arXiv subjects

Sabine Riemann

Publications and source records attributed to Sabine Riemann.

At least 19 recordsLinked to original sources

arXiv2023

R&D for Positron Sources at High-Energy Lepton Colliders

Several designs for high-energy Lepton Colliders serving as Higgs factories but extendable to higher energies up to the TeV range are under discussion. The most mature design is the International Linear Collider (ILC), but also the Compact Linear Collider (CLIC) as well as the new concept of a Hybrid Asymmetric Linear Higgs Factory (HALHF) have a large physics potential. The first energy stage with $\sqrt{s}=250$~GeV requires high luminosity and polarized beams and imposes an effort for all positron source designs at high-energy colliders. In the baseline design of the ILC, an undulator-based source is foreseen for the positron source in order to match the physics requirements. In this contribution an overview is given about the undulator-based source, the target tests, the rotating target wheel design, as well as the pulsed solenoid and the new technology development of plasma lenses as optic matching devices.

hep-ph↗

arXiv2023

Target tests for the ILC positron source Talk presented at the International Workshop on Future Linear Colliders (LCWS2023)

The positron source is an essential component of the International Linear Collider (ILC) and is an area that poses some design challenges. One consideration is the material for the target, where the 1014 positrons per second for the ILC are generated. The potential material would need to be able to resist the high load created by the intense high energy photon beam. One of such candidates is the titanium alloy Ti-6Al-4V, for which the results of material tests with 3.5 MeV electrons are shown. The material was characterized after the irradiation by high-energy X-ray diffraction (HE-XRD) and changes caused by the irradiation to the crystal structure were studied. These tests revealed there was only minimal change in the phase fractions and crystal structure of the material under conditions as expected for the ILC.

physics.acc-ph↗

arXiv2021

Photon Masks for the ILC Positron Source with 175 and 250 GeV Electron Drive Beam

In the future the International Linear Collider (ILC), a helical undulator-based polarized positron source, is expected to be chosen. A high energy electron beam passes through a superconducting helical undulator in order to create circularly polarized photons which will be directed to a conversion target, resulting in electron-positron pairs. The resulting positron beam is longitudinally polarized. Since the photons are produced with an opening angle and pass through a long superconducting helical undulator, some of these photons will strike the undulator walls. Therefore photon masks must be placed along the undulator line in order to keep the power deposited in the undulator walls below the acceptable limit of 1W/m. The baseline design of the ILC is focused on 250 GeV center-of-mass energy and upgrade to center-of-mass energies of 350 and 500 GeV is foreseen. This paper shows a detailed study of the ideal power deposited along the masks for both 350 and 500 GeV center-of-mass energies.

physics.acc-ph↗

arXiv2020

Plasma Lenses: Possible alternative OMD at the ILC

In the baseline design of the International Linear Collider (ILC) an undulator-based source is foreseen for the positron source in order to match the physics requirements. The recently chosen first energy stage with sqrt(s)=250 GeV requires high luminosity and imposes an effort for all positron source designs at high-energy colliders. In this paper we perform a simulation study and adopt the new technology of plasma lenses to capture the positrons generated by the undulator photons and to create the required high luminosity positron beam.

physics.acc-ph↗

arXiv2020

Updated status of the undulator-based ILC positron source

The design of the positron source for the International Linear Collider (ILC) is still under discussion. The baseline design plans to use the high-energy electron beam for the positron production before it goes to the IP. The electrons pass a long helical undulator and generate an intense circularly polarized photon beam which hits a thin conversion target to produce $e^+e^-$ pairs. The resulting positron beam is longitudinally polarized which provides an important benefit for precision physics analyses at the ILC. In this paper the status of the positron target design studies is presented. Focus is the positron yield for center-of-mass energies of 250 GeV and also the Z peak. Possibilities to improve the positron collection system and thus to increase the positron yield are discussed.

physics.acc-ph↗

arXiv2020

Energy Deposition due to Secondary Particles in The Helical Undulator Wall at ILC-250GeV

In the future, International Linear Collider (ILC), a helical undulator based polarized positron source is expected to be chosen. A high energy electron beam passes through a superconducting helical undulator in order to create circularly polarized photons which will be directed to a conversion target, the result of which, will be electron-positron pairs. The resulting positron beam is longitudinally polarized. In order to produce the required number of positrons in ILC250 the full undulator length is needed. Since the photons are created with an opening angle and traveling through a 320 m long undulator, it is expected that the superconducting undulator vacuum will be hit by the photons. Photon masks are needed to be inserted in the undulator line to keep the power deposition in the vacuum below the acceptable limit which is 1W/m. A detailed study of the power deposition in the vacuum and masks is needed in order to design the photon masks. This paper describes the power deposition in the undulator vacuum due to secondary particles assuming an ideal undulator. In addition, the mask model is proposed.

physics.acc-ph↗

arXiv2019

Status of the undulator-based ILC positron source

The design of the positron source for the International Linear Collider (ILC) is still under consideration. The baseline design plans to use the electron beam for the positron production before it goes to the IP. The high-energy electrons pass a long helical undulator and generate an intense circularly polarized photon beam which hits a thin conversion target to produce $e^+e^-$ pairs. The resulting positron beam is longitudinally polarized which provides an important benefit for precision physics analyses. In this paper the status of the design studies is presented with focus on ILC250. In particular, the target design and cooling as well as issues of the optical matching device are important for the positron yield. Some possibilities to optimize the system are discussed.

physics.acc-ph↗

arXiv2019

Energy Deposition along The Helical Undulator at ILC-250GeV

The positron source of the International Linear Collider is based on a superconducting helical undulator passed by the high-energy electron beam to generate photons which hit a conversion target. Since the photons are circularly polarized the resulting positron beam is polarized. At ILC250, the full undulator is needed to produce the required number of positrons. To keep the power deposition in the undulator walls below the acceptable limit of 1W/m, photon masks must be inserted in the undulator line. The photon mask design requires a detailed study of the power deposition in the walls and masks. This paper describes the power deposition in the undulator wall due to synchrotron radiation.

physics.acc-ph↗

arXiv2019

Optimization of Undulator Parameters for 125 GeV Drive Beam

In the baseline design of the International Linear Collider (ILC) an undulator-based source is foreseen for the positron source in order to match the physics requirements. The baseline parameters are optimized for the ILC at sqrt(s)=500 GeV, that means an electron drive beam of 250 GeV. Precision measurements in the Higgs sector, however, require measurements at sqrt(s)=250 GeV, i.e. running with the electron drive beam only at 125 GeV, which imposes a challenge for achieving a high yield. Therefore the baseline undulator parameters have to be optimized as much as possible within their technical performances. In this bachelor thesis we therefore present a theoretical study on the radiation spectra of a helical undulator, based on the equation for the radiated synchrotron energy spectral density per solid angle per electron in the relativistic, far-field and point-like charge approximation. From this starting point the following undulator properties are examined: the deposited power in the undulator vessel, which can disrupt the functionality of the undulator magnets, the protective property of a mask on this disturbances and the number of positrons produced by the synchrotron radiation in a Ti6Al4V target. Those quantities were evaluated for various values for parameters as undulator period, undulator length and magnetic flux in order to find optimal baseline parameter sets for sqrt(s)=250 GeV.

physics.acc-ph↗

arXiv2018

The Energy Deposition on the ILC Realistic Undulator Wall

Since the undulator wall is being bombarded by photon produced in the ILC helical undulator, masks were installed inside the undulator to protect the superconducting undulator as well as the vacuum. The photon energy spectrum was used to calculate the incident power. HUSR software was used to simulate the photon energy spectrum per meter inside the undulator. The influence of adding masks inside the undulator on the photon polarisation and energy spectrum was also studied.

physics.acc-ph↗

arXiv2018

The ILC positron target cooled by thermal radiation

The design of the conversion target for the undulator-based ILC positron source is still under development. One important issue is the cooling of the target. Here, the status of the design studies for cooling by thermal radiation is presented.

physics.acc-ph↗

arXiv2018

Undulator-Based Positron Source at 250 GeV CM Energy with Different Optical Matching Devices: Pulsed Flux Concentrator and Quarter Wave Transformer

In the baseline design of the International Linear Collider (ILC) an undulator-based source is foreseen for the positron source. In this study the energy deposition in the pulsed flux concentrator (FC) of positron source is calculated for the ILC at 250 GeV center-of-mass energy. The peak energy of 33 J/g deposited by one beam pulse in the current design of the FC is above the limit for copper material. Several promising options were considered to solve the issue of overheating the FC: the quarter wave transformer (QWT) has a significantly bigger aperture and is considered as an valuable and safe alternative for the FC. Since the positron source with a QWT is expected to lead to a lower positron capture efficiency, also the expected positron yield was calculated in addition to the energy deposition in QWT.

physics.acc-ph↗

arXiv2018

The role of positron polarization for the inital $250$ GeV stage of the International Linear Collider

The International Linear Collider is now proposed with a staged machine design, with the first stage at $\sqrt{s}=$~250 GeV and an integrated luminosity goal of 2~ab$^{-1}$. One of the questions for the machine design is the importance of positron polarization. In this report, we review the impact of positron polarization on the physics goals of the $250$ GeV stage of the ILC and demonstrate that positron polarization has distinct advantages.

hep-ph↗

arXiv2014

ZFITTER 1985-2013

The ZFITTER project is aimed at the computation of high-precision theoretical predictions for various observables in high-energy electron-positron annihilation and other processes. The stages of the project development are described. Accent is made on applications to the analysis of LEP data. The present status of the project and perspectives are given as well.

hep-ph↗

arXiv2013

Physics at the CLIC e+e- Linear Collider -- Input to the Snowmass process 2013

This paper summarizes the physics potential of the CLIC high-energy e+e- linear collider. It provides input to the Snowmass 2013 process for the energy-frontier working groups on The Higgs Boson (HE1), Precision Study of Electroweak Interactions (HE2), Fully Understanding the Top Quark (HE3), as well as The Path Beyond the Standard Model -- New Particles, Forces, and Dimensions (HE4). It is accompanied by a paper describing the CLIC accelerator study, submitted to the Frontier Capabilities group of the Snowmass process.

hep-ex↗

arXiv2013

The International Linear Collider Technical Design Report - Volume 2: Physics

The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selected and the necessary site-dependent engineering is carried out, construction can begin immediately. The TDR also gives baseline documentation for two high-performance detectors that can share the ILC luminosity by being moved into and out of the beam line in a "push-pull" configuration. These detectors, ILD and SiD, are described in detail. They form the basis for a world-class experimental programme that promises to increase significantly our understanding of the fundamental processes that govern the evolution of the Universe.

hep-ph↗

arXiv2013

Positron Source Simulations for ILC 1 TeV Upgrade

The generation and capture of polarized positrons at a source with a superconducting helical undulator having 4.3 cm period and 500 GeV electron drive beam have been simulated. The positron polarization has been calculated for the different undulator K values (up to K = 2.5). Without applying a photon collimator, the maximal polarization of positrons is about 25% for 231 meters active magnet length of undulator with K = 0.7. Using an undulator with K = 2.5 and a collimator with an aperture radius of 0.9 mm results in increase of positron polarization to 54%. The energy deposition, temperature rise and stress induced by high intense photon beam in the rotated titanium-alloy target have been estimated. The maximal thermal stress in the target is about 224 MPa for the source with photon collimation to achieve a positron polarization of 54%.

physics.acc-ph↗

arXiv2012

Depolarization in the ILC Linac-to-Ring Positron Beamline

To achieve the physics goals of future Linear Colliders, it is important that electron and positron beams are polarized. The positron source planned for the International Linear Collider (ILC) is based on a helical undulator system and can deliver a polarised beam with positron polarization of 60%. To ensure that no significant polarization is lost during the transport of the electron and positron beams from the source to the interaction region, spin tracking has to be included in all transport elements which can contribute to a loss of polarization. These are the positron source, the damping ring, the spin rotators, the main linac and the beam delivery system. In particular, the dynamics of the polarized positron beam is required to be investigated. The results of positron spin tracking and depolarization study at the Positron-Linac-To-Ring (PLTR) beamline are presented.

physics.acc-ph↗