arXiv subjects

Saulius Juodkazis

Publications and source records attributed to Saulius Juodkazis.

At least 55 records · Page 3Linked to original sources

arXiv2018

Kirchhoff's metasurfaces

Thermo-optical properties of the nanodisc and metal hole array plasmonic perfect absorber (PPA) metasurfaces were designed and characterised at midinfrared wavelengths. Both, light emitter and detector systems are highly thought after for the future sensor networks in the internet-of-things for various spectral domains. Reciprocity of the absorbance and emittance is shown experimentally, i.e., the PPAs are following Kirchhoff's law where the patterns exhibiting a strong optical absorption were found enhanced thermal radiation. Design principles and scaling for photo-thermal conversion are discussed. The highest efficiency of light-to-heat and heat-to-radiation were obtained for the Au-Si-Au structures.

physics.optics↗

arXiv2018

Micro-thermocouple on nano-membrane: thermometer for nanoscale measurements

A thermocouple of Au-Ni with only 2.5-micrometers-wide electrodes on a 30-nm-thick Si3N4 membrane was fabricated by a simple low-resolution electron beam lithography and lift off procedure. The thermocouple is shown to be sensitive to heat generated by laser as well as an electron beam. Nano-thin membrane was used to reach a high spatial resolution of energy deposition and to realise a heat source of sub-1 micrometer diameter. This was achieved due to a limited generation of secondary electrons, which increase a lateral energy deposition. A low thermal capacitance of the fabricated devices is useful for the real time monitoring of small and fast temperature changes, e.g., due to convection, and can be detected through an optical and mechanical barrier of the nano-thin membrane. Temperature changes up to ~2x10^5 K/s can be measured at 10 kHz rate. A simultaneous down-sizing of both, the heat detector and heat source strongly required for creation of thermal microscopy is demonstrated. Peculiarities of Seebeck constant (thermopower) dependence on electron injection into thermocouple are discussed. Modeling of thermal flows on a nano-membrane with presence of a micro-thermocouple was carried out to compare with experimentally measured temporal response.

cond-mat.mes-hall↗

arXiv2018

All-dielectric metasurface for wavefront control at terahertz frequencies

Recently, metasurfaces have gained popularity due to their ability to offer a spatially varying phase response, low intrinsic losses and high transmittance. Here, we demonstrate numerically and experimentally a silicon metasurface at THz frequencies that converts a Gaussian beam into a Vortex beam independent of the polarization of the incident beam. The metasurface consists of an array of sub-wavelength silicon cross resonators made of a high refractive index material on substrates such as sapphire and CaF$_2$ that are transparent at IR-THz spectral range. With these substrates, it is possible to create phase elements for a specific spectral range including at the molecular finger printing around 10$~μ$m as well as at longer THz wavelengths where secondary molecular structures can be revealed. This device offers high transmittance and a phase coverage of 0 to $2π$. The transmittance phase is tuned by varying the dimensions of the meta-atoms. To demonstrate wavefront engineering, we used a discretized spiraling phase profile to convert the incident Gaussian beam to vortex beam. To realize this, we divided the metasurface surface into eight angular sectors and chose eight different dimensions for the crosses providing successive phase shifts spaced by $π/4$ radians for each of these sectors. Photolithography and reactive ion etching (RIE) were used to fabricate these silicon crosses as the dimensions of these cylinders range up to few hundreds of micrometers. Large 1-cm-diameter optical elements were successfully fabricated and characterised by optical profilometry.

physics.optics↗

arXiv2017

Engineering the axial intensity of Bessel beams

Bessel beams (BBs) appear immune to diffraction over finite propagation distances due to the conical nature of light propagation along the optical axis. This offers promising advantages in laser fabrication. However, BBs exhibit a significant intensity variation along the direction of propagation. We present a simple technique to engineer the axial intensity of the BB over centimeters-long propagation distances without expansion of the incoming laser beam. This method uses two diffractive optical elements (DOEs), one converts the input Gaussian intensity profile to an intermediate intensity distribution, which illuminates the second DOE, a binary axicon. BBs of desired axial intensity distribution over few centimeters length can be fabricated.

physics.optics↗

arXiv2017

Interaction of the ultra-short Bessel beam with transparent dielectrics: Evidence of high-energy concentration and multi-TPa pressure

It has been proven that the intense tightly focused Gauss beam (GB) generates pressures in excess of a few TPa creating the novel super-dense phases of Aluminium and silicon [1-5]. Recently it was demonstrated that the Bessel beam (BB) focused inside sapphire produced the cylindrical void being two orders of magnitude larger than that generated by the GB [6-8]. Analysis of the experimental data presented below allows making the remarkable conclusions based solely on the void size measurements without any ad hoc assumptions about the interaction process. First, the void size is direct evidence of strong (>40%) absorption of the pulse energy. Second, it is a direct experimental evidence of the high-energy concentration in the central spike of the focus. The unique features of the intense Bessel beam interaction then allow understanding the experimental observation. This interaction generates early in the pulse time the spatial distribution of excited permittivity changing from positive to negative values. Then the light interacts with zero-real-permittivity surface, separating plasma and dielectric areas, which leads to high energy concentration near the axis of cylindrical focus up to several MJ/cm3 (pressure range of 4-8 TPa). The effect depends on the angle between the permittivity gradient and the field polarisation. High pressure generates intense cylindrical shock/ rarefaction waves, which led to formation of void and compressed shell. We demonstrate that the Bessel beam proves to be an effective tool for producing extreme pressure/temperature conditions on the laboratory tabletop. It appears that adjusting polarisation and permittivity gradient might be a novel way for increasing the maximum pressure. This tool allows for search of novel high-pressure material phases, for the 3D laser machining and for creating Warm Dense Matter as those in star cores.

physics.optics↗

arXiv2017

Nanoscale chemical mapping of laser-solubilized silk

A water soluble amorphous form of silk was made by ultra-short laser pulse irradiation and detected by nanoscale IR mapping. An optical absorption-induced nanoscale surface expansion was probed to yield the spectral response of silk at IR molecular fingerprinting wavelengths with a high ~20 nm spatial resolution defined by the tip of the probe. Silk microtomed sections of 1-5 micrometers in thickness were prepared for nanoscale spectroscopy and a laser was used to induce amorphisation. Comparison of silk absorbance measurements carried out by table-top and synchrotron Fourier transform IR spectroscopy proved that chemical imaging obtained at high spatial resolution and specificity (able to discriminate between amorphous and crystalline silk) is reliably achieved by nanoscale IR. A nanoscale material characterization using synchrotron IR radiation is discussed.

physics.app-ph↗

arXiv2017

3D laser printing by ultra-short laser pulses for micro-optical applications: towards telecom wavelengths

Three dimensional (3D) fast (< 0.5 hour) printing of micro-optical elements down to sub-wavelength resolution over 100 micrometers footprint areas using femtosecond (fs-)laser oscillator is presented. Using sub-1 nJ pulse energies, optical vortex generators made of polymerised grating segments with an azimuthally changing orientation have been fabricated in SZ2080 resist; width of polymerised rods was ~150 nm and period 0.6-1 micrometers. Detailed phase retardance analysis was carried out manually with Berek compensator (under a white light illumination) and using an equivalent principle by an automated Abrio implementation at 546 nm. Direct experimental measurements of retardance was required since the period of the grating was comparable (or larger) than the wavelength of visible light. By gold sputtering, transmission-type optical vortex generators were turned into reflective ones with augmented retardance, n.h defined by the form birefringence, n, and the height h = 2d where d is the thickness of the polymerised structure. Retardance reached 315 nm as measured with Berek compensator at visible wavelengths. Birefringent phase delays of 180 degrees (or half-wavelength) required for high purity vortex generators can be made based on the proposed approach. Optical vortex generators for telecom wavelengths with sub-wavelength patterns of azimuthally oriented gratings are amenable by direct laser polymerisation.

physics.optics↗

arXiv2017

Photoacoustic signal enhancements from gold nano-colloidal suspensions excited by a pair of time-delayed femtosecond pulses

Photoacoustic signal enhancements were observed with a pair of time-delayed femtosecond pulses upon excitation of gold nanosphere colloidal suspension. A systematic experimental investigation of photoacoustic intensity within the delay time, t = 0 to 15 ns, was carried out. The results revealed a significant enhancement factor of ~2 when the pre-pulse energy is 20-30% of the total energy. Pre-pulse and main pulse energy ratios, E(1)p-pol. :E(2)s-pol. were varied to determine the optimal ratio that yields to maximum photoacoustic signal enhancement. This enhancement was ascribed to the initial stage of thermalization and bubble generation in the nanosecond time scale. Pre-pulse scattering intensity measurements and numerical finite-difference time-domain calculations were performed to reveal dynamics and light field enchancement, respectively.

cond-mat.mes-hall↗

arXiv2017

Polarisation of THz synchrotron radiation: from its measurement to control

Polarisation analysis of synchrotron THz radiation was carried out with a standard stretched polyethylene polariser and revealed that the linearly polarised (horizontal) component contributes up to 22 +/- 5% to the circular polarised synchrotron emission extracted by a gold-coated mirror with a horizontal slit inserted near a bending magnet edge. Comparison with theoretical predictions shows a qualitative match with dominance of the edge radiation. Grid polarisers 3D-printed out of commercial acrilic resin were tested for the polariser function and showed spectral regions where the dichroic ratio DR > 1 and < 1 implying importance of molecular and/or stress induced anisotropy. Metal-coated 3D-printed THz optical elements can find a range of applications in intensity and polarisation control of THz beams.

physics.ins-det↗

arXiv2017

Optical readout of hydrogen storage in films of Au and Pd

For hydrogen sensor and storage applications, films of Au and Pd were (i) co-sputtered at different rates or (ii) deposited in a sequential layer-by-layer fashion on a cover glass. Peculiarities of hydrogen uptake and release were optically monitored using 1.3 micrometers wavelength light. Increase of optical transmission was observed for hydrogenated Pd-rich films of 10-30 nm thickness. Up to a three times slower hydrogen release took place as compared with the hydrogen uptake. Composition ratio of Au:Pd and thermal treatment of films provided control over the optical extinction changes and hydrogen uptake/release time constants. Higher uptake and release rates were observed in the annealed Au:Pd films as compared to those deposited at room temperature and were faster for the Au-richer films. Three main parameters relevant for sensors: sensitivity, selectivity, stability (reproducibility) are discussed together with the hydrogenation mechanism in Au:Pd alloys.

cond-mat.mes-hall↗

arXiv2017

Two-color pump-probe interferometry of ultra-fast light-matter interaction

Two-color side-view probing of light-matter interaction from minute focal volume of a tightly focused fs-laser pump pulse reveals charge dynamics with high 0.9 micrometers optical resolution and approximately ~20 fs temporal resolution in coincidence between pump and probe pulses. Use of two colors is advantageous for probing optically excited plasma regions with different density. Holographical digital focusing and spatial filtering were implemented to obtain the same resolution images for subsequent Fourier analysis. Fast electron removal with time constant ~150 fs was resolved and is consistent with self-trapping. Potential applications of an optical control over a light-induced defect placement with deep-sub-wavelength resolution is discussed.

physics.optics↗

arXiv2017

Orientational Mapping Augmented Sub-Wavelength Hyper-Spectral Imaging of Silk

Molecular alignment underpins optical, mechanical, and thermal properties of materials, however, its direct measurement from volumes with micrometer dimensions is not accessible, especially, for structurally complex bio-materials. How the molecular alignment is linked to extraordinary properties of silk and its amorphous-crystalline composition has to be accessed by a direct measurement from a single silk fiber. Here, we show orientation mapping of the internal silk fiber structure via polarisation-dependent IR absorbance at high spatial resolution of 4.2 micrometers and 1.9 micrometers in a hyper-spectral IR imaging by attenuated total reflection using synchrotron radiation in the spectral fingerprint region around 6 micrometers wavelength. Free-standing longitudinal micro-slices of silk fibers, thinner than the fiber cross section, were prepared by microtome for the four polarisation method to directly measure the orientational sensitivity of absorbance in the molecular fingerprint spectral window of the amide bands of b-sheets and amorphous polypeptides of silk. Flat lateral micro-slices of silk eliminates shape related artefact in determination of absorbance anisotropy and order parameters of the amide bands.

physics.bio-ph↗

arXiv2016

Dielectric geometric phase optical elements from femtosecond direct laser writing

We propose to use femtosecond direct laser writing technique to realize dielectric optical elements from photo-resist materials for the generation of structured light from purely geometrical phase transformations. This is illustrated by the fabrication and characterization of spin-to-orbital optical angular momentum couplers generating optical vortices of topological charge from 1 to 20. In addition, the technique is scalable and allows obtaining microscopic to macroscopic flat optics. These results thus demonstrate that direct 3D photopolymerization technology qualifies for the realization of spin-controlled geometric phase optical elements.

physics.optics↗

arXiv2016

Laser printed nano-gratings: orientation and period peculiarities

Understanding of material behaviour at nanoscale under intense laser excitation is becoming critical for future application of nanotechnologies. Nanograting formation by linearly polarised ultra-short laser pulses has been studied systematically in fused silica for various pulse energies at 3D laser printing/writing conditions, typically used for the industrial fabrication of optical elements. The period of the nanogratings revealed a dependence on the orientation of the scanning direction. A tilt of the nanograting wave vector at a fixed laser polarisation was also observed. The mechanism responsible for this peculiar dependency of several features of the nanogratings on the writing direction is qualitatively explained by considering the heat transport flux in the presence of a linearly polarised electric field, rather than by temporal and spatial chirp of the laser beam. The confirmed vectorial nature of the light-matter interaction opens new control of material processing with nanoscale precision.

physics.optics↗

arXiv2016

Engineering and localization of quantum emitters in large hexagonal boron nitride layers

Hexagonal boron nitride (hBN) is a wide bandgap van der Waals material that has recently emerged as promising platform for quantum photonics experiments. In this work we study the formation and localization of narrowband quantum emitters in large flakes (up to tens of microns wide) of hBN. The emitters can be activated in as-grown hBN by electron irradiation or high temperature annealing, and the emitter formation probability can be increased by ion implantation or focused laser irradiation of the as-grown material. Interestingly, we show that the emitters are always localized at edges of the flakes, unlike most luminescent point defects in 3D materials. Our results constitute an important step on the road map of deploying hBN in nanophotonics applications.

cond-mat.mtrl-sci↗

arXiv2016

Efficient X-ray generation from gold colloidal solutions

Hard X-ray generation for Au nanoparticle dispersion was systematically investigated for different particle diameters ranging from 10 to 100 nm with a narrow size distribution of +/- 2%. Scaling law of X-ray generation is close to a 6-photon process before the onset of saturation for excitation by 45 fs laser pulses with central wavelength of 800 nm. This is consistent with bulk plasmon excitation at wavelength ~ 138 nm. The longitudinal E-field component due to nanoparticle focusing is responsible for the excitation of the longitudinal bulk plasmon. The proposed analysis also explains X-ray emission from water breakdown via an electron solvation mechanism at ~6.2 eV. The most efficient emission of X-rays was observed for 40 +/- 10 nm diameter nanoparticles which also had the strongest UV extinction. X-ray emission was the most efficient when induced by pre-chirped 370 +/- 20 fs laser pulses and exhibited the highest intensity at a negative chirp.

cond-mat.mes-hall↗

arXiv2016

Au-Ag-Cu nano-alloys: tailoring of permittivity

Precious metal alloys enables new possibilities to tailor materials for specific optical functions. Here we present a systematic study of the effects of a nanoscale alloying on the permittivity of Au-Ag-Cu metals at 38 different atomic mixing ratios. The permittivity was measured and analyzed numerically by applying the Drude model. X-ray diffraction (XRD) revealed the face centered cubic lattice of the alloys. Both, optical spectra and XRD results point towards an equivalent composition-dependent electron scattering behavior. Correlation between the fundamental structural parameters of alloys and the resulting optical properties is elucidated. Plasmonic properties of the Au-Ag-Cu alloy nanoparticles were investigated by numerical simulations. Guidelines for designing plasmonic response of nano- structures and their patterns are presented from the material science perspective.

cond-mat.mtrl-sci↗

arXiv2016

Solar water splitting: efficiency discussion

The current state of the art in direct water splitting in photo-electrochemical cells (PECs) is presented together with: (i) a case study of water splitting using a simple solar cell with the most efficient water splitting electrodes and (ii) a detailed mechanism analysis. Detailed analysis of the energy balance and efficiency of solar hydrogen production are presented. The role of hydrogen peroxide formation as an intermediate in oxygen evolution reaction is newly revealed and explains why an oxygen evolution is not taking place at the thermodynamically expected 1.23 V potential. Solar hydrogen production with electrical-to-hydrogen conversion efficiency of 52% is demonstrated using a simple ~0.7%-efficient n-Si/Ni Schottky solar cell connected to a water electrolysis cell. This case study shows that separation of the processes of solar harvesting and electrolysis avoids photo-electrode corrosion and utilizes optimal electrodes for hydrogen and oxygen evolution reactions and achieves ~10% efficiency in light-to-hydrogen conversion with a standard 18% efficient household roof Si-solar cells.

physics.chem-ph↗