arXiv subjects

Simone Calzaferri

Publications and source records attributed to Simone Calzaferri.

9 recordsLinked to original sources

arXiv2026

Application of LHC Gas Recuperation Systems for Methane Emission Control in Livestock Housing

The CH4rLiE (CH4 Livestock Emission) project investigates the technical feasibility of adapting gas recovery systems from high-energy physics to mitigate methane (CH4) emissions in livestock housing. This work presents a proof-of-principle based on the adaptation of CERN's gas recuperation systems for the capture of CH4 at low concentrations. A laboratory-scale prototype was developed to evaluate the performance of various adsorbent materials under realistic conditions, including multi-stage humidity removal and pressurized gas flows. Experimental results obtained with the prototype led to the selection of commercial Z5 zeolite as the primary adsorbent due to its high adsorption capacity and stable regeneration performance through Vacuum Swing Adsorption cycles. The study demonstrates the feasibility of CH4 capture at concentrations down to 0.1%. Furthermore, it was observed that increasing the CH4 partial pressure enhances the adsorption capacity, with tests conducted up to approximately 5 bar. To bridge the gap between laboratory conditions and the representative 10-100 ppm levels found in dairy barn environments, a negative exponential extrapolation was applied to the experimental data. This allowed for the modeling of the adsorption behavior in the ultra-low concentration regime. These results validate the operational principle and provide the necessary parameters for the design of a full-scale system for field installation.

physics.ins-det↗

arXiv2025

MuCol Milestone Report No. 7: Consolidated Parameters

This document is comprised of a collection of consolidated parameters for the key parts of the muon collider. These consolidated parameters follow on from the October 2024 Preliminary Parameters Report. Attention has been given to a high-level consistent set of baseline parameters throughout all systems of the complex, following a 10 TeV center-of-mass design. Additional details of the designs contributing to this baseline design are featured in the appendix. Likewise, explorative variations from this baseline set can be found in the appendix. The data is collected from a collaborative spreadsheet and transferred to overleaf.

physics.acc-ph↗

arXiv2025

First complete characterization of an X-Ray tube through combined measurements and Geant4 simulations

X-ray tubes are sources of X-rays used in various fields, ranging from radiographic imaging in medical physics to the characterization of detectors in particle physics. This article presents a method for the complete characterization of the Mini-X2 X-Ray tube from AMETEK, an X-ray source later used to characterize gas detectors in laboratory. Using data provided by the manual, we derive key operational parameters of the tube, such as the photon emission rate and the relationship between emissive power and supplied current. Based on this characterization, we determine the air dose rate as well as the absorbed dose rate within a given volume at various distances from the source. We derive this dose experimentally, theoretically and through simulations and find good agreement between these. To enable safe operation in a laboratory environment and to support experimental comparisons, a shielding system was developed. Finally, it will be illustrated how the shielding containing the Mini-X2 has been designed, exploiting the simulation power of the Geant4 software.

physics.ins-det↗

arXiv2025

The Muon Collider

Muons offer a unique opportunity to build a compact high-energy electroweak collider at the 10 TeV scale. A Muon Collider enables direct access to the underlying simplicity of the Standard Model and unparalleled reach beyond it. It will be a paradigm-shifting tool for particle physics representing the first collider to combine the high-energy reach of a proton collider and the high precision of an electron-positron collider, yielding a physics potential significantly greater than the sum of its individual parts. A high-energy muon collider is the natural next step in the exploration of fundamental physics after the HL-LHC and a natural complement to a future low-energy Higgs factory. Such a facility would significantly broaden the scope of particle colliders, engaging the many frontiers of the high energy community. The last European Strategy for Particle Physics Update and later the Particle Physics Project Prioritisation Panel in the US requested a study of the muon collider, which is being carried on by the International Muon Collider Collaboration. In this comprehensive document we present the physics case, the state of the work on accelerator design and technology, and propose an R\&D project that can make the muon collider a reality.

physics.acc-ph↗

arXiv2025

Capturing methane in a barn environment: the CH4 Livestock Emission (CH4rLiE) project

The CH4 Livestock Emission (CH4rLiE) project explores the development of a prototype system for capturing methane emissions in barn environments, offering an alternative approach to mitigating greenhouse gas emissions from livestock farming. Methane (CH4), with a global warming potential significantly higher than CO2 (GWP100 = 27), accounts for ~23% of anthropogenic climate impact. In 2021, The Assessment Report 6 of Intergovernmental Panel on Climate Change quantified CH4 livestock emissions in 123 Mt/yr, which, together with substantial N2O and CO2 emissions, contributed with a 12% to global emissions. Unlike strategies focused on altering animal feed, CH4rLiE investigates post-emission capture using porous materials, such as zeolites, to adsorb methane from barn air. The project draws on CERN's experience with gas recovery systems for particle detectors, adapting similar technologies to agricultural settings. Preliminary estimates, based on measured CH4 concentrations (~20 mg/m3) and partial air filtration in a 250-animal barn, suggest a low but detectable recovery potential, subject to validation through simulation and in-situ testing. Prototype development considers the potential for energy-efficient operation - possibly through pressure swing regeneration - and compatibility with existing ventilation infrastructure, though these aspects remain under evaluation. If methane concentrations in barns prove too diluted, the system may be better suited for environments with higher gas levels, such as pigsties or landfills. NH3 capture for fertilizer production is planned as a future enhancement. CH4rLiE aims to assess the feasibility of emission recovery in livestock settings without affecting animal welfare, contributing to sustainable farming practices, resource efficiency, and circular bioeconomy goals.

physics.ins-det↗

arXiv2024

MuCol Milestone Report No. 5: Preliminary Parameters

This document is comprised of a collection of updated preliminary parameters for the key parts of the muon collider. The updated preliminary parameters follow on from the October 2023 Tentative Parameters Report. Particular attention has been given to regions of the facility that are believed to hold greater technical uncertainty in their design and that have a strong impact on the cost and power consumption of the facility. The data is collected from a collaborative spreadsheet and transferred to overleaf.

physics.acc-ph↗

arXiv2023

Towards a Muon Collider

A muon collider would enable the big jump ahead in energy reach that is needed for a fruitful exploration of fundamental interactions. The challenges of producing muon collisions at high luminosity and 10 TeV centre of mass energy are being investigated by the recently-formed International Muon Collider Collaboration. This Review summarises the status and the recent advances on muon colliders design, physics and detector studies. The aim is to provide a global perspective of the field and to outline directions for future work.

physics.acc-ph↗

arXiv2022

Simulated Detector Performance at the Muon Collider

In this paper we report on the current status of studies on the expected performance for a detector designed to operate in a muon collider environment. Beam-induced backgrounds (BIB) represent the main challenge in the design of the detector and the event reconstruction algorithms. The current detector design aims to show that satisfactory performance can be achieved, while further optimizations are expected to significantly improve the overall performance. We present the characterization of the expected beam-induced background, describe the detector design and software used for detailed event simulations taking into account BIB effects. The expected performance of charged-particle reconstruction, jets, electrons, photons and muons is discussed, including an initial study on heavy-flavor jet tagging. A simple method to measure the delivered luminosity is also described. Overall, the proposed design and reconstruction algorithms can successfully reconstruct the high transverse-momentum objects needed to carry out a broad physics program.

hep-ex↗

arXiv2022

Promising Technologies and R&D Directions for the Future Muon Collider Detectors

Among the post-LHC generation of particle accelerators, the muon collider represents a unique machine with capability to provide very high energy leptonic collisions and to open the path to a vast and mostly unexplored physics programme. However, on the experimental side, such great physics potential is accompanied by unprecedented technological challenges, due to the fact that muons are unstable particles. Their decay products interact with the machine elements and produce an intense flux of background particles that eventually reach the detector and may degrade its performance. In this paper, we present technologies that have a potential to match the challenging specifications of a muon collider detector and outline a path forward for the future R&D efforts.

physics.ins-det↗