arXiv subjects

Samer Hanna

Publications and source records attributed to Samer Hanna.

17 recordsLinked to original sources

arXiv2022

Distributed Transmit Beamforming: Analyzing the Maximum Communication Range

Distributed transmit beamforming is a technique that adjusts the signals from cooperating radios to combine coherently at a destination radio. To achieve coherent combining, the radios can exchange preambles with the destination for frequency synchronization and signal phase adjustment. At the destination, coherent combining leads to a beamforming (BF) gain. The BF gain can extend the communication range by countering the path loss that increases with the distance from the destination. While ideally the maximum range can be trivially calculated from the BF gain, in reality, the BF gain depends on the distance because, at a larger distance, lower SNR of the exchanged preambles causes higher synchronization and phase estimation errors, which in turn degrades the BF gain. In this paper, considering the BF gain degradation for a destination-led BF protocol, we calculate the maximum communication range to realize a desired post-BF SNR by analyzing the relation between the pre-BF SNR and the BF gain. We show that increasing the preamble lengths or increasing the destination power can significantly increase the maximum range while just increasing the number of radios gives diminishing range extension.

eess.SP↗

arXiv2022

Destination-Feedback Free Distributed Transmit Beamforming using Guided Directionality

Distributed transmit beamforming enables cooperative radios to act as one virtual antenna array, extending their communications' range beyond the capabilities of a single radio. Most existing distributed beamforming approaches rely on the destination radio sending feedback to adjust the transmitters' signals for coherent combining. However, relying on the destination radio's feedback limits the communications range to that of a single radio. Existing destination-feedback-free approaches rely on phase synchronization and knowing the node locations with sub-wavelength accuracy, which becomes impractical for radios mounted on high-mobility platforms like UAVs. In this work, we propose and demonstrate a destination-feedback-free distributed beamforming approach that leverages the radio's mobility and coarse location information in a dominant line-of-sight channel. In the proposed approach, one radio acts as a guide and moves to point the beam of the remaining radios towards the destination. We specify the radios' position requirements and verify their relation to the combined signal at the destination using simulations. A proof of concept demo was implemented using software defined radios, showing up to 9dB SNR improvement in the beamforming direction just by relying on the coarse placement of four radios.

eess.SP↗

arXiv2022

WiSig: A Large-Scale WiFi Signal Dataset for Receiver and Channel Agnostic RF Fingerprinting

RF fingerprinting leverages circuit-level variability of transmitters to identify them using signals they send. Signals used for identification are impacted by a wireless channel and receiver circuitry, creating additional impairments that can confuse transmitter identification. Eliminating these impairments or just evaluating them, requires data captured over a prolonged period of time, using many spatially separated transmitters and receivers. In this paper, we present WiSig; a large scale WiFi dataset containing 10 million packets captured from 174 off-the-shelf WiFi transmitters and 41 USRP receivers over 4 captures spanning a month. WiSig is publicly available, not just as raw captures, but as conveniently pre-processed subsets of limited size, along with the scripts and examples. A preliminary evaluation performed using WiSig shows that changing receivers, or using signals captured on a different day can significantly degrade a trained classifier's performance. While capturing data over more days or more receivers limits the degradation, it is not always feasible and novel data-driven approaches are needed. WiSig provides the data to develop and evaluate these approaches towards channel and receiver agnostic transmitter fingerprinting.

eess.SP↗

arXiv2021

Real-time Wireless Transmitter Authorization: Adapting to Dynamic Authorized Sets with Information Retrieval

As the Internet of Things (IoT) continues to grow, ensuring the security of systems that rely on wireless IoT devices has become critically important. Deep learning-based passive physical layer transmitter authorization systems have been introduced recently for this purpose, as they accommodate the limited computational and power budget of such devices. These systems have been shown to offer excellent outlier detection accuracies when trained and tested on a fixed authorized transmitter set. However in a real-life deployment, a need may arise for transmitters to be added and removed as the authorized set of transmitters changes. In such cases, the system could experience long down-times, as retraining the underlying deep learning model is often a time-consuming process. In this paper, we draw inspiration from information retrieval to address this problem: by utilizing feature vectors as RF fingerprints, we first demonstrate that training could be simplified to indexing those feature vectors into a database using locality sensitive hashing (LSH). Then we show that approximate nearest neighbor search could be performed on the database to perform transmitter authorization that matches the accuracy of deep learning models, while allowing for more than 100x faster retraining. Furthermore, dimensionality reduction techniques are used on the feature vectors to show that the authorization latency of our technique could be reduced to approach that of traditional deep learning-based systems.

cs.LG↗

arXiv2021

Distributed Transmit Beamforming: Design and Demonstration from the Lab to UAVs

Cooperating radios can extend their communication range by adjusting their signals to ensure coherent combining at a destination radio. This technique is called distributed transmit beamforming. Beamforming (BF) relies on the BF radios having frequency synchronized carriers and phases adjusted for coherent combining. Both requirements are typically met by exchanging preambles with the destination. However, since BF aims to increase the communication range, the individually transmitted preambles are typically at low SNR and their lengths are constrained by the channel coherence time. These noisy preambles lead to errors in frequency and phase estimation, which result in randomly changing BF gains. To build reliable distributed BF systems, the impact of estimation errors on the BF gains need to be considered in the design. In this work, assuming a destination-led BF protocol and Kalman filter for frequency tracking, we optimize the number of BF radios and the preamble lengths to achieve reliable BF gain. To do that, we characterize the relations between the BF gains distribution, the channel coherence time, and design parameters like the SNR, preamble lengths, and the number of radios. The proposed relations are verified using simulations and via experiments using software-defined radios in a lab and on UAVs.

eess.SP↗

arXiv2021

Signal Processing Based Deep Learning for Blind Symbol Decoding and Modulation Classification

Blindly decoding a signal requires estimating its unknown transmit parameters, compensating for the wireless channel impairments, and identifying the modulation type. While deep learning can solve complex problems, digital signal processing (DSP) is interpretable and can be more computationally efficient. To combine both, we propose the dual path network (DPN). It consists of a signal path of DSP operations that recover the signal, and a feature path of neural networks that estimate the unknown transmit parameters. By interconnecting the paths over several recovery stages, later stages benefit from the recovered signals and reuse all the previously extracted features. The proposed design is demonstrated to provide 5% improvement in modulation classification compared to alternative designs lacking either feature sharing or access to recovered signals. The estimation results of DPN along with its blind decoding performance are shown to outperform a blind signal processing algorithm for BPSK and QPSK on a simulated dataset. An over-the-air software-defined-radio capture was used to verify DPN results at high SNRs. DPN design can process variable length inputs and is shown to outperform relying on fixed length inputs with prediction averaging on longer signals by up to 15% in modulation classification.

eess.SP↗

arXiv2021

Open Set RF Fingerprinting using Generative Outlier Augmentation

RF devices can be identified by unique imperfections embedded in the signals they transmit called RF fingerprints. The closed set classification of such devices, where the identification must be made among an authorized set of transmitters, has been well explored. However, the much more difficult problem of open set classification, where the classifier needs to reject unauthorized transmitters while recognizing authorized transmitters, has only been recently visited. So far, efforts at open set classification have largely relied on the utilization of signal samples captured from a known set of unauthorized transmitters to aid the classifier learn unauthorized transmitter fingerprints. Since acquiring new transmitters to use as known transmitters is highly expensive, we propose to use generative deep learning methods to emulate unauthorized signal samples for the augmentation of training datasets. We develop two different data augmentation techniques, one that exploits a limited number of known unauthorized transmitters and the other that does not require any unauthorized transmitters. Experiments conducted on a dataset captured from a WiFi testbed indicate that data augmentation allows for significant increases in open set classification accuracy, especially when the authorized set is small.

eess.SP↗

arXiv2021

A Schottky-Diode-Based Wake-Up Receiver for IoT Applications

This paper presents an always-on low-power wake-up receiver (WuRx) that activates the remainder of the system when a wake-up signal is detected. The proposed receiver has two phases of waking up. The first phase uses an integrated CMOS Schottky diodes to detect the signal power at a low bias current. The approach dissipates low quiescent power and allows the reuse of the design in multiple frequency bands with only modifying the matching network. In the second phase, a data-locked startable oscillator is proposed to correlate the received data with a target signature. This design eliminates the area and power dissipation of an external crystal oscillator and only turns on when the second phase is activated. By correlating to a target signature, the second phase also reduces the probability of a false alarm (PFA) that would otherwise wake up the high-power bulk of the system. The two-phase approach leads to significant reduction in average power consumption when compared to a single-phase design. This implementation targets sub-ms wake-up latency and operates in the unlicensed band at a 750-MHz carrier frequency with a data rate of 200 kbps. The design achieves $\sim$8.45pJ/bit and $<$-50 dBm of input sensitivity and average power of 1.69$μ$W. The system is implemented in 65-nm CMOS technology and occupies an area of 1mm$\times$0.75mm.

eess.SP↗

arXiv2021

UAV Swarm Position Optimization for High Capacity MIMO Backhaul

A swarm of cooperating UAVs communicating with a distant multiantenna ground station can leverage MIMO spatial multiplexing to scale the capacity. Due to the line-of-sight propagation between the swarm and the ground station, the MIMO channel is highly correlated, leading to limited multiplexing gains. In this paper, we optimize the UAV positions to attain the maximum MIMO capacity given by the single user bound. An infinite set of UAV placements that attains the capacity bound is first derived. Given an initial swarm placement, we formulate the problem of minimizing the distance traveled by the UAVs to reach a placement within the capacity maximizing set of positions. An offline centralized solution to the problem using block coordinate descent is developed assuming known initial positions of UAVs. We also propose an online distributed algorithm, where the UAVs iteratively adjust their positions to maximize the capacity. Our proposed approaches are shown to significantly increase the capacity at the expense of a bounded translation from the initial UAV placements. This capacity increase persists when using a massive MIMO ground station. Using numerical simulations, we show the robustness of our approaches in a Rician channel under UAV motion disturbances.

eess.SP↗

arXiv2020

Spatial Signal Strength Prediction using 3D Maps and Deep Learning

Machine learning (ML) and artificial neural networks (ANNs) have been successfully applied to simulating complex physics by learning physics models thanks to large data. Inspired by the successes of ANNs in physics modeling, we use deep neural networks (DNNs) to predict the radio signal strength field in an urban environment. Our algorithm relies on samples of signal strength collected across the prediction space and a 3D map of the environment, which enables it to predict the scattering of radio waves through the environment. While already extensive body of research exists in spatial signal strength prediction, our approach differs from most existing approaches in that it does not require the knowledge of the transmitter location, it does not require side channel information such as attenuation and shadowing parameters, and it is the first work, to the best of our knowledge, to use 3D maps to accomplish the task of signal strength prediction. This algorithm is developed for the purpose of placement optimization of a UAV or mobile robot to maximize the signal strength to or from a stationary transceiver but it also holds relevance to dynamic spectrum access networks, cellular coverage design, power control algorithms, etc.

eess.SP↗

arXiv2020

Combining Deep Learning and Linear Processing for Modulation Classification and Symbol Decoding

Deep learning has been recently applied to many problems in wireless communications including modulation classification and symbol decoding. Many of the existing end-to-end learning approaches demonstrated robustness to signal distortions like frequency and timing errors, and outperformed classical signal processing techniques with sufficient training. However, deep learning approaches typically require hundreds of thousands of floating points operations for inference, which is orders of magnitude higher than classical signal processing approaches and thus do not scale well for long sequences. Additionally, they typically operate as a black box and without insight on how their final output was obtained, they can't be integrated with existing approaches. In this paper, we propose a novel neural network architecture that combines deep learning with linear signal processing typically done at the receiver to realize joint modulation classification and symbol recovery. The proposed method estimates signal parameters by learning and corrects signal distortions like carrier frequency offset and multipath fading by linear processing. Using this hybrid approach, we leverage the power of deep learning while retaining the efficiency of conventional receiver processing techniques for long sequences. The proposed hybrid approach provides good accuracy in signal distortion estimation leading to promising results in terms of symbol error rate. For modulation classification accuracy, it outperforms many state of the art deep learning networks.

eess.SP↗

arXiv2020

Deep Learning Approaches for Open Set Wireless Transmitter Authorization

Wireless signals contain transmitter specific features, which can be used to verify the identity of transmitters and assist in implementing an authentication and authorization system. Most recently, there has been wide interest in using deep learning for transmitter identification. However, the existing deep learning work has posed the problem as closed set classification, where a neural network classifies among a finite set of known transmitters. No matter how large this set is, it will not include all transmitters that exist. Malicious transmitters outside this closed set, once within communications range, can jeopardize the system security. In this paper, we propose a deep learning approach for transmitter authorization based on open set recognition. Our proposed approach identifies a set of authorized transmitters, while rejecting any other unseen transmitters by recognizing their signals as outliers. We propose three approaches for this problem and show their ability to reject signals from unauthorized transmitters on a dataset of WiFi captures. We consider the structure of training data needed, and we show that the accuracy improves by having signals from known unauthorized transmitters in the training set.

eess.SP↗

arXiv2020

Open Set Wireless Transmitter Authorization: Deep Learning Approaches and Dataset Considerations

Due to imperfections in transmitters' hardware, wireless signals can be used to verify their identity in an authorization system. While deep learning was proposed for transmitter identification, the majority of the work has focused on classification among a closed set of transmitters. Malicious transmitters outside this closed set will be misclassified, jeopardizing the authorization system. In this paper, we consider the problem of recognizing authorized transmitters and rejecting new transmitters. To address this problem, we adapt the most prominent approaches from the open set recognition and anomaly detection literature to the problem. We study how these approaches scale with the required number of authorized transmitters. We propose using a known set of unauthorized transmitters to assist the training and study its impact. The evaluation procedure takes into consideration that some transmitters might be more similar than others and nuances these effects. The robustness of the RF authorization with respect to temporal changes in fingerprints is also considered in the evaluation. When using 10 authorized and 50 known unauthorized WiFi transmitters from a publicly accessible testbed, we were able to achieve an outlier detection accuracy of 98% on the same day test set and 80% on the different day test set.

eess.SP↗

arXiv2019

UAV Access Point Placement for Connectivity to a User with Unknown Location Using Deep RL

In recent years, unmanned aerial vehicles (UAVs) have been considered for telecommunications purposes as relays, caches, or IoT data collectors. In addition to being easy to deploy, their maneuverability allows them to adjust their location to optimize the capacity of the link to the user equipment on the ground or of the link to the basestation. The majority of the previous work that analyzes the optimal placement of such a UAV makes at least one of two assumptions: the channel can be predicted using a simple model or the locations of the users on the ground are known. In this paper, we use deep reinforcement learning (deep RL) to optimally place a UAV serving a ground user in an urban environment, without the previous knowledge of the channel or user location. Our algorithm relies on signal-to-interference-plus-noise ratio (SINR) measurements and a 3D map of the topology to account for blockage and scatterers. Furthermore, it is designed to operate in any urban environment. Results in conditions simulated by a ray tracing software show that with the constraint on the maximum number of iterations our algorithm has a 90% success rate in converging to a target SINR.

eess.SP↗

arXiv2019

UAV Swarms as Amplify-and-Forward MIMO Relays

Unmanned aerial vehicles provide new opportunities for performance improvements in future wireless communications systems. For example, they can act as relays that extend the range of a communication link and improve the capacity. Unlike conventional relays that are deployed at fixed locations, UAVs can change their positions to optimize the capacity or range on demand. In this paper, we consider using a swarm of UAVs as amplify-and-forward MIMO relays to provide connectivity between an obstructed multi-antenna equipped source and destination. We start by optimizing UAV placement for the single antenna case, and analyze its dependence on the noise introduced by the relay, its gain, and transmit power constraint. We extend our analysis for an arbitrary UAV swarm and show how the MIMO link capacity can be optimized by changing the distance of the swarm to the source and the destination. Then, we consider the effect of optimizing the positions of the UAVs within the swarm and derive an upper bound for the capacity at any given placement of the swarm. We also propose a simple near optimal approach to find the positions that optimize the capacity for the end-to-end link given that the source and the destination have uniform rectangular arrays.

eess.SP↗

arXiv2018

Distributed UAV Placement Optimization for Cooperative Line-of-Sight MIMO Communications

Cooperative communication using unmanned aerial vehicles (UAVs) is a promising technology for infrastructureless wireless networks. One of the key challenges in UAV based communications is the backhaul throughput. In this paper, we propose optimization of the UAV swarm positions to achieve a high mulitplexing gain in line-of-sight (LoS) MIMO backhaul. We develop two distributed algorithms to position the UAVs such that each UAV moves a minimal distance to realize the highest capacity LoS MIMO channel. The first approach uses iterative gradient descent (GD) and the second uses iterative brute force (BF). Simulations show that both algorithms can achieve up to 6 times higher capacity compared to the approach relying on random UAV placement, earlier proposed in the literature. BF has the advantage of not requiring any location information, while GD is less sensitive to errors in motion.

eess.SP↗

arXiv2018

Software Defined Radio Implementation of Carrier and Timing Synchronization for Distributed Arrays

The communication range of wireless networks can be greatly improved by using distributed beamforming from a set of independent radio nodes. One of the key challenges in establishing a beamformed communication link from separate radios is achieving carrier frequency and sample timing synchronization. This paper describes an implementation that addresses both carrier frequency and sample timing synchronization simultaneously using RF signaling between designated master and slave nodes. By using a pilot signal transmitted by the master node, each slave estimates and tracks the frequency and timing offset and digitally compensates for them. A real-time implementation of the proposed system was developed in GNU Radio and tested with Ettus USRP N210 software defined radios. The measurements show that the distributed array can reach a residual frequency error of 5 Hz and a residual timing offset of 1/16 the sample duration for 70 percent of the time. This performance enables distributed beamforming for range extension applications.

eess.SP↗