arXiv subjects

Saptarshi Chaudhuri

Publications and source records attributed to Saptarshi Chaudhuri.

At least 19 recordsLinked to original sources

arXiv2026

SQUID Readout of a High-$Q$ Superconducting $LC$ Resonator

We demonstrate the readout of a superconducting $LC$ resonator, with $Q \approx 2 \times 10^{6}$ at approximately 250 kHz, using a dc SQUID followed by a SQUID series-array amplifier readout chain. We find that $Q$ depends on the SQUID flux-bias point, increasing near the shallow-slope point of the SQUID modulation curve and decreasing near the steep-slope point, consistent with the previously observed SQUID damping effects. From this variation, we infer the SQUID effective input impedance. We further infer the effective temperature of the resonator circuit from the resonance peak in the noise spectrum and show that it also depends on the SQUID flux-bias point, suggesting a possible contribution from SQUID back-action noise. This system provides a working prototype for future experiments based on lumped-element resonators with SQUID readout, in particular low-mass axion searches within the DMRadio program.

physics.ins-det↗

arXiv2026

High-$Q$ Superconducting Lumped-Element Resonators for Low-Mass Axion Searches

Low-frequency superconducting lumped-element resonators have recently attracted significant attention in the context of axion dark matter searches. Here we present the design and implementation of a fixed-frequency superconducting resonator operating near 250 kHz, possessing an inductor volume of approximately 1 liter and achieving an unloaded quality factor $Q \approx 2.1\times10^{6}$. This resonator represents a significant improvement over the state of the art and informs the design of searches for low-mass axions.

physics.ins-det↗

arXiv2025

Quantum metrology of low frequency electromagnetic modes with frequency upconverters

We present the RF Quantum Upconverter (RQU) and describe its application to quantum metrology of electromagnetic modes between dc and the Very High Frequency band (VHF) ($\lesssim$300MHz). The RQU uses a Josephson interferometer made up of superconducting loops and Josephson junctions to implement a parametric interaction between a low-frequency electromagnetic mode (between dc and VHF) and a mode in the microwave C Band ($\sim$ 5GHz), analogous to the radiation pressure interaction between electromagnetic and mechanical modes in cavity optomechanics. We analyze RQU performance with quantum amplifier theory, and show that the RQU can operate as a quantum-limited op-amp in this frequency range. It can also use non-classical measurement protocols equivalent to those used in cavity optomechanics, including back-action evading (BAE) measurements, sideband cooling, and two-mode squeezing. These protocols enable experiments using dc--VHF electromagnetic modes as quantum sensors with sensitivity better than the Standard Quantum Limit (SQL). We demonstrate signal upconversion from low frequencies to microwave C band using an RQU and show a phase-sensitive gain (extinction ratio) of $46.9$\;dB, which is a necessary step towards the realization of full BAE.

quant-ph↗

arXiv2025

A Near Quantum Limited Sub-GHz TiN Kinetic Inductance Traveling Wave Parametric Amplifier Operating in a Frequency Translating Mode

We present the design and experimental characterization of a kinetic-inductance traveling-wave parametric amplifier (KI-TWPA) for sub-GHz frequencies. KI-TWPAs amplify signals through nonlinear mixing processes supported by the nonlinear kinetic inductance of a superconducting transmission line. The device described here utilizes a compactly meandered TiN microstrip transmission line to achieve the length needed to amplify sub-GHz signals. It is operated in a frequency translating mode where the amplified signal tone is terminated at the output of the amplifier, and the idler tone at approximately 2.5~GHz is brought out of the cryostat. By varying the pump frequency, a gain of up to 22 dB was achieved in a tunable range from about 450 to 850~MHz. Use of TiN as the nonlinear element allows for a reduction of the required pump power by roughly an order of magnitude relative to NbTiN, which has been used for previous KI-TWPA implementations. This amplifier has the potential to enable high-sensitivity and high-speed measurements in a wide range of applications, such as quantum computing, astrophysics, and dark matter detection.

quant-ph↗

arXiv2022

Generalised Mathematical Formulations for Non-Linear Optimized Scheduling

In practice, most of the optimization problems are non-linear requiring certain interactive solutions and approaches to model. In 5G Advanced and Beyond network slicing, mathematically modeling the users, type of service distributions and its adaptive SLAs are complex due to several dependencies. To facilitate the above, in this paper, we present novel Non-linear mathematical formulations and results that will form the base to achieve Optimized Scheduling.

cs.NI↗

arXiv2021

Impedance Matching to Axion Dark Matter: Considerations of the Photon-Electron Interaction

We introduce the concept of impedance matching to axion dark matter by posing the question of why axion detection is difficult, even though there is enough power in each square meter of incident dark-matter flux to energize a LED light bulb. By quantifying backreaction on the axion field, we show that a small axion-photon coupling does not by itself prevent an order-unity fraction of the dark matter from being absorbed through optimal impedance match. We further show, in contrast, that the electromagnetic charges and the self-impedance of their coupling to photons provide the principal constraint on power absorption integrated across a search band. Using the equations of axion electrodynamics, we demonstrate stringent limitations on absorbed power in linear, time-invariant, passive receivers. Our results yield fundamental constraints, arising from the photon-electron interaction, on improving integrated power absorption beyond the cavity haloscope technique. The analysis also has significant practical implications, showing apparent tension with the sensitivity projections for a number of planned axion searches. We additionally provide a basis for more accurate signal power calculations and calibration models, especially for receivers using multi-wavelength open configurations such as dish antennas and dielectric haloscopes.

hep-ph↗

arXiv2021

Predictive Dynamic Scaling Multi-Slice-in-Slice-Connected Users for 5G System Resource Scheduling

Network slicing is an effective 5G concept for improved resource utilization and service scalability tailored to users (UEs) requirements. According to the standardization, 5G system should support UEs through specification of its heterogenous requirements such as, high data rates, traffic density, latency, reliability, UE density, system efficiency and service availability. These requirements are specified as Service Level Agreements (SLAs) between UEs and network operators resulting in increased interest to develop novel challenging mechanisms for improved interference-free resource efficient performances. An emerging concept that enables such demanding SLA assurances is Open-Radio Access Network (O-RAN). In this paper, we study a novel resource scheduling problem for UE services conditioned on other services in network slicing. To improve system performance, we propose that UEs are connected across network slices to serve several applications. UEs of similar service classes (defined by SLAs) are grouped to form optimized slice-in-slice category(s) within network slice(s).We propose novel Predictive Dynamic Scaling Multi-UE service specific System Resource Optimized Scheduling (DMUSO) algorithm(s). Multiobjective multi-constraint optimization problems (MOP) are formed to learn the dynamic system resource allocation and throughput for UE services conditioned on new services entering the network slice. An epsilon-constraint line search algorithm is presented to estimate UE service bandwidth. Using the theoretical models, DMUSO forms optimal slice-in-slice categories and estimates the maximum dynamic additional slice-in-slice categories, throughput served across network slices. Finally, compared to state-of-the-art literatures, DMUSO guarantees UEs SLAs with 4.4 and 7.5 times performance gains

cs.NI↗

arXiv2021

Optimization Results for 5G Slice-in-Slice Scheduling

Open Radio Access Network (ORAN) Slicing for 5G and Beyond is an emerging architecture and feature that will facilitate challenging RAN Service Level Agreement (SLA) assurance targets. This could pave the way for operators to realize the benefits of network slicing efficiently. In this paper, we provide novel and detailed optimization results to achieve Slice-in-Slice Scheduling for 5G User Services in ORAN slicing.

cs.NI↗

arXiv2021

Optimal Impedance Matching and Quantum Limits of Electromagnetic Axion and Hidden-Photon Dark Matter Searches

For the first time, we determine the properties of the optimal single-moded, linear, passive search for electromagnetic coupling to axion and hidden-photon dark matter, subject to the Standard Quantum Limit on phase-insensitive amplification. We establish the parameters that must be considered to determine the optimal search: the impedance match to dark matter; receiver frequency-response and tuning; irreducible noise sources; and prior information on the dark-matter signal. Using complex-power flow equations, we identify two categories of coupling to the dark-matter signal: radiative and reactive. We motivate a focus on single-moded reactive couplings, as receivers using solely radiative couplings are limited in sensitivity by mismatch with the dark-matter source impedance. We define integrated sensitivity as a figure of merit in comparing searches over a wide frequency range and show that the Bode-Fano criterion sets a limit on integrated sensitivity in a reactively coupled receiver. We examine single-pole resonators, a broadly used form of reactive coupling, and show that when thermal noise dominates amplifier noise and noise matching is optimized, substantial sensitivity is available away from the resonator bandwidth. The Bode-Fano constraint establishes the single-pole resonator as near-ideal for single-moded dark-matter detection. Additionally, the optimized resonator is superior to the optimized reactive broadband receiver at all frequencies at which a resonator may practically be made. We optimize time allocation in a tunable resonator search using priors and derive quantum limits on resonant search sensitivity. At low frequencies, the application of our optimization may enhance scan rates by a few orders of magnitude. While our results broadly inform laboratory searches for light fields, they are the basis for DMRadio, a DOE-funded program in axion and hidden-photon detection.

hep-ph↗

arXiv2021

Optimal Electromagnetic Searches for Axion and Hidden-Photon Dark Matter

Direct-detection searches for axions and hidden photons are playing an increasingly prominent role in the search for dark matter. In this work, we derive the properties of optimal electromagnetic searches for these candidates, subject to the Standard Quantum Limit (SQL) on amplification. We show that a single-pole resonant search may possess substantial sensitivity outside of the resonator bandwidth and that optimizing this sensitivity may increase scan rates by up to five orders of magnitude at low frequencies. Additional enhancements can be obtained with resonator quality factors exceeding one million, which corresponds to the linewidth of the dark matter signal. We present the resonator optimization in the broader context of determining the optimal receiver architecture (resonant or otherwise). We discuss prior probabilities on the dark matter signal and their role in the search optimization. We determine frequency-integrated sensitivity to be the figure of merit in a wideband search and demonstrate that it is limited by the Bode-Fano criterion. The optimized single-pole resonator is approximately 75% of the Bode-Fano limit, establishing it as a fundamentally near-ideal, single-moded dark matter detection scheme. Our analysis shows, in contrast to previous work, that the scanned single-pole resonant search is superior to a reactive broadband search. Our results motivate the broad application of quantum measurement techniques evading the SQL in future axion and hidden-photon dark matter searches.

hep-ex↗

arXiv2020

Microwave multiplexing on the Keck Array

We describe an on-sky demonstration of a microwave-multiplexing readout system in one of the receivers of the Keck Array, a polarimetry experiment observing the cosmic microwave background at the South Pole. During the austral summer of 2018-2019, we replaced the time-division multiplexing readout system with microwave-multiplexing components including superconducting microwave resonators coupled to radio-frequency superconducting quantum interference devices at the sub-Kelvin focal plane, coaxial-cable plumbing and amplification between room temperature and the cold stages, and a SLAC Microresonator Radio Frequency system for the warm electronics. In the range 5-6 GHz, a single coaxial cable reads out 528 channels. The readout system is coupled to transition-edge sensors, which are in turn coupled to 150-GHz slot-dipole phased-array antennas. Observations began in April 2019, and we report here on an initial characterization of the system performance.

astro-ph.IM↗

arXiv2018

Highly-multiplexed microwave SQUID readout using the SLAC Microresonator Radio Frequency (SMuRF) Electronics for Future CMB and Sub-millimeter Surveys

The next generation of cryogenic CMB and submillimeter cameras under development require densely instrumented sensor arrays to meet their science goals. The readout of large numbers ($\sim$10,000--100,000 per camera) of sub-Kelvin sensors, for instance as proposed for the CMB-S4 experiment, will require substantial improvements in cold and warm readout techniques. To reduce the readout cost per sensor and integration complexity, efforts are presently focused on achieving higher multiplexing density while maintaining readout noise subdominant to intrinsic detector noise. Highly-multiplexed cold readout technologies in active development include Microwave Kinetic Inductance Sensors (MKIDs) and microwave rf-SQUIDs. Both exploit the high quality factors of superconducting microwave resonators to densely channelize sub-Kelvin sensors into the bandwidth of a microwave transmission line. We present advancements in the development of a new warm readout system for microwave SQUID multiplexing, the SLAC Superconducting Microresonator RF electronics, or SMuRF. The SMuRF system is unique in its ability to track each tone, minimizing the total RF power required to read out each resonator, thereby significantly reducing the linearity requirements on the cold and warm readout. Here, we present measurements of the readout noise and linearity of the first full SMuRF system, including a demonstration of closed-loop tone tracking on a 528 channel cryogenic microwave SQUID multiplexer. SMuRF is being explored as a potential readout solution for several future CMB projects including Simons Observatory, BICEP Array, CCAT-prime, Ali-CPT, and CMB-S4. Parallel development of the platform is underway to adapt SMuRF to read out both MKID and fast X-ray TES calorimeter arrays.

astro-ph.IM↗

arXiv2017

Broadband parametric amplifiers based on nonlinear kinetic inductance artificial transmission lines

We present broadband parametric amplifiers based on the kinetic inductance of superconducting NbTiN thin films in an artificial (lumped-element) transmission line architecture. We demonstrate two amplifier designs implementing different phase matching techniques: periodic impedance loadings, and resonator phase shifters placed periodically along the transmission line. Our design offers several advantages over previous CPW-based amplifiers, including intrinsic 50 ohm characteristic impedance, natural suppression of higher pump harmonics, lower required pump power, and shorter total trace length. Experimental realizations of both versions of the amplifiers are demonstrated. With a transmission line length of 20 cm, we have achieved gains of 15 dB over several GHz of bandwidth.

quant-ph↗

arXiv2016

Design Overview of the DM Radio Pathfinder Experiment

We introduce the DM Radio, a dual search for axion and hidden photon dark matter using a tunable superconducting lumped-element resonator. We discuss the prototype DM Radio Pathfinder experiment, which will probe hidden photons in the 500 peV (100 kHz)-50 neV (10 MHz) mass range. We detail the design of the various components: the LC resonant detector, the resonant frequency tuning procedure, the differential SQUID readout circuit, the shielding, and the cryogenic mounting structure. We present the current status of the pathfinder experiment and illustrate its potential science reach in the context of the larger experimental program.

astro-ph.IM↗

arXiv2016

Dark Sectors 2016 Workshop: Community Report

This report, based on the Dark Sectors workshop at SLAC in April 2016, summarizes the scientific importance of searches for dark sector dark matter and forces at masses beneath the weak-scale, the status of this broad international field, the important milestones motivating future exploration, and promising experimental opportunities to reach these milestones over the next 5-10 years.

hep-ph↗

arXiv2016

Readout of two-kilopixel transition-edge sensor arrays for Advanced ACTPol

Advanced ACTPol is an instrument upgrade for the six-meter Atacama Cosmology Telescope (ACT) designed to measure the cosmic microwave background (CMB) temperature and polarization with arcminute-scale angular resolution. To achieve its science goals, Advanced ACTPol utilizes a larger readout multiplexing factor than any previous CMB experiment to measure detector arrays with approximately two thousand transition-edge sensor (TES) bolometers in each 150 mm detector wafer. We present the implementation and testing of the Advanced ACTPol time-division multiplexing readout architecture with a 64-row multiplexing factor. This includes testing of individual multichroic detector pixels and superconducting quantum interference device (SQUID) multiplexing chips as well as testing and optimizing of the integrated readout electronics. In particular, we describe the new automated multiplexing SQUID tuning procedure developed to select and optimize the thousands of SQUID parameters required to readout each Advanced ACTPol array. The multichroic detector pixels in each array use separate channels for each polarization and each of the two frequencies, such that four TESes must be read out per pixel. Challenges addressed include doubling the number of detectors per multiplexed readout channel compared to ACTPol and optimizing the Nyquist inductance to minimize detector and SQUID noise aliasing.

astro-ph.IM↗

arXiv2015

A Radio for Hidden-Photon Dark Matter Detection

We propose a resonant electromagnetic detector to search for hidden-photon dark matter over an extensive range of masses. Hidden-photon dark matter can be described as a weakly coupled "hidden electric field," oscillating at a frequency fixed by the mass, and able to penetrate any shielding. At low frequencies (compared to the inverse size of the shielding), we find that observable effect of the hidden photon inside any shielding is a real, oscillating magnetic field. We outline experimental setups designed to search for hidden-photon dark matter, using a tunable, resonant LC circuit designed to couple to this magnetic field. Our "straw man" setups take into consideration resonator design, readout architecture and noise estimates. At high frequencies,there is an upper limit to the useful size of a single resonator set by $1/ν$. However, many resonators may be multiplexed within a hidden-photon coherence length to increase the sensitivity in this regime. Hidden-photon dark matter has an enormous range of possible frequencies, but current experiments search only over a few narrow pieces of that range. We find the potential sensitivity of our proposal is many orders of magnitude beyond current limits over an extensive range of frequencies, from 100 Hz up to 700 GHz and potentially higher.

hep-ph↗

arXiv2015

Frequency-tunable Superconducting Resonators via Nonlinear Kinetic Inductance

We have designed, fabricated and tested a frequency-tunable high-Q superconducting resonator made from a niobium titanium nitride film. The frequency tunability is achieved by injecting a DC current through a current-directing circuit into the nonlinear inductor whose kinetic inductance is current-dependent. We have demonstrated continuous tuning of the resonance frequency in a 180 MHz frequency range around 4.5 GHz while maintaining the high internal quality factor $Q_i> 180,000$. This device may serve as a tunable filter and find applications in superconducting quantum computing and measurement. It also provides a useful tool to study the nonlinear response of a superconductor. In addition, it may be developed into techniques for measurement of the complex impedance of a superconductor at its transition temperature and for readout of transition-edge sensors.

cond-mat.supr-con↗