arXiv subjects

S. Vitale

Publications and source records attributed to S. Vitale.

At least 37 records · Page 2Linked to original sources

arXiv2014

Free-flight experiments in LISA Pathfinder

The LISA Pathfinder mission will demonstrate the technology of drag-free test masses for use as inertial references in future space-based gravitational wave detectors. To accomplish this, the Pathfinder spacecraft will perform drag-free flight about a test mass while measuring the acceleration of this primary test mass relative to a second reference test mass. Because the reference test mass is contained within the same spacecraft, it is necessary to apply forces on it to maintain its position and attitude relative to the spacecraft. These forces are a potential source of acceleration noise in the LISA Pathfinder system that are not present in the full LISA configuration. While LISA Pathfinder has been designed to meet it's primary mission requirements in the presence of this noise, recent estimates suggest that the on-orbit performance may be limited by this `suspension noise'. The drift-mode or free-flight experiments provide an opportunity to mitigate this noise source and further characterize the underlying disturbances that are of interest to the designers of LISA-like instruments. This article provides a high-level overview of these experiments and the methods under development to analyze the resulting data.

gr-qc↗

arXiv2012

The interaction between stray electrostatic fields and a charged free-falling test mass

We present an experimental analysis of force noise caused by stray electrostatic fields acting on a charged test mass inside a conducting enclosure, a key problem for precise gravitational experiments. Measurement of the average field that couples to test mass charge, and its fluctuations, is performed with two independent torsion pendulum techniques, including direct measurement of the forces caused by a change in electrostatic charge. We analyze the problem with an improved electrostatic model that, coupled with the experimental data, also indicates how to correctly measure and null the stray field that interacts with test mass charge. Our measurements allow a conservative upper limit on acceleration noise, of 2 fm/s$^2$\rthz\ for frequencies above 0.1 mHz, for the interaction between stray fields and charge in the LISA gravitational wave mission.

gr-qc↗

arXiv2012

Towards a generic test of the strong field dynamics of general relativity using compact binary coalescence: Further investigations

In this paper we elaborate on earlier work by the same authors in which a novel Bayesian inference framework for testing the strong-field dynamics of General Relativity using coalescing compact binaries was proposed. Unlike methods that were used previously, our technique addresses the question whether one or more 'testing coefficients' (e.g. in the phase) parameterizing deviations from GR are non-zero, rather than all of them differing from zero at the same time. The framework is well-adapted to a scenario where most sources have low signal-to-noise ratio, and information from multiple sources as seen in multiple detectors can readily be combined. In our previous work, we conjectured that this framework can detect generic deviations from GR that can in principle not be accomodated by our model waveforms, on condition that the change in phase near frequencies where the detectors are the most sensitive is comparable to that induced by simple shifts in the lower-order phase coefficients of more than a few percent ($\sim 5$ radians at 150 Hz). To further support this claim, we perform additional numerical experiments in Gaussian and stationary noise according to the expected Advanced LIGO/Virgo noise curves, and coherently injecting signals into the network whose phasing differs structurally from the predictions of GR, but with the magnitude of the deviation still being small. We find that even then, a violation of GR can be established with good confidence.

gr-qc↗

arXiv2012

Towards a generic test of the strong field dynamics of general relativity using compact binary coalescence

Coalescences of binary neutron stars and/or black holes are amongst the most likely gravitational-wave signals to be observed in ground based interferometric detectors. Apart from the astrophysical importance of their detection, they will also provide us with our very first empirical access to the genuinely strong-field dynamics of General Relativity (GR). We present a new framework based on Bayesian model selection aimed at detecting deviations from GR, subject to the constraints of the Advanced Virgo and LIGO detectors. The method tests the consistency of coefficients appearing in the waveform with the predictions made by GR, without relying on any specific alternative theory of gravity. The framework is suitable for low signal-to-noise ratio events through the construction of multiple subtests, most of which involve only a limited number of coefficients. It also naturally allows for the combination of information from multiple sources to increase one's confidence in GR or a violation thereof. We expect it to be capable of finding a wide range of possible deviations from GR, including ones which in principle cannot be accommodated by the model waveforms, on condition that the induced change in phase at frequencies where the detectors are the most sensitive is comparable to the effect of a few percent change in one or more of the low-order post-Newtonian phase coefficients. In principle the framework can be used with any GR waveform approximant, with arbitrary parameterized deformations, to serve as model waveforms. In order to illustrate the workings of the method, we perform a range of numerical experiments in which simulated gravitational waves modeled in the restricted post-Newtonian, stationary phase approximation are added to Gaussian and stationary noise that follows the expected Advanced LIGO/Virgo noise curves.

gr-qc↗

arXiv2012

Parameter estimation in LISA Pathfinder operational exercises

The LISA Pathfinder data analysis team has been developing in the last years the infrastructure and methods required to run the mission during flight operations. These are gathered in the LTPDA toolbox, an object oriented MATLAB toolbox that allows all the data analysis functionalities for the mission, while storing the history of all operations performed to the data, thus easing traceability and reproducibility of the analysis. The parameter estimation methods in the toolbox have been applied recently to data sets generated with the OSE (Off-line Simulations Environment), a detailed LISA Pathfinder non-linear simulator that will serve as a reference simulator during mission operations. These operational exercises aim at testing the on-orbit experiments in a realistic environment in terms of software and time constraints. These simulations, so called operational exercises, are the last verification step before translating these experiments into tele-command sequences for the spacecraft, producing therefore very relevant datasets to test our data analysis methods. In this contribution we report the results obtained with three different parameter estimation methods during one of these operational exercises.

gr-qc↗

arXiv2011

Brownian force noise from molecular collisions and the sensitivity of advanced gravitational wave observatories

We present an analysis of Brownian force noise from residual gas damping of reference test masses as a fundamental sensitivity limit in small force experiments. The resulting acceleration noise increases significantly when the distance of the test mass to the surrounding experimental apparatus is smaller than the dimension of the test mass itself. For the Advanced LIGO interferometric gravitational wave observatory, where the relevant test mass is a suspended 340 mm diameter cylindrical end mirror, the force noise power is increased by roughly a factor 40 by the presence of a similarly shaped reaction mass at a nominal separation of 5 mm. The force noise, of order 20 fN\rthz\ for $2 \times 10^{-6}$ Pa of residual H$_2$ gas, rivals quantum optical fluctuations as the dominant noise source between 10 and 30 Hz. We present here a numerical and analytical analysis for the gas damping force noise for Advanced LIGO, backed up by experimental evidence from several recent measurements. Finally, we discuss the impact of residual gas damping on the gravitational wave sensitivity and possible mitigation strategies.

gr-qc↗

arXiv2011

Non-linear parameter estimation for the LTP experiment: analysis of an operational exercise

The precursor ESA mission LISA-Pathfinder, to be flown in 2013, aims at demonstrating the feasibility of the free-fall, necessary for LISA, the upcoming space-born gravitational wave observatory. LISA Technology Package (LTP) is planned to carry out a number of experiments, whose main targets are to identify and measure the disturbances on each test-mass, in order to reach an unprecedented low-level residual force noise. To fulfill this plan, it is then necessary to correctly design, set-up and optimize the experiments to be performed on-flight and do a full system parameter estimation. Here we describe the progress on the non-linear analysis using the methods developed in the framework of the \textit{LTPDA Toolbox}, an object-oriented MATLAB Data Analysis environment: the effort is to identify the critical parameters and remove the degeneracy by properly combining the results of different experiments coming from a closed-loop system like LTP.

astro-ph.IM↗

arXiv2011

Time domain maximum likelihood parameter estimation in LISA Pathfinder Data Analysis

LISA is the upcoming space-based Gravitational Wave telescope. LISA Pathfinder, to be launched in the coming years, will prove and verify the detection principle of the fundamental Doppler link of LISA on a flight hardware identical in design to that of LISA. LISA Pathfinder will collect a picture of all noise disturbances possibly affecting LISA, achieving the unprecedented pureness of geodesic motion necessary for the detection of gravitational waves. The first steps of both missions will crucially depend on a very precise calibration of the key system parameters. Moreover, robust parameters estimation is of fundamental importance in the correct assessment of the residual force noise, an essential part of the data processing for LISA. In this paper we present a maximum likelihood parameter estimation technique in time domain being devised for this calibration and show its proficiency on simulated data and validation through Monte Carlo realizations of independent noise runs. We discuss its robustness to non-standard scenarios possibly arising during the real-life mission, as well as its independence to the initial guess and non-gaussianities. Furthermore, we apply the same technique to data produced in mission-like fashion during operational exercises with a realistic simulator provided by ESA.

physics.data-an↗

arXiv2011

Increased Brownian force noise from molecular impacts in a constrained volume

We report on residual gas damping of the motion of a macroscopic test mass enclosed in a nearby housing in the molecular flow regime. The damping coefficient, and thus the associated thermal force noise, is found to increase significantly when the distance between test mass and surrounding walls is smaller than the test mass itself. The effect has been investigated with two torsion pendulums of different geometry and has been modelled in a numerical simulation whose predictions are in good agreement with the measurements. Relevant to a wide variety of small-force experiments, the residual-gas force noise power for the test masses in the LISA gravitational wave observatory is roughly a factor 15 larger than in an infinite gas volume, though still compatible with the target acceleration noise of 3 fm s^-2 Hz^-1/2 at the foreseen pressure below 10^-6 Pa.

gr-qc↗

arXiv2010

Bayesian parameter estimation in the second LISA Pathfinder Mock Data Challenge

A main scientific output of the LISA Pathfinder mission is to provide a noise model that can be extended to the future gravitational wave observatory, LISA. The success of the mission depends thus upon a deep understanding of the instrument, especially the ability to correctly determine the parameters of the underlying noise model. In this work we estimate the parameters of a simplified model of the LISA Technology Package (LTP) instrument. We describe the LTP by means of a closed-loop model that is used to generate the data, both injected signals and noise. Then, parameters are estimated using a Bayesian framework and it is shown that this method reaches the optimal attainable error, the Cramer-Rao bound. We also address an important issue for the mission: how to efficiently combine the results of different experiments to obtain a unique set of parameters describing the instrument.

gr-qc↗

arXiv2010

IGEC2: A 17-month search for gravitational wave bursts in 2005-2007

We present here the results of a 515 days long run of the IGEC2 observatory, consisting of the four resonant mass detectors ALLEGRO, AURIGA, EXPLORER and NAUTILUS. The reported results are related to the fourfold observation time from Nov. 6 2005 until Apr. 14 2007, when Allegro ceased its operation. This period overlapped with the first long term observations performed by the LIGO interferometric detectors. The IGEC observations aim at the identification of gravitational wave candidates with high confidence, keeping the false alarm rate at the level of 1 per century, and high duty cycle, namely 57% with all four sites and 94% with at least three sites in simultaneous observation. The network data analysis is based on time coincidence searches over at least three detectors: the four 3-fold searches and the 4-fold one are combined in a logical OR. We exchanged data with the usual blind procedure, by applying a unique confidential time offset to the events in each set of data. The accidental background was investigated by performing sets of 10^8 coincidence analyses per each detector configuration on off-source data, obtained by shifting the time series of each detector. The thresholds of the five searches were tuned so as to control the overall false alarm rate to 1/century. When the confidential time shifts was disclosed, no gravitational wave candidate was found in the on-source data. As an additional output of this search, we make available to other observatories the list of triple coincidence found below search thresholds, corresponding to a false alarm rate of 1/month.

gr-qc↗

arXiv2010

Gas damping force noise on a macroscopic test body in an infinite gas reservoir

We present a simple analysis of the force noise associated with the mechanical damping of the motion of a test body surrounded by a large volume of rarefied gas. The calculation is performed considering the momentum imparted by inelastic collisions against the sides of a cubic test mass, and for other geometries for which the force noise could be an experimental limitation. In addition to arriving at an accurated estimate, by two alternative methods, we discuss the limits of the applicability of this analysis to realistic experimental configurations in which a test body is surrounded by residual gas inside an enclosure that is only slightly larger than the test body itself.

physics.class-ph↗

arXiv2009

Nonequilibrium steady state fluctuations in actively cooled resonators

We analyze heat and work fluctuations in the gravitational wave detector AURIGA, modeled as a macroscopic electromechanical oscillator in contact with a thermostat and cooled by an active feedback system. The oscillator is driven to a steady state by the feedback cooling, equivalent to a viscous force. The experimentally measured fluctuations are in agreement with our theoretical analysis based on a stochastically driven Langevin system. The asymmetry of the fluctuations of the absorbed heat characterizes the oscillator's nonequilibrium steady state and reveals the extent to which a feedback cooled system departs from equilibrium in a statistical mechanics perspective.

cond-mat.stat-mech↗

arXiv2008

Feedback cooling of the normal modes of a massive electromechanical system to submillikelvin temperature

We apply a feedback cooling technique to simultaneously cool the three electromechanical normal modes of the ton-scale resonant-bar gravitational wave detector AURIGA. The measuring system is based on a dc Superconducting Quantum Interference Device (SQUID) amplifier, and the feedback cooling is applied electronically to the input circuit of the SQUID. Starting from a bath temperature of 4.2 K, we achieve a minimum temperature of 0.17 mK for the coolest normal mode. The same technique, implemented in a dedicated experiment at subkelvin bath temperature and with a quantum limited SQUID, could allow to approach the quantum ground state of a kilogram-scale mechanical resonator.

quant-ph↗

arXiv2007

Thermal gradient-induced forces on geodetic reference masses for LISA

The low frequency sensitivity of space-borne gravitational wave observatories will depend critically on the geodetic purity of the trajectories of orbiting test masses. Fluctuations in the temperature difference across the enclosure surrounding the free-falling test mass can produce noisy forces through several processes, including the radiometric effect, radiation pressure, and outgassing. We present here a detailed experimental investigation of thermal gradient-induced forces for the LISA gravitational wave mission and the LISA Pathfinder, employing high resolution torsion pendulum measurements of the torque on a LISA-like test mass suspended inside a prototype of the LISA gravitational reference sensor that will surround the test mass in orbit. The measurement campaign, accompanied by numerical simulations of the radiometric and radiation pressure effects, allows a more accurate and representative characterization of thermal-gradient forces in the specific geometry and environment relevant to LISA free-fall. The pressure dependence of the measured torques allows clear identification of the radiometric effect, in quantitative agreement with the model developed. In the limit of zero gas pressure, the measurements are most likely dominated by outgassing, but at a low level that does not threaten the LISA sensitivity goals.

gr-qc↗

arXiv2006

Torsion pendulum facility for direct force measurements of LISA GRS related disturbances

A four mass torsion pendulum facility for testing of the LISA GRS is under development in Trento. With a LISA-like test mass suspended off-axis with respect to the pendulum fiber, the facility allows for a direct measurement of surface force disturbances arising in the GRS. We present here results with a prototype pendulum integrated with very large-gap sensors, which allows an estimate of the intrinsic pendulum noise floor in the absence of sensor related force noise. The apparatus has shown a torque noise near to its mechanical thermal noise limit, and would allow to place upper limits on GRS related disturbances with a best sensitivity of 300 fN/Hz^(1/2) at 1mHz, a factor 50 from the LISA goal. Also, we discuss the characterization of the gravity gradient noise, one environmental noise source that could limit the apparatus performances, and report on the status of development of the facility.

gr-qc↗

arXiv2005

Upper limits on gravitational waves emission in association with the Dec 27 2004 giant flare of SGR1806-20

At the time when the giant flare of SGR1806-20 occurred, the AURIGA "bar" gw detector was on the air with a noise performance close to stationary gaussian. This allows to set relevant upper limits, at a number of frequencies in the vicinities of 900 Hz, on the amplitude of the damped gw wave trains, which, according to current models, could have been emitted, due to the excitation of normal modes of the star associated with the peak in X-rays luminosity.

astro-ph↗

arXiv2005

Measuring the LISA test mass magnetic proprieties with a torsion pendulum

Achieving the low frequency LISA sensitivity requires that the test masses acting as the interferometer end mirrors are free-falling with an unprecedented small degree of deviation. Magnetic disturbances, originating in the interaction of the test mass with the environmental magnetic field, can significantly deteriorate the LISA performance and can be parameterized through the test mass remnant dipole moment $\vec{m}_r$ and the magnetic susceptibility $χ$. While the LISA test flight precursor LTP will investigate these effects during the preliminary phases of the mission, the very stringent requirements on the test mass magnetic cleanliness make ground-based characterization of its magnetic proprieties paramount. We propose a torsion pendulum technique to accurately measure on ground the magnetic proprieties of the LISA/LTP test masses.

gr-qc↗