arXiv subjects

Sinwoo Cho

Publications and source records attributed to Sinwoo Cho.

At least 19 recordsLinked to original sources

arXiv2026

Nonlinear Characterization of Thin-Film LiNbO3 Acoustic Filters

Compact, high-performance components in millimeter-wave (mmWave) communication systems demand new acoustic filter technology at increasingly higher frequencies. Among various promising mmWave platforms, first-order antisymmetric (A1) mode laterally excited bulk acoustic resonators (XBARs) in thin-film lithium niobate (LiNbO3) have perhaps the most impressive linear performance. Despite these advances, there are few reports of nonlinear characterization of LiNbO3 filters at mmWaves. Here, we address this gap by developing a new nonlinear methodology for high-frequency filters. The result is a methodology for performing power-dependent S-parameters and third-order intermodulation (IMD3) measurements. To test our methodology, we fabricated filters on transferred single-crystal LiNbO3 films on sapphire (Al2O3) and silicon (Si) substrates with amorphous silicon (aSi) sacrificial layer. At 21.8 GHz, the filters on Al2O3 demonstrated an insertion loss of 1.48 dB, a 3 dB fractional bandwidth (FBW) of 17.7%, and in-band third-order input intercept points (IIP3) of 50.8 dBm. At 21.6 GHz, the filters on silicon demonstrated an insertion loss of 2.47 dB, a 3 dB FBW of 18.6%, and in-band IIP3 of 46.5 dBm. The nonlinear results conclusively show that thermal stability and passband distortion improved on the Al2O3 substrate, confirming that substrate selection plays a pivotal role in mitigating nonlinearity in acoustic front-end modules.

eess.SP↗

arXiv2025

Residual Stress Anisotropy In Thin-Film Lithium Niobate For Stress-Managed MEMS

In this work, we present the first experimental study of residual stress and post-release beam deflection in 128-degree Y-cut thin-film lithium niobate (TFLN) on Si, revealing pronounced stress anisotropy with in-plane orientation. Using optical profilometry with curvature fitting, we extract the stress gradient (sigma1) and generate orientation-resolved stress maps across multiple film thicknesses (100 nm, 220 nm, and 460 nm). For films in the 220 to 460 nm range, we identify stress-free in-plane orientations near approximately 55 degrees and 125 degrees, enabling extremely flat suspended beams. In contrast, ultra-thin 100 nm films exhibit shifted stress-free orientations near approximately 20 degrees and 160 degrees. Leveraging these orientations, we demonstrate very long suspended beams up to 2 cm in length, 10 micrometers in width, and 460 nm in thickness without collapse. These results establish in-plane stress anisotropy and thickness selection in TFLN as practical design levers for mechanically stable, scalable, and stress-managed microelectromechanical systems (MEMS).

physics.app-ph↗

arXiv2025

An 11.7-GHz ScAlN FBAR Filter: Case Study on Scaling Limits and Challenges

This paper reports an 11.7 GHz compact 50 ohm ladder filter based on single layer Scandium Aluminum Nitride (ScAlN) film bulk acoustic resonators (FBARs) with platinum (Pt) electrodes, and uses it as a quantitative case study of the limits encountered when directly scaling to higher frequencies. The measured filter achieves a 3 dB fractional bandwidth (FBW) of 4.0% and an out of band rejection greater than 23.1 dB, with a minimum insertion loss (IL) of 6.8 dB. We analyze the origin of this performance through a quantitative framework: (1) a loss decomposition study, (2) frequency shift sensitivity that explains the discrepancy between simulated and measured center frequency, (3) FBW sensitivity to series shunt separation and port impedance, and (4) stress limited aperture that constrains device size. The results establish a realistic, fabricable baseline for directly scaled single layer ScAlN FBAR filters and outline materials, electrode, and stress management directions toward lower loss mmWave acoustic filters.

physics.app-ph↗

arXiv2025

50 GHz Piezoelectric Acoustic Filter

This paper presents significant frequency scaling of acoustic filter technology to 50 GHz. This achievement is enabled by the P3F LiNbO3 multilayer stack, in which piezoelectric thin-films of alternating orientations are transferred in sequence, thereby allowing efficient exploitation of high-order modes with high quality factor (Q) and coupling coefficient (k2) in a thicker piezoelectric stack. The demonstrated filter is comprised of twelfth-order symmetric (S12) mode lateral-field-excited bulk acoustic wave resonators (XBARs), built on a 4-layer periodically poled piezoelectric (P3F) 128 Y-cut lithium niobate (LiNbO3) stack. The filter exhibits 3.3 dB insertion loss (IL) and a fractional bandwidth (FBW) of 2.9%. The miniature design, with a footprint of 0.36 mm2, makes it promising for future wireless front-end applications. These results represent the highest frequency acoustic filters reported to date, setting a new benchmark in piezoelectric filter technology. Upon further development, the platform could enable filters further into the FR2 range, essential for next-generation communication systems.

eess.SP↗

arXiv2025

19.3 GHz Acoustic Filter with High Close-in Rejection in Tri-layer Thin-Film Lithium Niobate

Acoustic filters are preferred front-end solutions at sub-6 GHz due to their superior frequency selectivity compared to electromagnetic (EM) counterparts. With the ongoing development of 5G and the evolution toward 6G, there is a growing need to extend acoustic filter technologies into frequency range 3 (FR3), which spans 7 to 24 GHz to accommodate emerging high-frequency bands. However, scaling acoustic filters beyond 10 GHz presents significant challenges, as conventional platforms suffer from increased insertion loss (IL) and degraded out-of-band (OoB) rejection at higher frequencies. Recent innovations have led to the emergence of periodically poled piezoelectric lithium niobate (P3F LN) laterally excited bulk acoustic resonators (XBARs), offering low-loss and high electromechanical coupling performance above 10 GHz. This work presents the first tri-layer P3F LN filter operating at 19.3 GHz, achieving a low IL of 2.2 dB, a 3-dB fractional bandwidth (FBW) of 8.5%, and an impressive 49 dB close in rejection. These results demonstrate strong potential for integration into FR3 diplexers.

eess.SP↗

arXiv2025

Thin-film scandium aluminum nitride bulk acoustic resonator with high Q of 208 and K2 of 9.5% at 12.5 GHz

This work describes sputtered scandium aluminum nitride (ScAlN) thin-film bulk acoustic resonators (FBAR) at 12.5 GHz with high electromechanical coupling (k2) of 9.5% and quality factor (Q) of 208, resulting in a figure of merit (FoM, Qk2) of 19.8. ScAlN resonators employ a stack of 90 nm thick 20% Sc doping ScAlN piezoelectric film on the floating bottom 38 nm thick platinum (Pt) electrode to achieve low losses and high coupling toward centimeter wave (cmWave) frequency band operation. Three fabricated and FBARs are reported, show promising prospects of ScAlN-Pt stack towards cmWave front-end filters.

physics.app-ph↗

arXiv2025

Acoustic resonators above 100 GHz

Piezoelectric resonators are a common building block for signal processing because of their miniature size, low insertion loss, and high quality factor. As consumer electronics push to millimeter waves frequencies, designers must increase the operating frequency of the resonator. The current state-of-the-art approach to increase the operating frequency is to decrease the thickness of the piezoelectric film to shorten the acoustic wavelength or to use higher order modes. Unfortunately, maintaining high crystal quality typically requires thicker piezoelectric layers. Thinner layers suffer from higher defect densities and increased surface damping, which degrade the electromechanical coupling and quality factor. While acoustic high order modes can also increase operating frequency, the electromechanical coupling rapidly decreases with increasing mode number. Here, we overcome these limitations by utilizing a piezoelectric stack of three layers of lithium niobate with alternating crystallographic orientations to preferentially support higher order modes and thereby enhance the electromechanical coupling without degrading the quality factor. Our approach improves the figure of merit of millimeter-wave acoustic resonators by roughly an order of magnitude greater compared to state-of-the-art piezoelectric resonators above 60 GHz. This concept of alternating crystallographic orientations facilitates a new path to develop millimeter wave resonators with high figures of merit, low insertion loss, and miniature footprints, enabling new applications in millimeter wave signal processing and computing.

physics.app-ph↗

arXiv2024

Low-Loss Higher-Order Cross-Sectional Lam\'e Mode SAW Devices in 10-20 GHz Range

This paper presents surface acoustic wave (SAW) acoustic delay lines (ADL) for studying propagation loss mechanisms in Lithium Niobate (LN). Devices were fabricated by depositing 50 nm aluminum patterns on 600 nm X-Cut LN on amorphous silicon on silicon carbide, where longitudinally dominant SAW was targeted. Upon fabrication, higher-order thickness-based cross-sectional Lam\'e modes and Rayleigh modes were studied for their Q factors using acoustic delay lines. Utilizing bi-directional electrodes, ADL with lateral lambda values ranging from 0.4 um to 0.6 um were measured. Higher order Lame modes were found to have consistently higher Q factors than their Rayleigh mode counterpart, on the order of 1000-3000, showing high-frequency SAW devices as still viable candidates for frequency scaling without a substantial increase in loss.

physics.app-ph↗

arXiv2024

18 GHz Solidly Mounted Resonator in Scandium Aluminum Nitride on SiO2/Ta2O5 Bragg Reflector

This work reports an acoustic solidly mounted resonator (SMR) at 18.64 GHz, among the highest operating frequencies reported. The device is built in scandium aluminum nitride (ScAlN) on top of silicon dioxide (SiO2) and tantalum pentoxide (Ta2O5) Bragg reflectors on silicon (Si) wafer. The stack is analyzed with X-ray reflectivity (XRR) and high-resolution X-ray diffraction (HRXRD). The resonator shows a coupling coefficient (k2) of 2.0%, high series quality factor (Qs) of 156, shunt quality factor (Qp) of 142, and maximum Bode quality factor (Qmax) of 210. The third-order harmonics at 59.64 GHz is also observed with k2 around 0.6% and Q around 40. Upon further development, the reported acoustic resonator platform can enable various front-end signal-processing functions, e.g., filters and oscillators, at future frequency range 3 (FR3) bands.

physics.app-ph↗

arXiv2024

2 to 16 GHz Fundamental Symmetric Mode Acoustic Resonators in Piezoelectric Thin-Film Lithium Niobate

As 5G connectivity proliferates, signal processing applications at 6G centimeter bands have gained attention for urban wireless capacity expansion. At sub-5 GHz, acoustic resonators operating in the fundamental symmetric (S0) Lamb mode hold significant promise if frequency scaled to the 6G centimeter bands. Concurrently, the lateral wavelength dependency and the traveling wave nature of S0 mode enable monolithic multi-frequency fabrication, transversal filters, correlators, and other compact signal processing components. In this work, we present thin-film lithium niobate (LN) S0 resonators scaled up to 16 GHz. Specifically, we study the characteristics of the S0 mode as the wavelength is minimized and showcase a device at 14.9 GHz with a Bode Q maximum of 391, a k2 of 6%, and a figure of merit (FoM) of 23.33, surpassing the state-of-the-art (SoA) in its frequency range.

physics.app-ph↗

arXiv2024

Experimental Study of Periodically Poled Piezoelectric Film Lithium Niobate Resonator at Cryogenic Temperatures

This work reports the first study of periodically poled piezoelectric film (P3F) lithium niobate (LiNbO3) resonators at cryogenic temperatures. We experimentally investigate the temperature dependency of resonant frequencies and quality factor (Q) of higher-order Lamb modes up to 20 GHz between 80{\deg}K and 297{\deg}K, using a tri-layer P3F LiNbO3 resonators as the experimental platform. The supported thickness-shear Lamb modes between second-order symmetric (S2) and eleventh-order antisymmetric (A11) modes show temperature coefficients of frequency (TCF) averaging -68.8 ppm/K. Higher Q and more pronounced spurious modes are observed at lower temperatures for many modes. Upon further study, the cryogenic study will be crucial for identifying dominant loss mechanisms and origins of spurious modes in higher-order Lamb wave devices for millimeter-wave applications.

physics.app-ph↗

arXiv2024

C-Band Lithium Niobate on Silicon Carbide SAW Resonator With Figure-of-Merit of 124 at 6.5 GHz

In this work, we demonstrate a C-band shear-horizontal surface acoustic wave (SH-SAW) resonator with high electromechanical coupling (kt2) of 22% and a quality factor (Q) of 565 based on a thin-film lithium niobate (LN) on silicon carbide (SiC) platform, featuring an excellent figure-of-merit (FoM = kt2*Q ) of 124 at 6.5 GHz, the highest FoM reported in this frequency range. The resonator frequency upscaling is achieved through wavelength ($\lambda$) reduction and the use of thin aluminum (Al) electrodes. The LN/SiC waveguide and synchronous resonator design collectively enable effective acoustic energy confinement for a high FoM, even when the normalized thickness of LN approaches a scale of 0.5$\lambda$ to 1$\lambda$. To perform a comprehensive study, we also designed and fabricated five additional resonators, expending the $\lambda$ studied ranging from 480 to 800 nm, in the same 500 nm-thick transferred Y-cut thin-film LN on SiC. The fabricated SH-SAW resonators, operating from 5 to 8 GHz, experimentally demonstrate a kt2 from 20.3% to 22.9% and a Q from 350 to 575, thereby covering the entire C-band with excellent performance.

eess.SP↗

arXiv2024

23.8-GHz Acoustic Filter in Periodically Poled Piezoelectric Film Lithium Niobate With 1.52-dB IL and 19.4% FBW

This paper reports the first piezoelectric acoustic filter in periodically poled piezoelectric film (P3F) lithium niobate (LiNbO3) at 23.8 GHz with low insertion loss (IL) of 1.52 dB and 3-dB fractional bandwidth (FBW) of 19.4%. The filter features a compact footprint of 0.64 mm2. The third-order ladder filter is implemented with electrically coupled resonators in 150 nm bi-layer P3F 128 rotated Y-cut LiNbO3 thin film, operating in second-order symmetric (S2) Lamb mode. The record-breaking performance is enabled by the P3F LiNbO3 platform, where piezoelectric thin films of alternating orientations are transferred subsequently, facilitating efficient higher-order Lamb mode operation with simultaneously high quality factor (Q) and coupling coefficient (k2) at millimeter-wave (mmWave). Also, the multi-layer P3F stack promises smaller footprints and better nonlinearity than single-layer counterparts, thanks to the higher capacitance density and lower thermal resistance. Upon further development, the reported P3F LiNbO3 platform is promising for compact filters at mmWave.

physics.app-ph↗

arXiv2024

Thin-film Lithium Niobate on Insulator Surface Acoustic Wave Devices for 6G Centimeter Bands

In this work, we investigate the frequency scaling of shear-horizontal (S.H.) surface acoustic wave (SAW) resonators based on a lithium niobate on insulator (LNOI) substrate into the centimeter bands for 6G wireless systems. Prototyped resonators with wavelengths ranging between 240 nm and 400 nm were fabricated, and the experimental results exhibit a successful frequency scaling between 9.05 and 13.37 GHz. However, a noticeable performance degradation can be observed as the resonance frequency (fs) scales. Such an effect is expected to be caused by non-ideal helec/{\lambda} for smaller {\lambda} devices. The optimized LNOI SH-SAW with a {\lambda} of 400 nm exhibits a fs of 9.05 GHz, a keff2 of 15%, Qmax of 213 and a FoM of 32, which indicates a successful implementation for device targeting centimeter bands.

eess.SP↗

arXiv2023

Millimeter Wave Thin-Film Bulk Acoustic Resonator in Sputtered Scandium Aluminum Nitride Using Platinum Electrodes

This work describes sputtered scandium aluminum nitride (ScAlN) thin-film bulk acoustic resonators (FBAR) at millimeter wave (mmWave) with high quality factor (Q) using platinum (Pt) electrodes. FBARs with combinations of Pt and aluminum (Al) electrodes, i.e., Al top Al bottom, Pt top Al bottom, Al top Pt bottom, and Pt top Pt bottom, are built to study the impact of electrodes on mmWave FBARs. The demonstrated FBAR with Pt top and bottom electrodes achieve electromechanical coupling (k2) of 4.0% and Q of 116 for the first-order symmetric (S1) mode at 13.7 GHz, and k2 of 1.8% and Q of 94 for third-order symmetric (S3) mode at 61.6 GHz. Through these results, we confirmed that even in the frequency band of approximately 60 GHz, ScAlN FBAR can achieve a Q factor approaching 100 with optimized fabrication and acoustic/EM design. Further development calls for stacks with better quality in piezoelectric and metallic layers.

eess.SP↗

arXiv2023

Transferred Thin Film Lithium Niobate as Millimeter Wave Acoustic Filter Platforms

This paper reports the first high-performance acoustic filters toward millimeter wave (mmWave) bands using transferred single-crystal thin film lithium niobate (LiNbO3). By transferring LiNbO3 on the top of silicon (Si) and sapphire (Al2O3) substrates with an intermediate amorphous Si (aSi) bonding and sacrificial layer, we demonstrate compact acoustic filters with record-breaking performance beyond 20 GHz. In the LN-aSi-Al2O3 platform, the third-order ladder filter exhibits low insertion loss (IL) of 1.62 dB and 3-dB fractional bandwidth (FBW) of 19.8% at 22.1 GHz, while in the LN-aSi-Si platform, the filter shows low IL of 2.38 dB and FBW of 18.2% at 23.5 GHz. Material analysis validates the great crystalline quality of the stacks. The high-resolution x-ray diffraction (HRXRD) shows full width half maximum (FWHM) of 53 arcsec for Al2O3 and 206 arcsec for Si, both remarkably low compared to piezoelectric thin films of similar thickness. The reported results bring the state-of-the-art (SoA) of compact acoustic filters to much higher frequencies, and highlight transferred LiNbO3 as promising platforms for mmWave filters in future wireless front ends.

eess.SP↗

arXiv2023

38.7 GHz Thin Film Lithium Niobate Acoustic Filter

In this work, a 38.7 GHz acoustic wave ladder filter exhibiting insertion loss (IL) of 5.63 dB and 3-dB fractional bandwidth (FBW) of 17.6% is demonstrated, pushing the frequency limits of thin-film piezoelectric acoustic filter technology. The filter achieves operating frequency up to 5G millimeter wave (mmWave) frequency range 2 (FR2) bands, by thinning thin-film LiNbO3 resonators to sub-50 nm thickness. The high electromechanical coupling (k2) and quality factor (Q) of first-order antisymmetric (A1) mode resonators in 128 Y-cut lithium niobate (LiNbO3) collectively enable the first acoustic filters at mmWave. The key design consideration of electromagnetic (EM) resonances in interdigitated transducers (IDT) is addressed and mitigated. These results indicate that thin-film piezoelectric resonators could be pushed to 5G FR2 bands. Further performance enhancement and frequency scaling calls for better resonator technologies and EM-acoustic filter co-design.

eess.SP↗

arXiv2023

Millimeter Wave Thin-Film Bulk Acoustic Resonator in Sputtered Scandium Aluminum Nitride

This work reports a millimeter wave (mmWave) thin-film bulk acoustic resonator (FBAR) in sputtered scandium aluminum nitride (ScAlN). This paper identifies challenges of frequency scaling sputtered ScAlN into mmWave and proposes a stack and new fabrication procedure with a sputtered Sc0.3Al0.7N on Al on Si carrier wafer. The resonator achieves electromechanical coupling (k2) of 7.0% and quality factor (Q) of 62 for the first-order symmetric (S1) mode at 21.4 GHz, along with k2 of 4.0% and Q of 19 for the third-order symmetric (S3) mode at 55.4 GHz, showing higher figures of merit (FoM, k2xQ) than reported AlN/ScAlN-based mmWave acoustic resonators. The ScAlN quality is identified by transmission electron microscopy (TEM) and X-ray diffraction (XRD), identifying the bottlenecks in the existing piezoelectric-metal stack. Further improvement of ScAlN/AlN-based mmWave acoustic resonators calls for better crystalline quality from improved thin-film deposition methods.

eess.SP↗