arXiv subjects

S. Steinlechner

Publications and source records attributed to S. Steinlechner.

9 recordsLinked to original sources

arXiv2025

Demonstrating the velocity response of a table-top EPR Speedmeter

The sensitivity of gravitational-wave interferometers is fundamentally limited by quantum noise, as dictated by the Heisenberg uncertainty principle, due to their continuous position measurement of the end mirrors. Speedmeter configurations, which measure mirror velocity rather than position, have been proposed as a means to suppress quantum back-action noise, but practical implementations remain at an early stage. In this work, we present a table-top realisation of the Einstein- Podolsky-Rosen (EPR) Speedmeter concept, employing an optical readout scheme based on two orthogonal polarisation modes that probe the interferometer with different effective bandwidths. Using a triangular cavity, we demonstrate that the differential optical response between the linear p- and s-polarised modes exhibits a speed-like frequency dependence: vanishing at DC and increasing linearly with signal frequency, up to the bandwidth of the slower mode. With this we show that an optical system equivalent to the EPR Speedmeter indeed performs a velocity readout of the end mirror.

astro-ph.IM↗

arXiv2025

All-polarisation beamsplitters for interferometer applications

Optical beamsplitters with similar properties for orthogonal, linear polarisation modes are required for realising polarisation-based speedmeter schemes to reduce back-action noise in gravitational-wave interferometers. In this paper, we investigate two beamsplitter coatings obtained from Laseroptik GmbH and Optoman on a best-effort basis that aim for a 50/50 power splitting ratio and equal overall phase shift for two orthogonal, linear polarisation modes interacting with the optic. We show that while Laseroptik GmbH opted for coating stack with 22 alternating layers of Ta2O5 and SiO2, Optoman produced a much thinner coating made of 5 SiO2 and SiOx (0 < x < 2) layers. With these strategies, the Laseroptik coating achieves an equal power reflectivity of 51% at 46 deg angle of incidence, and zero phase shift between both polarisations at 44.25 deg angle of incidence. The Optoman coating achieves power reflectivities of 49% for s-polarisation and 51% for p-polarisation with a differential phase shift around 5 deg largely independent of the angle of incidence.

physics.optics↗

arXiv2022

E-TEST prototype design report

E-TEST (Einstein Telescope Euregio-Meuse-Rhin Site and Technology) is a project recently funded by the European program Ineterreg Euregio Meuse-Rhine. This program is dedicated to innovative cross boarder activities between Belgium, The Netherlands and Germany. With a total budget of15MC and a consortium of 11 partners from the three countries, the objective of the project is twofold. Firstly, to develop an eco-friendly and non-invasive imaging of the geological conditions as well as the development of an observatory of the underground in the EMR region. Secondly, to develop technologies necessary for 3rd generation gravitational wave detectors. In particular, it is proposed to develop a prototype of large suspended cryogenic silicon mirror, isolated from seismic vibrations at low frequency. The total budget of the project is equally spread over the two activities. The first activity is not discussed at all in this report. The E-TEST prototype will have some key unique features: a silicon mirror of 100 kg, a radiative cooling strategy (non contact), a low-frequency hybrid isolation stage, cryogenic sensors and electronics, a laser and optics at 2 microns, a low thermal noise coating.

astro-ph.IM↗

arXiv2022

ETpathfinder: a cryogenic testbed for interferometric gravitational-wave detectors

The third-generation of gravitational wave observatories, such as the Einstein Telescope (ET) and Cosmic Explorer (CE), aim for an improvement in sensitivity of at least a factor of ten over a wide frequency range compared to the current advanced detectors. In order to inform the design of the third-generation detectors and to develop and qualify their subsystems, dedicated test facilities are required. ETpathfinder prototype uses full interferometer configurations and aims to provide a high sensitivity facility in a similar environment as ET. Along with the interferometry at 1550 nm and silicon test masses, ETpathfinder will focus on cryogenic technologies, lasers and optics at 2090 nm and advanced quantum-noise reduction schemes. This paper analyses the underpinning noise contributions and combines them into full noise budgets of the two initially targeted configurations: 1) operating with 1550 nm laser light and at a temperature of 18 K and 2) operating at 2090 nm wavelength and a temperature of 123 K.

astro-ph.IM↗

arXiv2021

Challenges and Opportunities of Gravitational Wave Searches at MHz to GHz Frequencies

The first direct measurement of gravitational waves by the LIGO and Virgo collaborations has opened up new avenues to explore our Universe. This white paper outlines the challenges and gains expected in gravitational wave searches at frequencies above the LIGO/Virgo band, with a particular focus on Ultra High-Frequency Gravitational Waves (UHF-GWs), covering the MHz to GHz range. The absence of known astrophysical sources in this frequency range provides a unique opportunity to discover physics beyond the Standard Model operating both in the early and late Universe, and we highlight some of the most promising gravitational sources. We review several detector concepts which have been proposed to take up this challenge, and compare their expected sensitivity with the signal strength predicted in various models. This report is the summary of the workshop "Challenges and opportunities of high-frequency gravitational wave detection" held at ICTP Trieste, Italy in October 2019, that set up the stage for the recently launched Ultra-High-Frequency Gravitational Wave (UHF-GW) initiative.

gr-qc↗

arXiv2016

Control of a velocity-sensitive audio-band quantum non-demolition interferometer

The Sagnac speed meter interferometer topology can potentially provide enhanced sensitivity to gravitational waves in the audio-band compared to equivalent Michelson interferometers. A challenge with the Sagnac speed meter interferometer arises from the intrinsic lack of sensitivity at low frequencies where the velocity-proportional signal is smaller than the noise associated with the sensing of the signal. Using as an example the on-going proof-of-concept Sagnac speed meter experiment in Glasgow, we quantify the problem and present a solution involving the extraction of a small displacement-proportional signal. This displacement signal can be combined with the existing velocity signal to enhance low frequency sensitivity, and we derive optimal filters to accomplish this for different signal strengths. We show that the extraction of the displacement signal for low frequency control purposes can be performed without reducing significantly the quantum non-demolition character of this type of interferometer.

gr-qc↗

arXiv2015

Quantum noise of non-ideal Sagnac speed meter interferometer with asymmetries

The speed meter concept has been identified as a technique that can potentially provide laser-interferometric measurements at a sensitivity level which surpasses the Standard Quantum Limit (SQL) over a broad frequency range. As with other sub-SQL measurement techniques, losses play a central role in speed meter interferometers and they ultimately determine the quantum noise limited sensitivity that can be achieved. So far in the literature, the quantum noise limited sensitivity has only been derived for lossless or lossy cases using certain approximations (for instance that the arm cavity round trip loss is small compared to the arm cavity mirror transmission). In this article we present a generalised, analytical treatment of losses in speed meters that allows accurate calculation of the quantum noise limited sensitivity of Sagnac speed meters with arm cavities. In addition, our analysis allows us to take into account potential imperfections in the interferometer such as an asymmetric beam splitter or differences of the reflectivities of the two arm cavity input mirrors. Finally,we use the examples of the proof-of-concept Sagnac speed meter currently under construction in Glasgow and a potential implementation of a Sagnac speed meter in the Einstein Telescope (ET) to illustrate how our findings affect Sagnac speed meters with meter- and kilometre-long baselines.

quant-ph↗

arXiv2014

Design of a speed meter interferometer proof-of-principle experiment

The second generation of large scale interferometric gravitational wave detectors will be limited by quantum noise over a wide frequency range in their detection band. Further sensitivity improvements for future upgrades or new detectors beyond the second generation motivate the development of measurement schemes to mitigate the impact of quantum noise in these instruments. Two strands of development are being pursued to reach this goal, focusing both on modifications of the well-established Michelson detector configuration and development of different detector topologies. In this paper, we present the design of the world's first Sagnac speed meter interferometer which is currently being constructed at the University of Glasgow. With this proof-of-principle experiment we aim to demonstrate the theoretically predicted lower quantum noise in a Sagnac interferometer compared to an equivalent Michelson interferometer, to qualify Sagnac speed meters for further research towards an implementation in a future generation large scale gravitational wave detector, such as the planned Einstein Telescope observatory.

gr-qc↗

arXiv2009

Building blocks for future detectors: Silicon test masses and 1550 nm laser light

Current interferometric gravitational wave detectors use the combination of quasi-monochromatic, continuous-wave laser light at 1064 nm and fused silica test masses at room temperature. Detectors of the third generation, such as the Einstein-Telescope, will involve a considerable sensitivity increase. The combination of 1550 nm laser radiation and crystalline silicon test masses at low temperatures might be important ingredients in order to achieve the sensitivity goal. Here we compare some properties of the fused silica and silicon test mass materials relevant for decreasing the thermal noise in future detectors as well as the recent technology achievements in the preparation of laser radiation at 1064 nm and 1550 nm relevant for decreasing the quantum noise. We conclude that silicon test masses and 1550 nm laser light have the potential to form the future building blocks of gravitational wave detection.

physics.ins-det↗