arXiv subjects

S. Santosh Kumar

Publications and source records attributed to S. Santosh Kumar.

4 recordsLinked to original sources

arXiv2023

Design and Simulation of Capacitive Pressure Sensor for Blood Pressure Sensing Application

This paper presents the mathematical modeling-based design and simulation of normal mode MEMS capacitive pressure sensor for blood pressure sensing application. The normal blood pressure of human being is 120/80 mmHg. But this range varies in case of any stress, hypertension and some other health issues. Analytical simulation is implemented using MATLAB. Basically, normal mode capacitive pressure sensors have a fixed plate and a moveable diaphragm which deflects on application of pressure with the condition that it must not touch the fixed plate. Deflection depends on material as well as thickness, shape and size of diaphragm which can be of circular, elliptical, square or rectangular shape. In this paper, circular shape is chosen due to higher sensitivity compared to other diaphragm shapes. Deflection, base capacitance, change in capacitance after applying pressure and sensitivity are reported for systolic and diastolic blood pressure monitoring application, and study involves determining the optimized design for the sensor. Diaphragm deflection shows linear variation with applied pressure, which follows Hooks law. The variation in capacitance is logarithmic function of applied pressure, which is utilized for analytical simulation.

physics.med-ph↗

arXiv2021

Spatially-Resolved Characterization of Oil-in-Water Emulsion Sprays

This study concerns the effects of pressure, spatial location, and application of oil emulsions on the resulting droplet size, eccentricity, as well as velocity distributions, all of which are crucial information in determining the dispersion dynamics of the droplets during the spray applications. Experiments were conducted with the abovementioned droplets information measured using digital inline holography (DIH). Results show that the volumetric droplet size distributions (VDSD) span widely from sub-200 um to over 2 mm in size. The application of an oil-in-water emulsion results largely in the suppression of smaller droplets, while the VDSD is relatively insensitive to increasing the oil volume fraction beyond a critical level. DIH additionally enables the determination of size-dependent droplet eccentricity and velocity measurements. Interestingly, the application of oil-in-water emulsion generally decreases the eccentricity, more significantly at the center than at the edge of the spray fan. We attribute this decrease to the increase in lamella sheet thickness and thus decrease in characteristic shrinkage rates, consistent with the observation using high-speed shadowgraphs. In all instances, oil-in-water emulsion droplets have higher velocities than equivalent sized water droplets. We attribute this to the earlier action of the spray breakup process in the oil-in-water emulsion, reduced surface energy generation during a breakup (larger droplets), and reduce energy dissipation during breakup with oil-in-water emulsions, leading to increased translational energy after the breakup process. Therefore, it appears that oil-in-water emulsion application simultaneously suppresses small droplet formation and increases droplet velocity, and hence spray penetration in agricultural application.

physics.flu-dyn↗

arXiv2020

Droplet evaporation residue indicating SARS-COV-2 survivability on surfaces

SARS-CoV-2 survives and remains viable on surfaces for several days under different environments as reported in recent studies. However, it is unclear how the viruses survive for such a long time and why their survivability varies across different surfaces. To address these questions, we conduct systematic experiments investigating the evaporation of droplets produced by a nebulizer and human-exhaled gas on surfaces. We found that these droplets do not disappear with evaporation, but instead shrink to a size of a few micrometers (referred to as residues), persist for more than 24 hours, and are highly durable against changes of environmental conditions. The characteristics of these residues change significantly across surface types. Specifically, surfaces with high thermal conductivity like copper do not leave any resolvable residues, while stainless steel, plastic, and glass surfaces form residues from a varying fraction of all deposited droplets at 40% relative humidity. Lowering humidity level suppresses the formation of residues while increasing humidity level enhances it. Our results suggest that these microscale residues can potentially insulate the virus against environmental changes, allowing them to survive inhospitable environments and remain infectious for prolonged durations after deposition. Our findings can also be extended to other viruses transmitted through respiratory droplets (e.g., SARS-CoV, flu viruses, etc.), and can thus lead to practical guidelines for disinfecting surfaces and other prevention measures (e.g., humidity control) for limiting viral transmission.

physics.med-ph↗

arXiv2019

Mathematical Modelling and Comparative Study of Elliptical and Circular Capacitive Pressure Microsensor

A lot of work on clamped circular, square and rectangular shaped capacitive pressure sensor has been carried out. However, to the best of our knowledge, no elaborate work has been performed on mathematical formulation and simulation of clamped elliptical shaped capacitive pressure sensor in literature. This paper describes the mathematical modelling and simulation of normal mode clamped elliptical shaped capacitive pressure sensor. The study of various performance parameters like maximum diaphragm deflection, capacitance variation, mechanical sensitivity, capacitive sensitivity and non-linearity is also carried out for operating pressure range of 0 kPa to 18 kPa. For circular capacitive pressure sensor, the operating pressure range is modified according to physical dimensions i.e. thickness and radius of diaphragm, separation gap between plates and maximum deflection. For same overlapping area between plates (10000*pi mm2), the comparison of elliptical shapes of different eccentricities with circular shape diaphragm is carried out. The thickness of diaphragm is taken as 2 um and separation gap is 1 um in all the designs which are used in this work. In this comparative study, it is observed that elliptical shaped capacitive pressure sensors have better linearity than circular diaphragm pressure sensor.

physics.app-ph↗