arXiv subjects

Roland Sipos

Publications and source records attributed to Roland Sipos.

5 recordsLinked to original sources

arXiv2022

The FASER Detector

FASER, the ForwArd Search ExpeRiment, is an experiment dedicated to searching for light, extremely weakly-interacting particles at CERN's Large Hadron Collider (LHC). Such particles may be produced in the very forward direction of the LHC's high-energy collisions and then decay to visible particles inside the FASER detector, which is placed 480 m downstream of the ATLAS interaction point, aligned with the beam collisions axis. FASER also includes a sub-detector, FASER$ν$, designed to detect neutrinos produced in the LHC collisions and to study their properties. In this paper, each component of the FASER detector is described in detail, as well as the installation of the experiment system and its commissioning using cosmic-rays collected in September 2021 and during the LHC pilot beam test carried out in October 2021. FASER will start taking LHC collision data in 2022, and will run throughout LHC Run 3.

physics.ins-det↗

arXiv2022

The trigger and data acquisition system of the FASER experiment

The FASER experiment is a new small and inexpensive experiment that is placed 480 meters downstream of the ATLAS experiment at the CERN LHC. FASER is designed to capture decays of new long-lived particles, produced outside of the ATLAS detector acceptance. These rare particles can decay in the FASER detector together with about 500-1000 Hz of other particles originating from the ATLAS interaction point. A very high efficiency trigger and data acquisition system is required to ensure that the physics events of interest will be recorded. This paper describes the trigger and data acquisition system of the FASER experiment and presents performance results of the system acquired during initial commissioning.

physics.ins-det↗

arXiv2020

Experience and performance of persistent memory for the DUNE data acquisition system

Emerging high-performance storage technologies are opening up the possibility of designing new distributed data acquisition system architectures, in which the live acquisition of data and their processing are decoupled through a storage element. An example of these technologies is 3DXPoint, which promises to fill the gap between memory and traditional storage and offers unprecedented high throughput for data persistency. In this paper, we characterize the performance of persistent memory devices, which use the 3DXPoint technology, in the context of the data acquisition system for one large Particle Physics experiment, DUNE. This experiment must be capable of storing, upon a specific signal, incoming data for up to 100 seconds, with a throughput of 1.5 TB/s, for an aggregate size of 150 TB. The modular nature of the apparatus allows splitting the problem into 150 identical units operating in parallel, each at 10 GB/s. The target is to be able to dedicate a single CPU to each of those units for data acquisition and storage.

physics.ins-det↗

arXiv2018

The DAQ for the Single Phase DUNE Prototype at CERN

DUNE will be the world's largest neutrino experiment due to take data in 2025. Here is described the data acquisition (DAQ) system for one of its prototypes - ProtoDUNE-SP due to take data in Q4 of 2018. ProtoDUNE-SP also breaks records as the largest beam test experiment yet constructed, and is a fundamental element of CERN's Neutrino Platform. This renders ProtoDUNE-SP an experiment in its own right and the design and construction have been chosen to meet this scale. Due to the aggressive timescale, off-the-shelf electronics have been chosen to meet the demands of the experiment where possible. The ProtoDUNE-SP cryostat comprises two primary subdetectors - a single phase liquid Argon TPC and a companion Photon Detector. The TPC has two candidate readout solutions under test in ProtoDUNE-SP - RCE (ATCA-based) and FELIX (PCIe-based). Fermilab's artDAQ is used as the dataflow software for the experiment. Custom timing and trigger electronics and software are also described. Compression and triggering will take the ~480 Gb/s of data from the front-end and reduce it sufficiently to 20 Gb/s bandwidth to permanent data storage in CERN's EOS infrastructure.

physics.ins-det↗

arXiv2018

FELIX based readout of the Single-Phase ProtoDUNE detector

Large liquid argon Time Projection Chambers have been adopted for the DUNE experiment's far detector, which will be composed of four 17 kton detectors situated 1.5 km underground at the Sanford Underground Research Facility. This represents a large increase in scale compared to existing experiments. Both single- and dual-phase technologies will be validated at CERN, in cryostats capable of accommodating full-size detector modules, and exposed to low-energy charged particle beams. This programme, called ProtoDUNE, also allows for extensive tests of data acquisition strategies. The Front-End LInk eXchange (FELIX) readout system was initially developed within the ATLAS collaboration and is based on custom FPGA-based PCIe I/O cards, connected through point-to-point links to the detector front-end and hosted in commodity servers. FELIX will be used in the single-phase ProtoDUNE setup to read the data coming from 2560 anode wires organized in a single Anode Plane Assembly structure. With a continuous readout at a sampling rate of 2 MHz, the system must deal with an input rate of 96 Gb/s. An external trigger will preselect time windows of 5 ms with interesting activity expected inside the detector. Event building will occur for triggered events, at a target rate of 25 Hz; the readout system will form fragments from the data samples matching the time window, carry out lossless compression, and forward the data to event building nodes over 10 Gb/s Ethernet. This paper discusses the design and implementation of this readout system as well as first operational experience.

physics.ins-det↗