arXiv subjects

Sean V. Hum

Publications and source records attributed to Sean V. Hum.

15 recordsLinked to original sources

arXiv2023

Design of Rim-Located Reconfigurable Reflectarrays for Interference Mitigation in Reflector Antennas

Radio telescopes are susceptible to interference arriving through its sidelobes. If a reflector antenna could be retrofitted with an adaptive null steering system, it could potentially mitigate this interference. The design of a reflectarray which can be used to reconfigure a radio telescopes radiation pattern by driving a null to the angle of incoming interference is presented. The reflectarray occupies only a portion of the rim of the original reflector and lays conformal to the paraboloid within this region. The conformal reflectarray contains unit cells with 1-bit reconfigurability stemming from two symmetrically placed PIN diodes. It is found that the dielectric and switch losses introduced by the reflectarray do not significantly affect the radio telescopes efficiency since the reflectarray is placed only along the outer rim of the reflector which is weakly illuminated. Simulation results of an L-band reconfigurable reflectarray for an 18m prime focus fed parabola are presented.

eess.SY↗

arXiv2022

Inverse Design of Multi-band Reflective Polarizing Metasurfaces Using Generative Machine Learning

Electromagnetic linear-to-circular polarization converters with wide- and multi-band capabilities can simplify antenna systems where circular polarization is required. Multi-band solutions are attractive in satellite communication systems, which commonly have the additional requirement that the sense of polarization is reversed {between adjacent bands}. However, the design of these structures using conventional \textit{ad hoc} methods relies heavily on empirical methods. Here, we employ a data-driven approach integrated with a generative adversarial network to explore the design space of the polarizer meta-atom thoroughly. Dual-band and triple-band reflective polarizers with stable performance over incident angles up to and including $30^\circ$, {corresponding to typical reflector antenna system requirements}, are synthesized using the proposed method. The feasibility and performance of the designed polarizer is validated through measurements of a fabricated prototype.

physics.optics↗

arXiv2022

Inverse Design and Experimental Verification of a Bianisotropic Metasurface Using Optimization and Machine Learning

Electromagnetic metasurfaces have attracted significant interest recently due to their low profile and advantageous applications. Practically, many metasurface designs start with a set of constraints for the radiated far-field, such as main-beam direction(s) and side lobe levels, and end with a non-uniform physical structure for the surface. This problem is quite challenging, since the required tangential field transformations are not completely known when only constraints are placed on the scattered fields. Hence, the required surface properties cannot be solved for analytically. Moreover, the translation of the desired surface properties to the physical unit cells can be time-consuming and difficult, as it is often a one-to-many mapping in a large solution space. Here, we divide the inverse design process into two steps: a macroscopic and microscopic design step. In the former, we use an iterative optimization process to find the surface properties that radiate a far-field pattern that complies with specified constraints. This iterative process exploits non-radiating currents to ensure a passive and lossless design. In the microscopic step, these optimized surface properties are realized with physical unit cells using machine learning surrogate models. The effectiveness of this end-to-end synthesis process is demonstrated through measurement results of a beam-splitting prototype.

cond-mat.mtrl-sci↗

arXiv2021

Extreme Beam-forming with Impedance Metasurfaces Featuring Embedded Sources and Auxiliary Surface Wave Optimization

We present the end-to-end design of compact passive and lossless metasurface (MTS) antennas with integrated feeds. The complete low-profile system consists of a single-layered reactive impedance MTS printed on top of a grounded dielectric substrate, and is fed by sources which are embedded inside the substrate. An accurate and efficient volume-surface integral equation-based model of the device is developed, and used as the basis for the rapid optimization of its performance. The optimized designs leverage tailored auxiliary surface waves supported by the impedance MTS to distribute the localized source power across their apertures. This facilitates the realization of extreme field transformations such as wide-angle beam-forming or shared-aperture beam-forming, with nearly 100% aperture efficiencies. The procedure also allows for arbitrary beam-shaping with complete main beam and side lobe control. We also derive several feasibility-related constraints, which can significantly enhance the power efficiency as well as the bandwidth of the MTS antennas when they are implemented in practice. Full-wave numerical simulations confirm the effectiveness of the presented approach, as well as the extreme field transformation capabilities of the synthesized designs.

physics.app-ph↗

arXiv2021

Extreme Beam-forming with Metagrating-assisted Planar Antennas

We present a highly efficient metagrating-assisted antenna (MGA) architecture with a simple integrated feed. Power from a localized line source is distributed throughout the arbitrarily large antenna aperture with the help of a passive and lossless electromagnetic metagrating (MG). With appropriately designed meta-wire loading, the omnidirectional source field can be efficiently transformed into directive radiation. To aid the design process, a 2-dimensional volume-surface integral equation framework which accurately predicts the radiation pattern of the MGA is developed. Through constrained optimization, the directivity of the MGA in the desired direction is maximized. In this way, extreme-angle beam steering is demonstrated.

eess.SP↗

arXiv2021

An Efficient Integral Equation Method for Full-wave Analysis of Inhomogeneous Electromagnetic Surfaces with Connected Conductors

In this paper, a generalized macromodeling approach is presented to simulate complex electromagnetic (EM) surfaces consisting of unit cells with connected conductors. Macromodels of each unit cell are produced by applying the equivalence principle on fictitious surfaces encapsulating them. Unit cells often consist of multiple dielectric layers and conductor traces, featuring multiscale structures. Challenges arise when a current-carrying conductor trace traverses the fictitious surface. Hence, a new method based on half Rao-Wilton-Glisson basis functions is proposed to accurately ensure the continuity of the surface currents and avoid singularities at the intersections. The accuracy of the proposed approach is validated by comparing the results with commercial solvers for different EM surfaces.

math.NA↗

arXiv2021

A Combined Machine-Learning / Optimization-Based Approach for Inverse Design of Nonuniform Bianisotropic Metasurfaces

Electromagnetic metasurface design based on far-field constraints without the complete knowledge of the fields on both sides of the metasurface is typically a time consuming and iterative process, which relies heavily on heuristics and ad hoc methods. This paper proposes an end-to-end systematic and efficient approach where the designer inputs high-level far-field constraints such as nulls, sidelobe levels, and main beam level(s); and a 3-layer non-uniform passive, lossless, omega-type bianisotropic electromagnetic metasurface design to satisfy them is returned. The surface parameters to realize the far-field criteria are found using the alternating direction method of multipliers on a homogenized model derived from the method of moments. This model incorporates edge effects of the finite surface and mutual coupling in the inhomogeneous impedance sheet. Optimization through the physical unit cell space integrated with machine learning-based surrogate models is used to realize the desired surface parameters from physical meta-atom (or unit cell) designs. Two passive lossless examples with different feeding systems and far-field constraints are shown to demonstrate the effectiveness of this method.

physics.optics↗

arXiv2020

Optimization of Scalar and Bianisotropic Electromagnetic Metasurface Parameters Satisfying Far-Field Criteria

Electromagnetic metasurfaces offer the capability to realize almost arbitrary power conserving field transformations. These field transformations are governed by the generalized sheet transition conditions, which relate the tangential fields on each side of the surface through the surface parameters. Ideally, engineers would like to determine the surface parameters for transformations based on their application-specific far-field criteria. However, determining the surface parameters to satisfy these criteria is challenging without direct knowledge of the tangential fields on one side of the surface, which are not unique for a given far field pattern. As a result, current design is restricted to analytical examples where the tangential fields are solvable or other ad hoc methods. This paper presents a convex optimization-based scheme which determines surface parameters, such as surface impedance, admittance, and magneto-electric coupling, which satisfy far-field constraints such as beam magnitude, side lobe level, and null locations. The optimization is performed on a model constructed using the method of moments. This model incorporates edge effects and mutual coupling. The resulting non-convexity from this model is relaxed using the alternating direction method of multipliers. Examples of this optimization scheme performing multi-criteria pattern forming, extreme angle small surface refraction, and Chebyshev beamforming are presented.

physics.app-ph↗

arXiv2020

Approach to the Analysis and Synthesis of Cylindrical Metasurfaces with Non-circular Cross Sections Based on Conformal Transformations

We present methods for analyzing and designing cylindrical electromagnetic metasurfaces with non-circular cross sections based on conformal transformations. It can be difficult to treat surfaces with non-canonical geometries since they generally do not admit straightforward solutions to the Helmholtz wave equation subject to the appropriate boundary conditions. This leads to the reliance on full wave numerical techniques which are only suitable for the analysis, but not the synthesis, of these surfaces. We address this issue by employing conformal transformations to map the physical space into a computational space in which the surface coincides with a circular cylinder. The electromagnetic boundary conditions on the surface remain intact under the transformations due to their angle-preserving nature. However, they are much more easily enforced. As a result, analytical modal solutions for the scattered fields are readily obtainable, which facilitate closed-form analysis and synthesis equations for general non-circular cylindrical metasurfaces. One important utility enabled by the proposed framework is the efficient identification of electromagnetic field distributions that satisfy local power conservation. This leads to passive and lossless surface designs, which are highly desirable in practice as they do not require active and/or lossy components.

physics.optics↗

arXiv2020

A Generative Machine Learning-Based Approach for Inverse Design of Multilayer Metasurfaces

The synthesis of a metasurface exhibiting a specific set of desired scattering properties is a time-consuming and resource-demanding process, which conventionally relies on many cycles of full-wave simulations. It requires an experienced designer to choose the number of the metallic layers, the scatterer shapes and dimensions, and the type and the thickness of the separating substrates. Here, we propose a generative machine learning (ML)-based approach to solve this one-to-many mapping and automate the inverse design of dual- and triple-layer metasurfaces. Using this approach, it is possible to solve multiobjective optimization problems by synthesizing thin structures composed of potentially brand-new scatterer designs, in cases where the inter-layer coupling between the layers is non-negligible and synthesis by traditional methods becomes cumbersome. Various examples to provide specific magnitude and phase responses of $x$- and $y$-polarized scattering coefficients across a frequency range as well as mask-based responses for different metasurface applications are presented to verify the practicality of the proposed method.

eess.SP↗

arXiv2020

A Discrete Fourier Transform-Based Framework for Analysis and Synthesis of Cylindrical Omega-bianisotropic Metasurfaces

This paper presents a framework for analyzing and designing cylindrical omega-bianisotropic metasurfaces, inspired by mode matching and digital signal processing techniques. Using the discrete Fourier transform, we decompose the the electromagnetic field distributions into orthogonal cylindrical modes and convert the azimuthally varying metasurface constituent parameters into their respective spectra. Then, by invoking appropriate boundary conditions, we set up systems of algebraic equations which can be rearranged to either predict the scattered fields of prespecified metasurfaces, or to synthesize metasurfaces which support arbitrarily stipulated field transformations. The proposed framework facilitates the efficient evaluation of field distributions that satisfy local power conservation, which is one of the key difficulties involved with the design of passive and lossless scalar metasurfaces. It represents a promising solution to circumvent the need for active components, controlled power dissipation, or tensorial surface polarizabilities in many state-of-the art conformal metasurface-based devices. To demonstrate the robustness and the versatility of the proposed technique, we design several devices intended for different applications and numerically verify them using finite element simulations.

physics.class-ph↗

arXiv2019

A Fast Macromodeling Approach to Efficiently Simulate Inhomogeneous Electromagnetic Surfaces

The full-wave simulation of complex electromagnetic surfaces such as reflectarrays and metasurfaces is a challenging problem. In this paper, we present a macromodeling approach to efficiently simulate complex electromagnetic surfaces composed of PEC traces, possibly with fine features, on a finite-sized multilayer dielectric substrate. In our approach, we enclose each element of the structure with a fictitious surface. By applying the equivalence principle on each surface, we derive a macromodel for each element of the array. This macromodel consists of a linear operator that relates the equivalent electric and magnetic current densities introduced on the fictitious surface. Mutual coupling between the elements of the structure is captured by the equivalent current densities in a fully accurate way. The crux of the proposed technique is to solve for equivalent current densities on the fictitious surface instead of directly solving for the actual current densities on the original scatterer. When simulating complex surfaces, this approach leads to fewer unknowns and better conditioning. We also propose a rigorous acceleration algorithm based on the fast Fourier transform to simulate electrically large surfaces. Numerical results demonstrate that the proposed approach is significantly faster and requires less memory than commercial solvers based on the surface integral equation method, while giving accurate results.

cs.CE↗

arXiv2018

A Complete Surface Integral Method for Broadband Modeling of 3D Interconnects in Stratified Media

A surface integral equation solver is proposed for fast and accurate simulation of interconnects embedded in stratified media. A novel technique for efficient computation of the multilayer Green's function is proposed. Using the Taylor expansion of Bessel functions, the computation of Sommerfeld integrals during the method of moments procedure is reduced to simple algebraic operations. To model skin effect in conductors, the single-source differential surface admittance operator is extended to conductors in stratified media. To handle large realistic structures, the adaptive integral method is developed for a multilayer environment in a generalized manner that poses no restrictions on layout of conductors, and requires no special grid refinement, unlike previous works. The proposed method is made robust over a wide frequency range with the augmented electric field integral equation. Realistic structures of different shapes and electrical sizes are successfully analyzed over a wide frequency range, and results are validated against a commercial finite element tool.

physics.comp-ph↗

arXiv2017

A Macromodeling Approach to Efficiently Compute Scattering from Large Arrays of Complex Scatterers

Full-wave electromagnetic simulations of electrically large arrays of complex antennas and scatterers are challenging, as they consume large amount of memory and require long CPU times. This paper presents a new reduced-order modeling technique to compute scattering and radiation from large arrays of complex scatterers and antennas. In the proposed technique, each element of the array is replaced by an equivalent electric current distribution on a fictitious closed surface enclosing the element. This equivalent electric current density is derived using the equivalence theorem and it is related to the surface currents on the scatterer by the Stratton-Chu formulation. With the proposed approach, instead of directly solving for the unknown surface current density on the scatterers, we only need to solve for the unknowns on the equivalent surface. This approach leads to a reduction in the number of unknowns and better conditioning when it is applied to problems involving complex scatterers with multiscale features. Furthermore, the proposed approach is accelerated with the adaptive integral equation method to solve large problems. As illustrated in several practical examples, the proposed method yields speed up of up to 20 times and consumes up to 12 times less memory than the standard method of moments accelerated with the adaptive integral method.

cs.CE↗

arXiv2016

A Novel Single-Source Surface Integral Method to Compute Scattering from Dielectric Objects

Using the traditional surface integral methods, the computation of scattering from a dielectric object requires two equivalent current densities on the boundary of the dielectric. In this paper, we present an approach that requires only a single current density. Our method is based on a surface admittance operator and is applicable to dielectric bodies of arbitrary shape. The formulation results in four times lower memory consumption and up to eight times lower time to solve the linear system than the traditional PMCHWT formulation. Numerical results demonstrate that the proposed technique is as accurate as the PMCHWT formulation.

cs.CE↗