Searcharxiv⌕ Search

arXiv subjects

S. V. Shotin

Publications and source records attributed to S. V. Shotin.

5 recordsLinked to original sources

Effect of superplastic deformation on the intergranular corrosion resistance of austenitic steel 321 with different types of UFG structure: A case of homogeneous and heterogeneous microstructure obtained by ECAP

The effects of superplasticity (SP) on the structure, hardness, and intergranular corrosion (IGC) resistance of UFG 321L steel are reported. By increasing the number of the ECAP cycles (N) and varying the ECAP temperature, and annealing temperature, the degree of the microstructural heterogeneity was changed. Regardless of the microstructural homogeneity degree, UFG steels demonstrated the possibility of realizing the SP effect at temperatures below the onset temperature of dynamic recrystallization. The dependence of ductility of the UFG steel on the test temperature is non-monotonic with a minimum at 450-600C. The maximum elongation to failure (~250%) was achieved at a SP temperature of 800C. The SP deformation of the UFG steel is controlled by the power law creep. It is shown that the hardness of UFG steel samples after SP is equal than the hardness of UFG steels annealed at the same temperature. It is also shown what SP leads to a decrease in the IGC resistance of the UFG steel. Heterostructured steel have reduced ductility, as well as lower resistance to IGC after tension tests at room temperature (RT). The minimum IGC resistance is ensured at N=2, and the maximum - at N=4. The IGC resistance of homogeneous UFG samples after tension testing exceeds the IGC resistance of coarse-grained steel. Tension test at a RT has the greatest negative effect on the IGC resistance of heterostructured steel, and the least negative effect on the IGC resistance of homogeneous steel. Increasing the number of ECAP cycles enhances the ductility of the UFG steel at 750-900C. Increasing the ECAP temperature results in a simultaneous decrease in ductility and flow stress. Heterostructured steel exhibits minimal values of the activation energy of SP deformation. Increasing the number of ECAP cycles and increasing the ECAP temperature lead to an increase in the activation energy of SP deformation.

cond-mat.mtrl-sci↗

Superplasticity-like behavior of ultrafine-grained austenitic steel 321

Hot rolled commercial metastable austenitic steel 321 with strongly elongated thin delta-ferrite particles in its microstructure was the object of investigations. Ultrafine-grained (UFG) microstructure in steel 321 was formed by Equal Channel Angular Pressing (ECAP) at 150 oC and 450 oC. When heating the UFG steel specimens, the nucleation of sigma-phase particles blocking the grain boundary migration was observed. The maximum elongation to failure (~250%) was achieved at the deformation temperature 750 oC. The process of superplastic deformation of the UFG steel 321 is controlled by simultaneous grain boundary sliding and power-law creep. The contribution of each process depends on the grain growth rate in the superplasticity regime as well as on defect accumulation on the grain boundaries. The fracture of the UFG steel 321 specimens has a cavitational character - an intensive formation of large elongated pores at the non-metallic particles as well as of the submicron pores at the sigma-phase particles in the course of superplastic deformation were observed.

cond-mat.mtrl-sci↗

Microstructure Thermal Stability and Superplastic Behavior of Al-6%Mg-0.12%Sc-0.10%Zr-0.10%(Yb, Er, Hf) Ultrafine-Grained Alloys

Superplastic behavior of ultrafine-grained (UFG) Al-6Mg-0.12Sc-0.10Zr-0.1X alloys, where X = Yb (Alloy #1-Yb), Er (Alloy #2-Er), and Hf (Alloy #3-Hf), has been studied. The total content of Sc, Zr, Yb, Er, Hf in the alloys was 0.32 wt.% (0.117-0.118 at.%). The alloys used for benchmarking were Al-6Mg-0.12Sc-0.20Zr (Alloy #4-Zr) and Al-6Mg-0.22Sc-0.10Zr (Alloy #5-Sc). Their UFG microstructure was formed with ECAP. Two different types of deformation behavior during superplasticity were demonstrated. A simultaneous increase in yield stress and elongation to failure during superplastic deformation was discovered. High deformation temperatures were shown to cause a competition between dynamic (strain-induced) grain growth and dynamic recrystallization, leading to a finer grain microstructure. The values of strain hardening factor (n), strain rate sensitivity factor (m), and superplastic deformation threshold stress (Sp) were determined. The impact of the type and concentration of alloying elements on the deformation behavior and dynamic grain growth of Al-6%Mg alloys was investigated. It was established that the maximum elongation to failure in Alloy #1-Yb and Alloy #2-Er is observed at lower deformation temperatures than in Alloy #4-Zr and Alloy #5-Sc. The superplastic properties of Alloy #3-Hf are superior to those of Alloy #4-Zr and Alloy #5-Sc with high content of alloying elements (in at.%). Alloy #1-Yb manifests good elongation to failure (910%) at low temperatures (400 oC). The satisfiability of Hart's criterion for calculating uniform deformation value under superplastic conditions was verified. It was demonstrated that cavitation when pores are formed in large Al3X particles at high temperatures causes early failure of aluminum alloys.

cond-mat.mtrl-sci↗

Effect of grain boundary state and grain size on the microstructure and mechanical properties of alumina obtained by SPS: A case of the amorphous layer on particle surface

The effect of temperature modes and heating rates (Vh) on the shrinkage kinetics of submicron and fine aluminum oxide powders has been studied. The objects of research comprised (i) submicron alfa-Al2O3 powder, (ii) submicron alfa-Al2O3 powder with an amorphous layer on particle surface, (iii) fine alfa-Al2O3 powder. The alumina ceramic specimens were produced by Spark Plasma Sintering (SPS). Equally fine powders (i) and (ii) were used to analyze the effect of an amorphous layer on sintering kinetics. Powders (i) and (iii) were used to analyze the effect of the initial particle size on shrinkage kinetics. Shrinkage curves were analyzed using the Young-Cutler and Coble models. It has been shown that sintering kinetics is determined by the intensity of grain boundary diffusion for submicron powders and by simultaneous lattice and grain boundary diffusion for fine powders. It has been determined that an amorphous layer on the surface of submicron alfa-Al2O3 powder affects grain boundary migration rate and the Coble equation parameters at SPS final stages. It has been suggested that abnormal characteristics of the alumina ceramics sintered from a submicron powder with an amorphous layer on the particle surface are associated with an increased concentration of defects at grain boundaries that were formed during crystallization of the amorphous layer.

cond-mat.mtrl-sci↗

Effect of ECAP and heat treatment on mechanical properties, stress relaxation behavior and corrosion resistance of a 321-type austenitic steel with increased delta-ferrite content

Hot rolled commercial metastable austenitic steel 0.8C-18Cr-10Ni-0.1Ti (Russian industrial name 08X18H10T, analog 321L) with strongly elongated thin delta-ferrite particles in its microstructure was the object of investigations. The lengths of these delta-particles were up to 500 mkm, the thickness was 10 mkm. The formation of the strain-induced martensite as well as the grinding of the austenite and of the delta-ferrite grains take place during ECAP. During the annealing of the UFG steel, the formation of the delta-phase particles takes place. These particles affect the grain boundary migration and the strength of the steel. However, a reduction of the Hall-Petch coefficient as compared to the coarse-grained (CG) steel due to the fragmentation of the delta-ferrite particles was observed. The samples of the UFG steel were found to have 2-3 times higher stress relaxation resistance as compared to the CG steel (a higher macroelasticity stress and a lower stress relaxation magnitude). The differences in the stress relaxation resistance of the UFG and CG steels were investigated. ECAP was shown to result in an increase in the corrosion rate and in an increased tendency to the intergranular corrosion (IGC). The reduction of the corrosion resistance of the UFG steel was found to originate from the increase in the fraction of the strain-induced martensite during ECAP.

cond-mat.mtrl-sci↗