arXiv subjects

Samuel Deléglise

Publications and source records attributed to Samuel Deléglise.

13 recordsLinked to original sources

arXiv2026

Cryogenic rf-to-microwave transducer based on a dc-biased electromechanical system

We report a two-stage, heterodyne rf-to-microwave transducer that combines a tunable electrostatic pre-amplifier with a superconducting electromechanical cavity. A metalized Si$_3$N$_4$ membrane (3 MHz frequency) forms the movable plate of a vacuum-gap capacitor in a microwave LC resonator. A dc bias across the gap converts any small rf signal into a resonant electrostatic force proportional to the bias, providing a voltage-controlled gain that multiplies the cavity's intrinsic electromechanical gain. In a flip-chip device with a 1.5 $\mathrmμ$m gap operated at 10 mK we observe dc-tunable anti-spring shifts, and rf-to-microwave transduction at 49 V bias, achieving a charge sensitivity of 87 $\mathrmμ$e/$\sqrt{\mathrm{Hz}}$ (0.9 nV/$\sqrt{\mathrm{Hz}}$). Extrapolation to sub-micron gaps and state-of-the-art $Q>10^8$ membrane resonators predicts sub-200 fV/$\sqrt{\mathrm{Hz}}$ sensitivity, establishing dc-biased electromechanics as a practical route towards quantum-grade rf electrometers and low-noise modular heterodyne links for superconducting microwave circuits and charge or voltage sensing.

quant-ph↗

arXiv2026

Probing the quantum motion of a macroscopic mechanical oscillator with a radio-frequency superconducting qubit

Long-lived mechanical resonators like drums oscillating at MHz frequencies and operating in the quantum regime are a powerful platform for quantum technologies and tests of fundamental physics. Yet, quantum control of such systems remains challenging, owing to their low energy scale and the difficulty of achieving efficient coupling to other well-controlled quantum devices. Here, we demonstrate repeated coherent interactions between a 4 MHz suspended silicon nitride membrane and a resonant superconducting heavy-fluxonium qubit. The qubit is initialized at an effective temperature of $21~\mathrm{μK}$ and read out with 77% single-shot fidelity. During the $6~\mathrm{ms}$ lifetime of the membrane the two systems swap excitations more than 300 times. After each interaction, a state-selective qubit detection is performed, implementing a stroboscopic series of weak measurements that provide information about the mechanical state. The accumulated records reconstruct the position noise spectrum of the membrane, revealing both its thermal occupation $n_\mathrm{th}\approx47$ at $10~\mathrm{mK}$ and the qubit-induced back-action. By preparing the qubit either in its ground or excited state before each interaction, we observe an imbalance between the emission and absorption spectra, proportional to $n_\mathrm{th}$ and $n_\mathrm{th}+1$, respectively-a hallmark of the non-commutation of phonon creation and annihilation operators. Since the predicted Diósi-Penrose gravitational collapse time is comparable to the measured mechanical decoherence time, our architecture enters a regime where gravity-induced decoherence could be tested directly.

quant-ph↗

arXiv2025

Hyperinductance based on stacked Josephson junctions

Superinductances are superconducting circuit elements that combine a large inductance with a low parasitic capacitance to ground, resulting in a characteristic impedance exceeding the resistance quantum $R_Q = h/(2e)^2 \simeq 6.45 \mathrm{k}Ω$. In recent years, these components have become key enablers for emerging quantum circuit architectures. However, achieving high characteristic impedance while maintaining scalability and fabrication robustness remains a major challenge. In this work, we present two fabrication techniques for realizing superinductances based on vertically stacked Josephson junctions. Using a multi-angle Manhattan (MAM) process and a zero-angle (ZA) evaporation technique -- in which junction stacks are connected pairwise using airbridges -- we fabricate one-dimensional chains of stacks that act as high-impedance superconducting transmission lines. Two-tone microwave spectroscopy reveals the expected $\sqrt{n}$ scaling of the impedance with the number of junctions per stack. The chain fabricated using the ZA process, with nine junctions per stack, achieves a characteristic impedance of $\sim 16 \mathrm{k}Ω$, a total inductance of $5.9 \mathrm{μH}$, and a maximum frequency-dependent impedance of $50 \mathrm{k}Ω$ at 1.4 GHz. Our results establish junction stacking as a scalable, robust, and flexible platform for next-generation quantum circuits requiring ultra-high impedance environments.

quant-ph↗

arXiv2025

Enhancing dissipative cat qubit protection by squeezing

Dissipative cat-qubits are a promising architecture for quantum processors due to their built-in quantum error correction. By leveraging two-photon stabilization, they achieve an exponentially suppressed bit-flip error rate as the distance in phase-space between their basis states increases, incurring only a linear increase in phase-flip rate. This property substantially reduces the number of qubits required for fault-tolerant quantum computation. Here, we implement a squeezing deformation of the cat qubit basis states, further extending the bit-flip time while minimally affecting the phase-flip rate. We demonstrate a steep reduction in the bit-flip error rate with increasing mean photon number, characterized by a scaling exponent $γ=4.3$, rising by a factor of 74 per added photon. Specifically, we measure bit-flip times of 22 seconds for a phase-flip time of 1.3 $μ$s in a squeezed cat qubit with an average photon number $\bar{n}=4.1$, a 160-fold improvement in bit-flip time compared to a standard cat. Moreover, we demonstrate a two-fold reduction in $Z$-gate infidelity, with an estimated phase-flip probability of $ε_X = 0.085$ and a bit-flip probability of $ε_Z = 2.65 \cdot 10^{-9}$ which confirms the gate bias-preserving property. This simple yet effective technique enhances cat qubit performances without requiring design modification, moving multi-cat architectures closer to fault-tolerant quantum computation.

quant-ph↗

arXiv2023

FPGA-based feedback control of quantum optics experiments with the open source software package PyRPL

We present PyRPL, an open source software package that allows the implementation of automatic digital feedback controllers for quantum optics experiments on commercially available, affordable FPGA boards. Our software implements the digital generation of various types of error signals, from an analog input through the application of loop filters of high complexity and real-time gain adjustment for multiple analog output signals, including different algorithms for resonance search, lock acquisition sequences and in-loop gain optimization. Furthermore, all necessary diagnostic instruments such as an oscilloscope, a network analyzer and a spectrum analyzer are integrated into our software. Apart from providing a quickly scalable, automatic feedback controller, the lock performance that can be achieved by using PyRPL with imperfect equipment such as piezoelectric transducers and noisy amplifiers is better than the one achievable with standard analog controllers due to the higher complexity of implementable filters and possibilities of nonlinear operations in the FPGA. This drastically reduces the cost of added complexity when introducing additional feedback loops to an experiment. The open-source character also distinguishes PyRPL from commercial solutions, as it allows users to customize functionalities at various levels, ranging from the easy integration of PyRPL-based feedback controllers into existing setups to the modification of the FPGA functionality. A community of developers provides fast and efficient implementation and testing of software modifications.

quant-ph↗

arXiv2019

Detecting itinerant microwave photons with engineered non-linear dissipation

Single photon detection is a key resource for sensing at the quantum limit and the enabling technology for measurement based quantum computing. Photon detection at optical frequencies relies on irreversible photo-assisted ionization of various natural materials. However, microwave photons have energies 5 orders of magnitude lower than optical photons, and are therefore ineffective at triggering measurable phenomena at macroscopic scales. Here, we report the observation of a new type of interaction between a single two level system (qubit) and a microwave resonator. These two quantum systems do not interact coherently, instead, they share a common dissipative mechanism to a cold bath: the qubit irreversibly switches to its excited state if and only if a photon enters the resonator. We have used this highly correlated dissipation mechanism to detect itinerant photons impinging on the resonator. This scheme does not require any prior knowledge of the photon waveform nor its arrival time, and dominant decoherence mechanisms do not trigger spurious detection events (dark counts). We demonstrate a detection efficiency of 58% and a record low dark count rate of 1.4 per ms. This work establishes engineered non-linear dissipation as a key-enabling resource for a new class of low-noise non-linear microwave detectors.

quant-ph↗

arXiv2018

Adiabatic elimination for multi-partite open quantum systems with non-trivial zero-order dynamics

We provide model reduction formulas for open quantum systems consisting of a target component which weakly interacts with a strongly dissipative environment. The time-scale separation between the uncoupled dynamics and the interaction allows to employ tools from center manifold theory and geometric singular perturbation theory to eliminate the variables associated to the environment (adiabatic elimination) with high-order accuracy. An important specificity is to preserve the quantum structure: reduced dynamics in (positive) Lindblad form and coordinate mappings in Kraus form. We provide formulas of the reduced dynamics. The main contributions of this paper are (i) to show how the decomposition of the environment into $K$ components enables its efficient treatment, avoiding the quantum curse of dimension; and (ii) to extend the results to the case where the target component is subject to Hamiltonian evolution at the fast time-scale. We apply our theory to a microwave superconducting quantum resonator subject to material losses, and we show that our reduced-order model can explain the transmission spectrum observed in a recent pump probe experiment.

quant-ph↗

arXiv2016

High-finesse Fabry-Perot cavities with bidimensional Si$_3$N$_4$ photonic-crystal slabs

Light scattering by a two-dimensional photonic crystal slab (PCS) can result in dramatic interference effects associated with Fano resonances. Such devices offer appealing alternatives to distributed Bragg reflectors or filters for various applications such as optical wavelength and polarization filters, reflectors, semiconductor lasers, photodetectors, bio-sensors, or non-linear optical components. Suspended PCSs also find natural applications in the field of optomechanics, where the mechanical modes of a suspended slab interact via radiation pressure with the optical field of a high finesse cavity. The reflectivity and transmission properties of a defect-free suspended PCS around normal incidence can be used to couple out-of-plane mechanical modes to an optical field by integrating it in a free space cavity. Here, we demonstrate the successful implementation of a PCS reflector on a high-tensile stress Si$_3$N$_4$ nanomembrane. We illustrate the physical process underlying the high reflectivity by measuring the photonic crystal band diagram. Moreover, we introduce a clear theoretical description of the membrane scattering properties in the presence of optical losses. By embedding the PCS inside a high-finesse cavity, we fully characterize its optical properties. The spectrally, angular, and polarization resolved measurements demonstrate the wide tunability of the membrane's reflectivity, from nearly 0 to 99.9470~$\pm$ 0.0025 \%, and show that material absorption is not the main source of optical loss. Moreover, the cavity storage time demonstrated in this work exceeds the mechanical period of low-order mechanical drum modes. This so-called resolved sideband condition is a prerequisite to achieve quantum control of the mechanical resonator with light.

quant-ph↗

arXiv2016

A new method of probing mechanical losses of coatings at cryogenic temperatures

A new method of probing mechanical losses and comparing the corresponding deposition processes of metallic and dielectric coatings in 1-100 MHz frequency range and cryogenic temperatures is presented. The method is based on the use of extremely high-quality quartz acoustic cavities whose internal losses are orders of magnitude lower than any available coatings nowadays. The approach is demonstrated for Chromium, Chromium/Gold and a multilayer tantala/silica coatings. The ${\rm Ta}_2{\rm O}_5/{\rm Si}{\rm O}_2$ coating has been found to exhibit a loss angle lower than $1.6\times10^{-5}$ near 30 {\rm MHz} at 4 {\rm K}. The results are compared to the previous measurements.

physics.ins-det↗

arXiv2008

Freezing a Coherent Field Growth in a Cavity by Quantum Zeno Effect

We have frozen the coherent evolution of a field in a cavity by repeated measurements of its photon number. We use circular Rydberg atoms dispersively coupled to the cavity mode for an absorption-free photon counting. These measurements inhibit the growth of a Field injected in the cavity by a classical source. This manifestation of the Quantum Zeno effect illustrates the back action of the photon number determination onto the Field phase. The residual growth of the Field can be seen as a random walk of its amplitude in the two-dimensional phase space. This experiment sheds light onto the measurement process and opens perspectives for active quantum feedback.

quant-ph↗

arXiv2007

Progressive field-state collapse and quantum non-demolition photon counting

The irreversible evolution of a microscopic system under measurement is a central feature of quantum theory. From an initial state generally exhibiting quantum uncertainty in the measured observable, the system is projected into a state in which this observable becomes precisely known. Its value is random, with a probability determined by the initial system's state. The evolution induced by measurement (known as 'state collapse') can be progressive, accumulating the effects of elementary state changes. Here we report the observation of such a step-by-step collapse by measuring non-destructively the photon number of a field stored in a cavity. Atoms behaving as microscopic clocks cross the cavity successively. By measuring the light-induced alterations of the clock rate, information is progressively extracted, until the initially uncertain photon number converges to an integer. The suppression of the photon number spread is demonstrated by correlations between repeated measurements. The procedure illustrates all the postulates of quantum measurement (state collapse, statistical results and repeatability) and should facilitate studies of non-classical fields trapped in cavities.

quant-ph↗

arXiv2007

Ultrahigh finesse Fabry-Perot superconducting resonator

We have built a microwave Fabry-Perot resonator made of diamond-machined copper mirrors coated with superconducting niobium. Its damping time (Tc = 130 ms at 51 GHz and 0.8 K) corresponds to a ﬁnesse of 4.6 x 109, the highest ever reached for a Fabry-Perot in any frequency range. This result opens novel perspectives for quantum information, decoherence and non-locality studies.

quant-ph↗

arXiv2007

Quantum jumps of light recording the birth and death of a photon in a cavity

A microscopic system under continuous observation exhibits at random times sudden jumps between its states. The detection of this essential quantum feature requires a quantum non-demolition (QND) measurement repeated many times during the system evolution. Quantum jumps of trapped massive particles (electrons, ions or molecules) have been observed, which is not the case of the jumps of light quanta. Usual photodetectors absorb light and are thus unable to detect the same photon twice. They must be replaced by a transparent counter 'seeing' photons without destroying them3. Moreover, the light has to be stored over a duration much longer than the QND detection time. We have fulfilled these challenging conditions and observed photon number quantum jumps. Microwave photons are stored in a superconducting cavity for times in the second range. They are repeatedly probed by a stream of non-absorbing atoms. An atom interferometer measures the atomic dipole phase shift induced by the non-resonant cavity field, so that the final atom state reveals directly the presence of a single photon in the cavity. Sequences of hundreds of atoms highly correlated in the same state, are interrupted by sudden state-switchings. These telegraphic signals record, for the first time, the birth, life and death of individual photons. Applying a similar QND procedure to mesoscopic fields with tens of photons opens new perspectives for the exploration of the quantum to classical boundary.

quant-ph↗