arXiv subjects

S. G. Tantawi

Publications and source records attributed to S. G. Tantawi.

6 recordsLinked to original sources

arXiv2003

Transverse Impedance Bench Measurements in NLC/JLC Accelerating Structures

The wire method is a more rapid and less costly method to measure impedances of RF components compared to methods using a beam. A setup using a single displaced wire to excite and measure transverse resonant modes in accelerating structures for the Next Linear Collider/ Japanese Linear Collider (NLC/JLC) has been built. The RF signal is coupled into and out of the structure using two matching sections with a broadband frequency from 11 to 18 GHz. Their contribution to the scattering parameter is minimized by a calibration technique. A standing wave structure has been measured. Difficulties in accurately predicting the modal loss factors were encountered related to the approximations made and to experimental issues. The measurements are presented and comparisons with simulations are made.

physics.acc-ph↗

arXiv2002

Impedance Measurement Setup for Higher-Order Mode Studies in NLC Accelerator Structures with the Wire Method

Dipole modes are the main cause of transverse emittance dilution in the Japanese Linear Collider / Next Linear Collider (JLC/NLC). A diagnostic setup has been built in order to investigate them. The method is based on using a coaxial wire to excite and measure electromagnetic modes of accelerating structures. This method can offer a more efficient and less expensive procedure than the ASSET facility. Initial measurements have been made and are presented in this paper.

physics.acc-ph↗

arXiv2002

A Resonant Cavity for Single-Shot Emittance Measurement

We present a non-invasive, resonant cavity based approach to beam emittance measurement of a shot-to-shot non-circular beam pulse of multi-bunches. In a resonant cavity, desired field components can be enhanced up to Q_L_lambda/pi, where Q_L_lambda is the loaded Q of the resonance mode lambda, when the cavity resonant mode matches with the beam operating frequency. In particular, a Quad-cavity, with its quadrupole mode at beam operating frequency, extracts the beam quad-moment exclusively, utilizing the symmetry of the cavity and some simple networks to suppress common modes. Six successive beam quadrupole moment measurements, performed at different betatron phases in a linear transport system, allow us to determine the beam emittance, i.e., the beam size and shape in the beam's phase space. One measurement alone provides the rms-beam size if the beam position is given, for instance, by nearby beam-position-monitors. This paper describes the basic design and analysis of a Quad-cavity beam monitoring system.

physics.acc-ph↗

arXiv2002

A Multi-Moded RF Delay Line Distribution System for the Next Linear Collider

The Delay Line Distribution System (DLDS) is an alternative to conventional pulse compression, which enhances the peak power of rf sources while matching the long pulse of those sources to the shorter filling time of accelerator structures. We present an implementation of this scheme that combines pairs of parallel delay lines of the system into single lines. The power of several sources is combined into a single waveguide delay line using a multi-mode launcher. The output mode of the launcher is determined by the phase coding of the input signals. The combined power is extracted from the delay line using mode-selective extractors, each of which extracts a single mode. Hence, the phase coding of the sources controls the output port of the combined power. The power is then fed to the local accelerator structures. We present a detailed design of such a system, including several implementation methods for the launchers, extractors, and ancillary high power rf components. The system is designed so that it can handle the 600 MW peak power required by the NLC design while maintaining high efficiency.

physics.acc-ph↗

arXiv2002

Coaxial Wire Measurements In NLC Accelerating Structures

The coaxial wire method provides an experimental way of measuring wake fields without the need for a particle beam. A special setup has been designed and is in the process of being fabricated at SLAC to measure the loss factors and synchronous frequencies of dipole modes in both traveling and standing wave structures for the Next Linear Collider (NLC). The method is described and predictions based on electromagnetic field simulations are discussed

physics.acc-ph↗

arXiv2001

Planar Waveguide Hybrids for Very High Power RF

Two basic designs have been developed for waveguide hybrids, or 3-dB couplers, capable of handling hundreds of megawatts at X-band. Coupling is provided by one or two connecting waveguides with h-plane junctions and matching elements. In the former case, the connecting waveguide supports two modes. Small apertures and field-enhancing e-bends are avoided to reduce the risk of rf breakdown. The h-plane symmetry also allows the use of over-moded rectangular waveguide in which the height has been increased to reduce field amplitudes without affecting the scattering matrix. The theory and designs are presented, along with the results of prototype tests of functionality and power-handling capability. Such a device is integral to the rf pulse compression or power distribution system of the Next Linear Collider (NLC) for combining, splitting, and directing power. This work was motivated by the observation of rf breakdown at power levels above 200 MW in conventional and modified magic-T's.

physics.acc-ph↗