arXiv subjects

Seth R. Marder

Publications and source records attributed to Seth R. Marder.

12 recordsLinked to original sources

arXiv2025

Trion Formation Hampers Single Quantum Dot Performance in Silane-Coated FAPbBr3 Quantum Dots

We explore silane-coated formamidinium lead bromide (FAPbBr3) quantum dots as single photon emitters and compare them to FAPbBr3 quantum dots passivated with a phosphoethylammonium derivative (PEAC8C12), which represents current state-of-the-art in zwitterionic molecular surface ligand passivation. We compare properties including single-photon purity (g2(t)), linewidth, blinking, and photostability. We find that at room temperature, these silane-coated dots perform comparably to the PEAC8C12 passivation in terms of single-photon performance metrics, while exhibiting improvements in photostability. However, we find that at 4K, silane-coated FAPbBr3 quantum dots perform worse than the PEAC8C12-passivated samples, exhibiting faster blue-shifting and photobleaching under illumination. Analysis of fluorescence lifetime intensity distributions from the photon-counting data indicates increased efficiency of fast non-radiative processes in the silane-coated quantum dots at 4K. We propose a trion related degradation pathway at low temperatures that is consistent with the observed kinetics and estimate that at 4K with 6.1 uJ/cm2, 472 nm excitation the silane-coated quantum dots build up double the trion population of their PEAC8C12-passivated counterparts.

cond-mat.mtrl-sci↗

arXiv2025

Surface Passivation for Halide Optoelectronics: Comparing Optimization and Reactivity of Amino-Silanes with Formamidinium

Amino-silane-based surface passivation schemes are gaining attention in halide perovskite optoelectronics, with varying levels of success. We compare surface treatments using (3-aminopropyl)trimethoxysilane (APTMS) and [3-(2-aminoethylamino)propyl]trimethoxysilane (AEAPTMS), applied via room-temperature vacuum deposition, to the perovskite FA0.78Cs0.22Pb(I0.85Br0.15)3 (FA = formamidinium). Both molecules improve thin-film photoluminescence properties and photovoltaic device performance, although their effectiveness depends strongly on deposition time. We show AEAPTMS has a wider, more robust processing window and yields higher performance under optimized conditions. In contrast, over-exposure, particularly with APTMS, reduces performance, with notable reductions in photoluminescence lifetime and absorbance. To probe the underlying chemistry, we employ nuclear magnetic resonance (NMR) spectroscopy and depth-resolved time-of-flight secondary ion mass spectrometry (ToF-SIMS), demonstrating that both amino-silanes react with formamidinium (FA+) cations in solution and in the solid state. This work underscores the importance of optimizing deposition conditions to balance effective passivation with potential performance loss and elucidates previously unrecognized reactive chemistry between amino-silane passivating agents and halide perovskites.

cond-mat.mtrl-sci↗

arXiv2025

Deposition-Dependent Coverage and Performance of Phosphonic Acid Interface Modifiers in Halide Perovskite Optoelectronics

In this work, we study the effect of various deposition methods for phosphonic acid interface modifiers commonly pursued as self-assembled monolayers in high-performance metal halide perovskite photovoltaics and light-emitting diodes. We compare the deposition of (2-(3,6-diiodo-9H-carbazol-9-yl)ethyl)phosphonic acid onto indium tin oxide (ITO) bottom contacts by varying three parameters: the method of deposition, specifically spin coating or prolonged dip coating, ITO surface treatment via HCl/FeCl3 etching, and use in combination with a second modifier, 1,6-hexylenediphosphonic acid. We demonstrate that varying these modification protocols can impact time-resolved photoluminescence carrier lifetimes and quasi-Fermi level splitting of perovskite films deposited onto the phosphonic-acid-modified ITO. Ultraviolet photoelectron spectroscopy shows an increase in effective work function after phosphonic acid modification and clear evidence for photoemission from carbazole functional groups at the ITO surface. We use X-ray photoelectron spectroscopy to probe differences in phosphonic acid coverage on the metal oxide contact and show that perovskite samples grown on ITO with the highest phosphonic acid coverage exhibit the longest carrier lifetimes. Finally, we establish that device performance follows these same trends. These results indicate that the reactivity, heterogeneity, and composition of the bottom contact help to control recombination rates and therefore power conversion efficiencies. ITO etching, prolonged deposition times for phosphonic acids via dip coating, and the use of a secondary, more hydrophilic bis-phosphonic acid, all contribute to improvements in surface coverage, carrier lifetime, and device efficiency. These improvements each have a positive impact, and we achieve the best results when all three strategies are implemented.

physics.app-ph↗

arXiv2024

Diamine Surface Passivation and Post-Annealing Enhance Performance of Silicon-Perovskite Tandem Solar Cells

We show that the use of 1,3-diaminopropane (DAP) as a chemical modifier at the perovskite/electron-transport layer (ETL) interface enhances the power conversion efficiency (PCE) of 1.7 eV bandgap FACs mixed-halide perovskite single-junction cells, primarily by boosting the open-circuit voltage (VOC) from 1.06 V to 1.15 V. Adding a post-processing annealing step after C60 evaporation, further improves the fill factor (FF) by 20% from the control to the DAP + post-annealing devices. Using hyperspectral photoluminescence microscopy, we demonstrate that annealing helps improve compositional homogeneity at the top and bottom interfaces of the solar cell, which prevents detrimental bandgap pinning in the devices and improves C60 adhesion. Using time-of-flight secondary ion mass spectrometry, we show that DAP reacts with formamidinium present near the surface of the perovskite lattice to form a larger molecular cation, 1,4,5,6-tetrahydropyrimidinium (THP) that remains at the interface. Combining the use of DAP and the annealing of C60 interface, we fabricate Si-perovskite tandems with PCE of 25.29%, compared to 23.26% for control devices. Our study underscores the critical role of chemical reactivity and thermal post-processing of the C60/Lewis-base passivator interface in minimizing device losses and advancing solar-cell performance of wide-bandgap mixed-cation mixed-halide perovskite for tandem application.

cond-mat.mtrl-sci↗

arXiv2024

Increased Brightness and Reduced Efficiency Droop in Perovskite Quantum Dot Light-Emitting Diodes using Carbazole-Based Phosphonic Acid Interface Modifiers

We demonstrate the use of [2-($\textit{9H}$-carbazol-9-yl)ethyl]phosphonic acid (2PACz) and [2-(3,6-di-$\textit{tert}$-butyl-$\textit{9H}$-carbazol-9-yl)ethyl]phosphonic acid (t-Bu-2PACz) as anode modification layers in metal-halide perovskite quantum dot light-emitting diodes (QLEDs). Compared to conventional QLED structures with PEDOT:PSS (poly(3,4-ethylenedioxythiophene) polystyrene sulfonate)/PVK (poly(9-vinylcarbazole)) hole-transport layers, QLEDs made with phosphonic acid (PA)-modified indium tin oxide (ITO) anodes show an over 7-fold increase in brightness, achieving a brightness of 373,000 cd m$^{-2}$, one of the highest brightnesses reported to date for colloidal perovskite QLEDs. Importantly, the onset of efficiency roll-off, or efficiency droop, occurs at ~1000-fold higher current density for QLEDs made with PA-modified anodes compared to control QLEDs made with conventional PEDOT:PSS/PVK hole transport layers, allowing the devices to sustain significantly higher levels of external quantum efficiency at a brightness of >10$^{5}$ cd m$^{-2}$. Steady-state and time-resolved photoluminescence measurements indicate these improvements are due to a combination of multiple factors, including reducing quenching of photoluminescence at the PEDOT:PSS interface and reducing photoluminescence efficiency loss at high levels of current density.

cond-mat.mtrl-sci↗

arXiv2024

Surface doping of rubrene single crystals by molecular electron donors and acceptors

The surface molecular doping of organic semiconductors can play an important role in the development of organic electronic or optoelectronic devices. Single-crystal rubrene remains a leading molecular candidate for applications in electronics due to its high hole mobility. In parallel, intensive research into the fabrication of flexible organic electronics requires the careful design of functional interfaces to enable optimal device characteristics. To this end, the present work seeks to understand the effect of surface molecular doping on the electronic band structure of rubrene single crystals. Our angle-resolved photoemission measurements reveal that the Fermi level moves in the band gap of rubrene depending on the direction of surface electron-transfer reactions with the molecular dopants, yet the valence band dispersion remains essentially unperturbed. This indicates that surface electron-transfer doping of a molecular single crystal can effectively modify the near-surface charge density, while retaining good charge-carrier mobility.

cond-mat.mtrl-sci↗

arXiv2023

Architecture Optimization Dramatically Improves Reverse Bias Stability in Perovskite Solar Cells: A Role of Polymer Hole Transport Layers

We report that device architecture engineering has a substantial impact on the reverse bias instability that has been reported as a critical issue in commercializing perovskite solar cells. We demonstrate breakdown voltages exceeding -15 V in typical pin structured perovskite solar cells via two steps: i) using polymer hole transporting materials; ii) using a more electrochemically stable gold electrode. While device degradation can be exacerbated by higher reverse bias and prolonged exposure, our as-fabricated perovskite solar cells completely recover their performance even after stressing at -7 V for 9 hours both in the dark and under partial illumination. Following these observations, we systematically discuss and compare the reverse bias driven degradation pathways in perovskite solar cells with different device architectures. Our model highlights the role of electrochemical reaction rates and species in dictating the reverse bias stability of perovskite solar cells.

physics.chem-ph↗

arXiv2023

Tailoring on-surface molecular reactions and assembly through hydrogen-modified synthesis: From triarylamine monomer to 2D covalent organic framework

Relative to conventional wet-chemical synthesis techniques, on-surface synthesis of organic networks in ultrahigh vacuum has few control parameters. The molecular deposition rate and substrate temperature are typically the only synthesis variables to be adjusted dynamically. Here we demonstrate that reducing conditions in the vacuum environment can be created and controlled without dedicated sources -- relying only on backfilled hydrogen gas and ion gauge filaments -- and can dramatically influence the Ullmann-like on-surface reaction used for synthesizing two-dimensional covalent organic frameworks (2D COFs). Using tribromo dimethylmethylene-bridged triphenylamine ((Br$_3$)DTPA) as monomer precursors, we find that atomic hydrogen blocks aryl-aryl bond formation. Control of the relative monomer and hydrogen fluxes is used to produce large islands of self-assembled monomers, dimers, or macrocycle hexamers. On-surface synthesis of these oligomers, from a single precursor, circumvents potential challenges with protracted wet-chemical synthesis or low precursor volatility for large molecules. Using scanning tunneling microscopy and spectroscopy (STM/STS), we show that changes in the electronic states through this oligomer sequence provide an insightful view of the 2D-COF (synthesized in the absence of atomic hydrogen) as the endpoint in an evolution of electronic structures from the monomer.

cond-mat.mtrl-sci↗

arXiv2022

Ethylenediamine Addition Improves Performance and Suppresses Phase Instabilities in Mixed-Halide Perovskites

We show that adding ethylenediamine (EDA) to perovskite precursor solution improves the photovoltaic device performance and material stability of high-bromide-content, methylammonium-free, formamidinium cesium lead halide perovskites FA1-xCsxPb(I1-yBry)3 which are currently of interest for perovskite-on-Si tandem solar cells. Using spectroscopy and hyperspectral microscopy, we show that the additive improves film homogeneity and suppresses the phase instability that is ubiquitous in high-Br perovskite formulations, producing films that remain stable for over 100 days in ambient conditions. With the addition of 1 mol% EDA we demonstrate 1.69 eV-gap perovskite single-junction p-i-n devices with a VOC of 1.22 V, and a champion maximum power point tracked power conversion efficiency of 18.8%, comparable to the best reported methylammonium-free perovskites. Using nuclear magnetic resonance (NMR) spectroscopy and X-ray diffraction techniques, we show that EDA reacts with FA+ in solution, rapidly and quantitatively forming imidazolinium cations. It is the presence of imidazolinium during crystallization which drives the improved perovskite thin-film properties.

cond-mat.mtrl-sci↗

arXiv2021

Cross-Linking of Doped Organic Semiconductor Interlayers for Organic Solar Cells: Potential and Challenges

Solution-processable interlayers are an important building block for the commercialization of organic electronic devices such as organic solar cells. Here, the potential of cross-linking to provide an insoluble, stable and versatile charge transport layer based on soluble organic semiconductors is studied. For this purpose, a photo-reactive tris-azide cross-linker is synthesized. The capability of the small molecular cross-linker is illustrated by applying it to a p-doped polymer used as a hole transport layer in organic solar cells. High cross-linking efficiency and excellent charge extraction properties of the cross-linked doped hole transport layer are demonstrated. However, at high doping levels in the interlayer, the solar cell efficiency is found to deteriorate. Based on charge extraction measurements and numerical device simulations, it is shown that this is due to diffusion of dopants into the active layer of the solar cell. Thus, in the development of future cross-linker materials, care must be taken to ensure that they immobilize not only the host, but also the dopants.

physics.app-ph↗

arXiv2021

High thermoelectric power factor of poly(3-hexylthiophene) through in-plane alignment and doping with a molybdenum dithiolene complex

Here we report a record thermoelectric power factor of up to 160 $μ$ W m-1 K-2 for the conjugated polymer poly(3-hexylthiophene) (P3HT). This result is achieved through the combination of high-temperature rubbing of thin films together with the use of a large molybdenum dithiolene p-dopant with a high electron affinity. Comparison of the UV-vis-NIR spectra of the chemically doped samples to electrochemically oxidized material reveals an oxidation level of 10%, i.e. one polaron for every 10 repeat units. The high power factor arises due to an increase in the charge-carrier mobility and hence electrical conductivity along the rubbing direction. We conclude that P3HT, with its facile synthesis and outstanding processability, should not be ruled out as a potential thermoelectric material.

physics.app-ph↗

arXiv2017

Tunable third-harmonic generation from polaritons in the ultrastrong coupling regime

Strong inter-particle interactions between polaritons have traditionally stemmed from their exciton component. In this work, we impart a strong photonic nonlinearity to a polaritonic mode by embedding a nonlinear polymethine dye within a high-Q all-metal microcavity. We demonstrate nonlinear microcavities operating in the ultrastrong coupling regime with a normalized coupling ratio of 62\%, the highest reported to date. When pumping the lower polariton branch, we observe tunable third-harmonic generation spanning the entire visible spectrum, with internal conversion enhancements more than three orders of magnitude larger than in bare films. Transfer matrix calculations indicate that the observed enhancements are consistent with the enhanced pump electric field.

cond-mat.other↗