arXiv subjects

Ross Cheriton

Publications and source records attributed to Ross Cheriton.

17 recordsLinked to original sources

arXiv2024

Performance estimation of photonic integrated wavefront corrector for single-mode fiber coupling

Many modern astronomical instruments rely on the optimal coupling of starlight into single-mode fibers (SMFs). For ground-based telescopes, this coupling is limited by atmospheric turbulence. We propose an integrated wavefront corrector based on silicon-on-insulator (SOI) photonics, which samples the aberrated wavefront via a microlens array (MLA). The MLA focuses the sampled wavefront onto an array of grating couplers that inject the beamlets into the single-mode waveguides of the corrector. The beams in each waveguide are then shifted in phase using thermo-optic phase shifters before combining the co-phased beams into one single-mode waveguide. In this work, we analyze the external factors that we anticipate will impact the performance of the corrector. Specifically, we study the effects of the telescope pupil function with obscuration, determine whether the corrector requires tip/tilt pre-correction, and analyze the impact of scintillation on the correction quality.

astro-ph.IM↗

arXiv2024

Experimental demonstration of photonic phase correctors based on grating coupler arrays and thermo-optic shifters

In ground-based astronomy, the ability to couple light into single-mode fibers (SMFs) is limited by atmospheric turbulence, which prohibits the use of many astrophotonic instruments. We propose a silicon-on-insulator photonic chip capable of coherently coupling the out-of-phase beamlets from the subapertures of a telescope pupil into an SMF. The photonic integrated circuit (PIC) consists of an array of grating couplers that are used to inject light from free space into single-mode waveguides on the chip. Metallic heaters modulate the refractive index of a coiled section of the waveguides, facilitating the co-phasing of the propagating modes. The phased beamlets can then be coherently combined to efficiently deliver the light to an output SMF. In an adaptive optics (AO) system, the phase corrector acts as a deformable mirror (DM) commanded by a controller that takes phase measurements from a wavefront sensor (WFS). We present experimental results for the PIC tested on an AO testbed and compare the performance to simulations.

astro-ph.IM↗

arXiv2024

TESERACT: Twin Earth SEnsoR Astrophotonic CubesaT

In this paper, we evaluate the viability of CubeSats as an attractive platform for lightweight instrumentation by describing a proof of concept CubeSat that houses an astrophotonic chip for transit spectroscopy-based exoplanet atmosphere gas sensing. The Twin Earth SEnsoR Astrophotonic CubesaT (TESERACT) was designed to house a correlation spectroscopy chip along with an electrical and optical system for operation. We investigate design challenges and considerations in incorporating astrophotonic instrumentation such as component integration, thermal management and optical alignment. This work aims to be a pathfinder for demonstrating that astrophotonic-based CubeSat missions can perform leading edge, targeted science in lower-cost CubeSat platforms.

astro-ph.IM↗

arXiv2024

Integrated astrophotonic phase control for high resolution optical interferometry

Long baseline optical interferometry and aperture synthesis using ground-based telescopes can enable unprecedented angular resolution astronomy in the optical domain. However, atmospheric turbulence leads to large, dynamic phase errors between participating apertures that limit fringe visibility using telescopes arrays or subaperture configurations in a single large telescope. Diffraction limited optics or adaptive optics can be used to ensure coherence at each aperture, but correlating the phase between apertures requires high speed, high stroke phase correction and recombination that is extremely challenging and costly. As a solution, we show an alternative phase correction and beam combination method using a centimeter-scale silicon astrophotonic chip optimized for H-band operation. The 4.7x10mm silicon photonic chip is fabricated using electron beam lithography with devices with 2 up to 32 independent channels. Light is coupled into the chip using single mode fiber ribbons. An array of microheaters is used to individually tune the effective index of each spiral delay waveguides. Narrowband spectral splitters at each spatial channel divert a modulated digital reference signal from an artificial guide star off-chip for phase measurement. Science light from other wavelengths is coherently combined using on-chip beam combiners and outputted to a single waveguide. We described the role, design, fabrication and characterization of the photonic chip. This photonic phase control scheme can be applied in astronomical interferometry or optical satellite communications.

astro-ph.IM↗

arXiv2024

End-to-end simulations of photonic phase correctors for adaptive optics systems

Optical beams and starlight distorted by atmospheric turbulence can be corrected with adaptive optics systems to enable efficient coupling into single-mode fibers. Deformable mirrors, used to flatten the wavefront in astronomical telescopes, are costly, sensitive, and complex mechanical components that require careful calibration to enable high-quality imaging in astronomy, microscopy, and vision science. They are also impractical to deploy in large numbers for non-imaging applications like free-space optical communication. Here, we propose a photonic integrated c rcuit capable of spatially sampling the wavefront collected by the telescope and co-phasing the subapertures to maximize the flux delivered to an output single-mode fiber as the integrated photonic implementation of a deformable mirror. We present the results of end-to-end simulations to quantify the performance of the proposed photonic solution under varying atmospheric conditions toward realizing an adaptive optics system without a deformable mirror for free-space optical receivers.

physics.optics↗

arXiv2024

Laser driven miniature diamond implant for wireless retinal prostheses

The design and benchtop operation of a wireless miniature epiretinal stimulator implant is reported. The implant is optically powered and controlled using safe illumination at near-infrared wavelengths. An application-specific integrated circuit (ASIC) hosting a digital control unit is used to control the implant's electrodes. The ASIC is powered using an advanced photovoltaic (PV) cell and programmed using a single photodiode. Diamond packaging technology is utilized to achieve high-density integration of the implant optoelectronic circuitry, as well as individual connections between a stimulator chip and 256 electrodes, within a 4.6 mm x 3.7 mm x 0.9 mm implant package. An ultrahigh efficiency PV cell with a monochromatic power conversion efficiency of 55% is used to power the implant. On-board photodetection circuity with a bandwidth of 3.7 MHz is used for forward data telemetry of stimulation parameters. In comparison to implants which utilize inductively coupled coils, laser power delivery enables a high degree of miniaturization and lower surgical complexity. The device presented combines the benefits of implant miniaturization and a flexible stimulation strategy provided by a dedicated stimulator chip. This development provides a route to fully wireless miniaturized minimally invasive implants with sophisticated functionalities.

eess.SP↗

arXiv2023

2023 Astrophotonics Roadmap: pathways to realizing multi-functional integrated astrophotonic instruments

Photonics offer numerous functionalities that can be used to realize astrophotonic instruments. The most spectacular example to date is the ESO Gravity instrument at the Very Large Telescope in Chile. Integrated astrophotonic devices stand to offer critical advantages for instrument development, including extreme miniaturization, as well as integration, superior thermal and mechanical stabilization owing to the small footprint, and high replicability offering cost savings. Numerous astrophotonic technologies have been developed to address shortcomings of conventional instruments to date, including for example the development of photonic lanterns, complex aperiodic fiber Bragg gratings, complex beam combiners to enable long baseline interferometry, and laser frequency combs for high precision spectral calibration of spectrometers. Despite these successes, the facility implementation of photonic solutions in astronomical instrumentation is currently limited because of (1) low throughputs from coupling to fibers, coupling fibers to chips, propagation and bend losses, device losses, etc, (2) difficulties with scaling to large channel count devices needed for large bandwidths and high resolutions, and (3) efficient integration of photonics with detectors, to name a few. In this roadmap, we identify 24 areas that need further development. We outline the challenges and advances needed across those areas covering design tools, simulation capabilities, fabrication processes, the need for entirely new components, integration and hybridization and the characterization of devices. To realize these advances the astrophotonics community will have to work cooperatively with industrial partners who have more advanced manufacturing capabilities. With the advances described herein, multi-functional instruments will be realized leading to novel observing capabilities for both ground and space platforms.

astro-ph.IM↗

arXiv2023

Measurement Accuracy in Silicon Photonic Ring Resonator Thermometers: Identifying and Mitigating Intrinsic Impairments

Silicon photonic ring resonator thermometers have been shown to provide temperature measurements with a 10 mK accuracy. In this work we identify and quantify the intrinsic on-chip impairments that may limit further improvement in temperature measurement accuracy. The impairments arise from optically induced changes in the waveguide effective index, and from back-reflections and scattering at defects and interfaces inside the ring cavity and along the path between light source and detector. These impairments are characterized for 220 x 500 nm Si waveguide rings by experimental measurement in a calibrated temperature bath and by phenomenological models of ring response. At different optical power levels both positive and negative light induced resonance shifts are observed. For a ring with L = 100 um cavity length, the self-heating induced resonance red shift can alter the temperature reading by 200 mK at 1 mW incident power, while a small blue shift is observed below 100 uW. The effect of self-heating is shown to be effectively suppressed by choosing longer ring cavities. Scattering and back-reflections often produce split and distorted resonance line shapes. Although these distortions can vary with resonance order, they are almost completely invariant with temperature for a given resonance and do not lead to measurement errors in themselves. The effect of line shape distortions can largely be mitigated by tracking only selected resonance orders with negligible shape distortion, and by measuring the resonance minimum wavelength directly, rather than attempting to fit the entire resonance line shape. The results demonstrate the temperature error due to these impairments can be limited to below the 3 mK level through appropriate design choices and measurement procedures.

physics.optics↗

arXiv2023

Reinforcement Learning-based Wavefront Sensorless Adaptive Optics Approaches for Satellite-to-Ground Laser Communication

Optical satellite-to-ground communication (OSGC) has the potential to improve access to fast and affordable Internet in remote regions. Atmospheric turbulence, however, distorts the optical beam, eroding the data rate potential when coupling into single-mode fibers. Traditional adaptive optics (AO) systems use a wavefront sensor to improve fiber coupling. This leads to higher system size, cost and complexity, consumes a fraction of the incident beam and introduces latency, making OSGC for internet service impractical. We propose the use of reinforcement learning (RL) to reduce the latency, size and cost of the system by up to $30-40\%$ by learning a control policy through interactions with a low-cost quadrant photodiode rather than a wavefront phase profiling camera. We develop and share an AO RL environment that provides a standardized platform to develop and evaluate RL based on the Strehl ratio, which is correlated to fiber-coupling performance. Our empirical analysis finds that Proximal Policy Optimization (PPO) outperforms Soft-Actor-Critic and Deep Deterministic Policy Gradient. PPO converges to within $86\%$ of the maximum reward obtained by an idealized Shack-Hartmann sensor after training of 250 episodes, indicating the potential of RL to enable efficient wavefront sensorless OSGC.

cs.LG↗

arXiv2022

Astrophotonic Solutions for Spectral Cross-Correlation Techniques

Using photonic devices, we developed a new approach to traditional spectroscopy where the spectral cross-correlation with a template spectrum can be done entirely on-device. By creating photonic devices with a carefully designed, modulated transmission spectrum, the cross-correlation can be carried out optically without requiring any dispersion, vastly simplifying the instrument and reducing its cost. The measured correlation lag can be used for detecting atomic/molecular species within and determining the radial velocity of a particular astrophysical object. We present an overview of two design approaches that are currently being developed that use different photonic platforms: silicon and fibre-based photonics. The silicon photonic approach utilizes ring resonators that can be thermo-optically modulated to carry out the cross-correlation. The fibre approach uses customized fibre Bragg gratings (FBGs) with transmission spectra that can be strain-modulated. Both approaches have been able to detect molecular gas in a lab setting, and we are now in the process of on-sky testing. Lastly, we discuss the future for these types of devices as their simplicity opens up the possibility of developing low-cost, purpose-built multi-object or integral field spectroscopic instruments that could make significant contributions to scientific programs requiring stellar RV measurements and exoplanet detections.

astro-ph.IM↗

arXiv2022

Athermal and tunable echelle grating wavelength demultiplexers using a Mach-Zehnder interferometer launch structure

We present a comparative experimental study of three silicon photonic echelle grating demultiplexers that are integrated with a Mach-Zehnder interferometer (MZI) launch structure. By appropriate choice of the MZI configuration, the temperature induced shift of the demultiplexer channel wavelengths can be suppressed (athermal) or enhanced (super-thermal), or be controlled by an on-chip micro-heater. The latter two configurations allow the channel wavelengths to be actively tuned using lower power than possible by temperature tuning a conventional echelle demultiplexer. In the athermal configuration, the measured channel spectral shift is reduced to less than 10 pm/C, compared to the 83 pm/C shift for an unmodified echelle device. In super-thermal operation an enhanced channel temperature tuning rate of 170 pm/C is achieved. Finally, by modulating the MZI phase with an on-chip heater, the demultiplexer channels can be actively tuned to correct for ambient temperature fluctuations up to 20 C, using a drive current of less than 20 mA.

physics.optics↗

arXiv2021

Fibre Fabry-Pérot Astrophotonic Correlation Spectroscopy for Remote Gas Identification and Radial Velocity Measurements

We present a novel remote gas detection and identification technique based on correlation spectroscopy with a piezoelectric tunable fibre-optic Fabry-Pérot filter. We show that the spectral correlation amplitude between the filter transmission window and gas absorption features is related to the gas absorption optical depth, and that different gases can be distinguished from one another using their correlation signal phase. Using an observed telluric-corrected, high-resolution near-infrared spectrum of Venus, we show via simulation that the Doppler shift of gases lines can be extracted from the phase of the lock-in signal using low-cost, compact, and lightweight fibre-optic components with lock-in amplification to improve the signal-to-noise ratio. This correlation spectroscopy technique has applications in the detection and radial velocity determination of faint spectral features in astronomy and remote sensing. We experimentally demonstrate remote CO2 detection system using a lock-in amplifier, fibre-optic Fabry-Pérot filter, and single channel photodiode.

astro-ph.IM↗

arXiv2020

Spectrum-free integrated photonic remote molecular identification and sensing

Absorption spectroscopy is widely used in sensing and astronomy to understand molecular compositions on microscopic to cosmological scales. However, typical dispersive spectroscopic techniques require multichannel detection, fundamentally limiting the ability to detect extremely weak signals when compared to direct photometric methods. We report the realization of direct spectral molecular detection using a silicon nanophotonic waveguide resonator, obviating dispersive spectral acquisition. We use a thermally tunable silicon ring resonator with a transmission spectrum matched and cross-correlated to the quasi-periodic vibronic absorption lines of hydrogen cyanide. We show that the correlation peak amplitude is proportional to the number of overlapping ring resonances and gas lines, and that molecular specificity is obtained from the phase of the correlation signal in a single detection channel. Our results demonstrate on-chip correlation spectroscopy that is less restricted by the signal-to-noise penalty of other spectroscopic approaches, enabling the detection of faint spectral signatures.

physics.ins-det↗

arXiv2020

Design of Compact and Efficient Silicon Photonic Micro Antennas with Perfectly Vertical Emission

Compact and efficient optical antennas are fundamental components for many applications, including high-density fiber-chip coupling and optical phased arrays. Here we present the design of grating-based micro-antennas with perfectly vertical emission in the 300-nm silicon-on-insulator platform. We leverage a methodology combining adjoint optimization and machine learning dimensionality reduction to efficiently map the multiparameter design space of the antennas, analyse a large number of relevant performance metrics, carry out the required multi-objective optimization, and discover high performance designs. Using a one-step apodized grating we achieve a vertical upward diffraction efficiency of almost 92% with a 3.6 μm-long antenna. When coupled with an ultra-high numerical aperture fiber, the antenna exhibits a coupling efficiency of more than 81% (-0.9 dB) and a 1-dB bandwidth of almost 158 nm. The reflection generated by the perfectly vertical antenna is smaller than -20 dB on a 200-nm bandwidth centered at λ = 1550 nm.

physics.optics↗

arXiv2020

Two-Photon Photocurrent in InGaN/GaN Nanowire Intermediate Band Solar Cells

Intermediate band solar cells hold the promise of ultrahigh power conversion efficiencies using a single semiconductor junction. Many current implementations use materials with bandgaps too small to achieve maximum efficiency or use cost-prohibitive substrates. Here we demonstrate a material system for intermediate band solar cells using InGaN/GaN quantum-dot-in-nanowire heterostructures grown directly on silicon to provide a lower cost, large-bandgap intermediate band solar cell platform. We demonstrate sequential two-photon current generation with sub-bandgap photons, the hallmark of intermediate band solar cell operation, through vertically stacked quantum dots in the nanowires. Near-infrared light biasing with an 850 nm laser intensity up to 200 W/cm2 increases the photocurrent above and below the bandgap by up to 19% at 78 K, and 44% at room temperature. The nanostructured III-nitride strategy provides a route towards realistic room temperature intermediate band solar cells while leveraging the cost benefits of silicon substrates.

physics.app-ph↗

arXiv2020

Photonic Temperature and Wavelength Metrology by Spectral Pattern Recognition

Spectral pattern recognition is used to measure temperature and generate calibrated wavelength/frequency combs using a single silicon waveguide ring resonator. The ring generates two incommensurate interleaving TE and TM spectral combs that shift independently with temperature to create a spectral pattern that is unique at every temperature. Following an initial calibration, the ring temperature can be determined by recognizing the spectral resonance pattern, and as a consequence the wavelength of every resonance is also known. Two methods of pattern based temperature retrieval are presented. In the first method, the ring is locked to a previously determined temperature set-point defined by the coincidence of only two specific TE and TM cavity modes. Based on a prior calibration at the set-point, the ring temperature and hence all resonance wavelengths are then known and the resulting comb can be used as a wavelength calibration reference. In this configuration, all reference comb wavelengths have been reproduced within a 5 pm accuracy across an 80 nm range by using an on-chip micro-heater to tune the ring. For more general photonic thermometry, a spectral correlation algorithm is developed to recognize a resonance pattern across a 30 nm wide spectral window and thereby determine ring temperature continuously to 50 mK accuracy. The correlation method is extended to simultaneously determine temperature and to identify and correct for wavelength calibration errors in the interrogating light source. The temperature and comb wavelength accuracy is limited primarily by the linewidth of the ring resonances, with accuracy and resolution scaling with the ring quality factor.

physics.optics↗

arXiv2010

Valence holes as Luttinger spinor based qubits in quantum dots

We present a theory of valence holes as Luttinger spinor based qubits in p-doped self-assembled quantum dots within the 4-band $k\cdot p$ formalism. The two qubit levels are identified with the two chiralities of the doubly degenerate ground state. We show that single qubit operations can be implemented with static magnetic field applied along the $z$ and $x$ directions, acting analogously to the $\hatσ_z$ and $\hatσ_x$ operators in the qubit subspace respectively. The coupling of two dots and hence the double qubit operations are shown to be sensitive to the orientation of the two quantum dots. For vertical qubit arrays, there exists an optimal qubit separation suitable for the voltage control of qubit-qubit interactions.

cond-mat.str-el↗