain formulation that avoids BD phase synchronization and remains robust to residual carrier offsets and strong multipath. The BD-dependent measurements are modeled by a log-distance law with unknown BD-specific offsets, which allows passive asynchronous devices to be used as anchors without transmit-power calibration. Based on this model, we develop a corridor-constrained maximum a posteriori (MAP) tracker with motion regularization and Huber-robust estimation. In ray-tracing-inspired simulations, the method achieves median positioning errors of 0.23--0.27 m with 90th-percentile errors below 0.45 m. In office-corridor measurements with four passive BDs at 866 MHz, it attains an aggregated median error of 0.505 m and outperforms a simple weighted-average baseline. The results show that passive asynchronous BDs can provide practical sub-meter indoor NLOS tracking while remaining compatible with existing channel-estimation pipelines and energy-autonomous BD deployments.

eess.SP↗

arXiv2026

Self-Calibrated Indoor Tracking from Backscatter Fiducials under NLOS Transmitter Illumination

This paper studies indoor tracking from wall-mounted backscatter fiducials in corridor segments outside direct transmitter illumination. In the measured setup, the transmitter-to-fiducial links are NLOS, whereas the fiducial-to-receiver links along the corridor are largely LOS. The main challenge is that the effective fiducial response is deployment-dependent, so a fixed calibrated link budget is not reliable. We therefore use a grid-based penalized-likelihood tracker that profiles the receiver path, a fitted log-distance slope parameter, and fiducial-specific offsets directly from received powers. The resulting paths can then be reused as surrogate calibration coordinates for residual-map correction, while the same correction with measured calibration coordinates is reported only as a reference. On a short four-fiducial corridor segment, the profiled dual-band tracker gives a 0.52 m median error without measured calibration coordinates, and surrogate residual correction improves this to 0.46 m. With measured calibration coordinates, the same correction and a RADAR-style fingerprint reference both reach 0.31 m. The main remaining limitation is therefore the quality of the surrogate calibration paths rather than the structured observation model itself.

eess.SP↗

arXiv2026

Dual-Hop Joint Visible Light and Backscatter Communication Relaying under Finite Blocklength

This paper investigates a dual-hop joint visible light communication (VLC) and backscatter communication (BC) relaying framework under the finite blocklength (FBL) constraint, aiming at energy-neutral Ambient Internet of Things (A-IoT) deployments. In the proposed system, indoor LED access points are used to simultaneously provide illumination and transmit information over light to a backscatter device (BD), which harvests optical energy and backscatters the received messages to user equipments (UEs) equipped with radio frequency (RF) front ends. This forwarding of the information from VLC to RF channels is implemented without the need for carrier synthesizers and power amplifiers at the IoT node. By modeling the end-to-end communication link with short-packet IoT traffic and realistic levels of interference between adjacent VLC coverage areas, we analyze the outage performance and achievable data rate of the proposed system. Simulation results demonstrate that key factors, such as placement and orientation of the BD, as well as the selected code rate of the system affect reliability and data rate that can be achieved for communication purposes. The insights gained from this study pave the way for ambient power-enabled IoT solutions and future hybrid VLC/RF network designs.

eess.SP↗

arXiv2026

AmbShield: Enhancing Physical Layer Security with Ambient Backscatter Devices against Eavesdroppers

Passive eavesdropping compromises confidentiality in wireless networks, especially in resource-constrained environments where heavyweight cryptography is impractical. Physical layer security (PLS) exploits channel randomness and spatial selectivity to confine information to an intended receiver with modest overhead. However, typical PLS techniques, such as using beamforming, artificial noise, and reconfigurable intelligent surfaces, often involve added active power or specialized deployment, and, in many designs, rely on precise time synchronization and perfect CSI estimation, which limits their practicality. To this end, we propose AmbShield, an AmBD-assisted PLS scheme that leverages naturally distributed AmBDs to simultaneously strengthen the legitimate channel and degrade eavesdroppers' without requiring extra transmit power and with minimal deployment overhead. In AmbShield, AmBDs are exploited as friendly jammers that randomly backscatter to create interference at eavesdroppers, and as passive relays that backscatter the desired signal to enhance the capacity of legitimate devices. We further develop a unified analytical framework that analyzes the exact probability density function (PDF) and cumulative distribution function (CDF) of legitimate and eavesdropper signal-to-interference-noise ratio (SINR), and a closed-form secrecy outage probability (SOP). The analysis provides clear design guidelines on various practical system parameters to minimize SOP. Extensive experiments that include Monte Carlo simulations, theoretical derivations, and high-SNR asymptotic analysis demonstrate the security gains of AmbShield across diverse system parameters under imperfect synchronization and CSI estimation.

cs.CR↗

arXiv2025

Physical Layer Security over Fluid Reconfigurable Intelligent Surface-assisted Communication Systems

This letter investigates the secrecy performance of wireless communication systems assisted by a fluid reconfigurable intelligent surface (FRIS). Unlike conventional reconfigurable intelligent surfaces (RISs) with fixed geometries, FRISs dynamically select a subset of reflective elements based on real-time channel conditions, offering enhanced spatial diversity and adaptability. Using this foundation, we model a secure downlink scenario where a base station communicates with a legitimate user in the presence of an eavesdropper, and the propagation is assisted by a FRIS with a limited number of elements set to the ON state. We analyze the system's secrecy performance under spatial correlation by deriving analytical lower and upper bounds for the secrecy outage probability (SOP) and average secrecy capacity (ASC), respectively. Our results demonstrate that FRIS effectively enables secure communication under spatial correlation. Even with partial activation, FRIS significantly outperforms conventional RISs in enhancing secrecy performance under varying deployment densities and element correlations.

cs.IT↗

arXiv2025

Physical Layer Challenge-Response Authentication between Ambient Backscatter Devices

Ambient backscatter communication (AmBC) has become an integral part of ubiquitous Internet of Things (IoT) applications due to its energy-harvesting capabilities and ultra-low-power consumption. However, the open wireless environment exposes AmBC systems to various attacks, and existing authentication methods cannot be implemented between resource-constrained backscatter devices (BDs) due to their high computational demands.To this end, this paper proposes PLCRA-BD, a novel physical layer challenge-response authentication scheme between BDs in AmBC that overcomes BDs' limitations, supports high mobility, and performs robustly against impersonation and wireless attacks. It constructs embedded keys as physical layer fingerprints for lightweight identification and designs a joint transceiver that integrates BDs' backscatter waveform with receiver functionality to mitigate interference from ambient RF signals by exploiting repeated patterns in OFDM symbols. Based on this, a challenge-response authentication procedure is introduced to enable low-complexity fingerprint exchange between two paired BDs leveraging channel coherence, while securing the exchange process using a random number and unpredictable channel fading. Additionally, we optimize the authentication procedure for high-mobility scenarios, completing exchanges within the channel coherence time to minimize the impact of dynamic channel fluctuations. Security analysis confirms its resistance against impersonation, eavesdropping, replay, and counterfeiting attacks. Extensive simulations validate its effectiveness in resource-constrained BDs, demonstrating high authentication accuracy across diverse channel conditions, robustness against multiple wireless attacks, and superior efficiency compared to traditional authentication schemes.

cs.CR↗

arXiv2025

Voltage Profile-Driven Physical Layer Authentication for RIS-aided Backscattering Tag-to-Tag Networks

Backscattering tag-to-tag networks (BTTNs) are emerging passive radio frequency identification (RFID) systems that facilitate direct communication between tags using an external RF field and play a pivotal role in ubiquitous Internet of Things (IoT) applications. Despite their potential, BTTNs face significant security vulnerabilities, which remain their primary concern to enable reliable communication. Existing authentication schemes in backscatter communication (BC) systems, which mainly focus on tag-to-reader or reader-to-tag scenarios, are unsuitable for BTTNs due to the ultra-low power constraints and limited computational capabilities of the tags, leaving the challenge of secure tag-to-tag authentication largely unexplored. To bridge this gap, this paper proposes a physical layer authentication (PLA) scheme, where a Talker tag (TT) and a Listener tag (LT) can authenticate each other in the presence of an adversary, only leveraging the unique output voltage profile of the energy harvesting and the envelope detector circuits embedded in their power and demodulation units. This allows for efficient authentication of BTTN tags without additional computational overhead. In addition, since the low spectral efficiency and limited coverage range in BTTNs hinder PLA performance, we propose integrating an indoor reconfigurable intelligent surface (RIS) into the system to enhance authentication accuracy and enable successful authentication over longer distances. Security analysis and simulation results indicate that our scheme is robust against various attack vectors and achieves acceptable performance across various experimental settings. Additionally, the results indicate that using RIS significantly enhances PLA performance in terms of accuracy and robustness, especially at longer distances compared to traditional BTTN scenarios without RIS.

cs.CR↗

arXiv2025

Ambient Backscatter Communication in LTE Uplink Sounding Reference Signal

Ambient Internet of Things (AIoT), recently standardized by the 3rd Generation Partnership Project (3GPP), demands a low-power wide-area communication solution that operates several orders of magnitude below the power requirements of existing 3GPP specifications. Ambient backscatter communication (AmBC) is considered as a competitive potential technique by harvesting energy from the ambient RF signal. This paper considers a symbiotic AmBC into Long Term Evolution (LTE) cellular system uplink. Leveraging by LTE uplink channel estimation ability, AIoT conveys its own message to Base Station (BS) by modulating backscatter path. We explore the detector design, analyze the error performance of the proposed scheme, provide exact expression and its Guassian approximation for the error probability. We corroborate the receiver error performance by Monte Carlo simulation. Analysis of communication range reveals AmBC achieves a reasonable BER of order of magnitude $10^{-2}$ within four times wavelength reading distance. In addition, a AmBC prototype in LTE uplink confirms the its feasibility. The over-the-air experiment results validate theoretical analysis. Hence, the proposed AmBC approach enables AIoT deployment with minimal changes to the LTE system.

eess.SP↗

arXiv2024

Generative AI for Immersive Communication: The Next Frontier in Internet-of-Senses Through 6G

Over the past two decades, the Internet-of-Things (IoT) has become a transformative concept, and as we approach 2030, a new paradigm known as the Internet of Senses (IoS) is emerging. Unlike conventional Virtual Reality (VR), IoS seeks to provide multi-sensory experiences, acknowledging that in our physical reality, our perception extends far beyond just sight and sound; it encompasses a range of senses. This article explores the existing technologies driving immersive multi-sensory media, delving into their capabilities and potential applications. This exploration includes a comparative analysis between conventional immersive media streaming and a proposed use case that leverages semantic communication empowered by generative Artificial Intelligence (AI). The focal point of this analysis is the substantial reduction in bandwidth consumption by 99.93% in the proposed scheme. Through this comparison, we aim to underscore the practical applications of generative AI for immersive media. Concurrently addressing major challenges in this field, such as temporal synchronization of multiple media, ensuring high throughput, minimizing the End-to-End (E2E) latency, and robustness to low bandwidth while outlining future trajectories.

cs.CL↗

arXiv2024

Thin Film Reconfigurable Intelligent Surface for Harmonic Beam Steering

This letter explores an implementation of a novel thin film 1-by-4 reconfigurable intelligent surface (RIS) designed for future communication and sensing scenarios. Utilizing cost-effective inkjet printing methods and additive manufacturing, our approach significantly simplifies the RIS construction process and reduces production costs. The RIS, fabricated on a flexible and lightweight polyethylene terephthalate (PET) substrate, integrates antennas, switching circuitry, and a microcontroller unit (MCU), without a ground shield. This setup enables individual and simultaneous control of each RIS element, manipulating the captured carrier signal by reflecting and refracting its dominant harmonics. Beams of the harmonics can be steered to multiple desired directions at both front and back sides of the surface. Measurement results of the beam steering show that the RIS has the potential to enable RIS-aided communication and sensing applications.

eess.SP↗

arXiv2024

Zero-energy Devices for 6G: Technical Enablers at a Glance

Low-cost, resource-constrained, maintenance-free, and energy-harvesting (EH) Internet of Things (IoT) devices, referred to as zero-energy devices (ZEDs), are rapidly attracting attention from industry and academia due to their myriad of applications. To date, such devices remain primarily unsupported by modern IoT connectivity solutions due to their intrinsic fabrication, hardware, deployment, and operation limitations, while lacking clarity on their key technical enablers and prospects. Herein, we address this by discussing the main characteristics and enabling technologies of ZEDs within the next generation of mobile networks, specifically focusing on unconventional EH sources, multi-source EH, power management, energy storage solutions, manufacturing material and practices, backscattering, and low-complexity receivers. Moreover, we highlight the need for lightweight and energy-aware computing, communication, and scheduling protocols, while discussing potential approaches related to TinyML, duty cycling, and infrastructure enablers like radio frequency wireless power transfer and wake-up protocols. Challenging aspects and open research directions are identified and discussed in all the cases. Finally, we showcase an experimental ZED proof-of-concept related to ambient cellular backscattering.

eess.SP↗

arXiv2024

Joint 3D User and 6D Hybrid Reconfigurable Intelligent Surface Localization

The latest assessments of the emerging technologies for reconfigurable intelligent surfaces (RISs) have indicated the concept's significant potential for localization and sensing, either as individual or simultaneously realized tasks. However, in the vast majority of those studies, the RIS state (i.e., its position and rotation angles) is required to be known a priori. In this paper, we address the problem of the joint three-dimensional (3D) localization of a hybrid RIS (HRIS) and a user. The most cost- and power-efficient hybrid version of an RIS is equipped with a single reception radio-frequency chain and meta-atoms capable of simultaneous reconfigurable reflection and sensing. This dual functionality is controlled by adjustable power splitters embedded at each hybrid meta-atom. Focusing on a downlink scenario where a multi-antenna base station transmits multicarrier signals to a user via an HRIS, we propose a multistage approach to jointly estimate the metasurface's 3D position and 3D rotation matrix (i.e., 6D parameter estimation) as well as the user's 3D position. Our simulation results verify the validity of the proposed estimator via extensive comparisons of the root-mean-square error of the state estimations with the Cramér-Rao lower bound (CRB), which is analytically derived. Furthermore, it is showcased that there exists an optimal hybrid reconfigurable intelligent surface (HRIS) power splitting ratio for the desired multi-parameter estimation problem. We also study the robustness of the proposed method in the presence of scattering points in the wireless propagation environment.

cs.IT↗

arXiv2023

Fault-tolerant one-way noiseless amplification for microwave bosonic quantum information processing

Microwave quantum information networks require reliable transmission of single photon propagating modes over lossy channels. In this article we propose a microwave noise-less linear amplifier (NLA) suitable to circumvent the losses incurred by a flying photon undergoing an amplitude damping channel (ADC). The proposed model is constructed by engineering a simple one-dimensional four node cluster state. Contrary to conventional NLAs based on quantum scissors (QS), single photon amplification is realized without the need for photon number resolving detectors (PNRDs). Entanglement between nodes comprising the device's cluster is achieved by means of a controlled phase gate (CPHASE). Furthermore, photon measurements are implemented by quantum non demolition detectors (QNDs), which are currently available as a part of circuit quantum electrodynamics (cQED) toolbox. We analyze the performance of our device practically by considering detection inefficiency and dark count probability. We further examine the potential usage of our device in low power quantum sensing applications and remote secret key generation (SKG). Specifically, we demonstrate the device's ability to prepare loss-free resources offline, and its capacity to overcome the repeater-less bound of SKG. We compare the performance of our device against a QS-NLA for the aforementioned applications, and highlight explicitly the operating conditions under which our device can outperform a QS-NLA. The proposed device is also suitable for applications in the optical domain.

quant-ph↗

arXiv2023

RIS Position and Orientation Estimation via Multi-Carrier Transmissions and Multiple Receivers

Reconfigurable intelligent surfaces (RISs) are considered as an enabling technology for the upcoming sixth generation of wireless systems, exhibiting significant potential for radio localization and sensing. An RIS is usually treated as an anchor point with known position and orientation when deployed to offer user localization. However, it can also be attached to a user to enable its localization in a semi-passive manner. In this paper, we consider a static user equipped with an RIS and study the RIS localization problem (i.e., joint three-dimensional position and orientation estimation), when operating in a system comprising a single-antenna transmitter and multiple synchronized single-antenna receivers with known locations. We present a multi-stage estimator using time-of-arrival and spatial frequency measurements, and derive the Cramér-Rao lower bounds for the estimated parameters to validate the estimator's performance. Our simulation results demonstrate the efficiency of the proposed RIS state estimation approach under various system operation parameters.

eess.SP↗