Searcharxiv⌕ Search

arXiv subjects

Stefan Ballmer

Publications and source records attributed to Stefan Ballmer.

At least 19 recordsLinked to original sources
arXiv2026

Birefringence of AlGaAs/GaAs Coatings under Above-Band-Gap Illumination, GR Noise and Photo-Optic Transfer Function

AlGaAs/GaAs coatings are being considered as coating candidates for gravitational-wave detectors. In this paper we investigate the birefringence properties of this crystalline semiconductor material by modulating the optical illumination on the mirror coating and monitoring the induced birefringence. While the measured low-frequency birefringence values align with previous studies, we observed a frequency-dependent behavior in the illumination-to-birefringence coupling, characterized by a pole increasing with illumination intensity and a gain at zero frequency (DC gain) decreasing with illumination intensity. We developed a generic theoretical model based on a master equation to characterize the measurement results by considering photon-induced electric fields and electro-optic effects. This model can fit the frequency and intensity dependencies of the induced birefringence. Additionally, this model predicts a generation-recombination noise (GR noise) will be observable in the coating birefringence. While the presented measurement cannot predict the exact level of GR noise, for the frequency band and spot sizes relevant for gravitational-wave detectors we expect GR noise to be white below the pole frequency, scale with power the same way laser shot noise does, and for fixed power be independent of spot size.

physics.ins-det↗
arXiv2026

Combined Cavity Alignment and Mode-Mismatch Sensing using RF-QPD Sensors

In this article we describe a scheme for sensing both the mode mismatch and alignment of a cavity which does not require custom sensors and uses only Quadrant Photo-Detectors (QPDs). The technique is simple relying upon cylindrical lenses and thoughtful Gouy phase telescope design, and is trivial to implement alongside a Pound-Drever-Hall (PDH) locking scheme. The Gouy phase telescope design utilizes all three of the QPDs to sense each degree of freedom which also increases sensitivity and provides redundancy. The technique we show also works without RF modulation, which is useful for providing other general diagnostic information in complex optical experiments. An analytical overview of the technique as well as generic design equations for the Gouy phase telescope is provided. Finally, a detailed optical simulation is presented to verify the technique.

physics.optics↗
arXiv2024

Squeezing the quantum noise of a gravitational-wave detector below the standard quantum limit

Precision measurements of space and time, like those made by the detectors of the Laser Interferometer Gravitational-wave Observatory (LIGO), are often confronted with fundamental limitations imposed by quantum mechanics. The Heisenberg uncertainty principle dictates that the position and momentum of an object cannot both be precisely measured, giving rise to an apparent limitation called the Standard Quantum Limit (SQL). Reducing quantum noise below the SQL in gravitational-wave detectors, where photons are used to continuously measure the positions of freely falling mirrors, has been an active area of research for decades. Here we show how the LIGO A+ upgrade reduced the detectors' quantum noise below the SQL by up to 3 dB while achieving a broadband sensitivity improvement, more than two decades after this possibility was first presented.

gr-qc↗
arXiv2024

Criteria for identifying and evaluating locations that could potentially host the Cosmic Explorer observatories

Cosmic Explorer (CE) is a next-generation ground-based gravitational-wave observatory that is being designed in the 2020s and is envisioned to begin operations in the 2030s together with the Einstein Telescope in Europe. The CE concept currently consists of two widely separated L-shaped observatories in the United States, one with 40 km-long arms and the other with 20 km-long arms. This order of magnitude increase in scale with respect to the LIGO-Virgo-KAGRA observatories will, together with technological improvements, deliver an order of magnitude greater astronomical reach, allowing access to gravitational waves from remnants of the first stars and opening a wide discovery aperture to the novel and unknown. In addition to pushing the reach of gravitational-wave astronomy, CE endeavors to approach the lifecycle of large scientific facilities in a way that prioritizes mutually beneficial relationships with local and Indigenous communities. This article describes the (scientific, cost and access, and social) criteria that will be used to identify and evaluate locations that could potentially host the CE observatories.

physics.ins-det↗
arXiv2023

Cosmic Explorer: A Submission to the NSF MPSAC ngGW Subcommittee

Gravitational-wave astronomy has revolutionized humanity's view of the universe, a revolution driven by observations that no other field can make. This white paper describes an observatory that builds on decades of investment by the National Science Foundation and that will drive discovery for decades to come: Cosmic Explorer. Major discoveries in astronomy are driven by three related improvements: better sensitivity, higher precision, and opening new observational windows. Cosmic Explorer promises all three and will deliver an order-of-magnitude greater sensitivity than LIGO. Cosmic Explorer will push the gravitational-wave frontier to almost the edge of the observable universe using technologies that have been proven by LIGO during its development. With the unprecedented sensitivity that only a new facility can deliver, Cosmic Explorer will make discoveries that cannot yet be anticipated, especially since gravitational waves are both synergistic with electromagnetic observations and can reach into regions of the universe that electromagnetic observations cannot explore. With Cosmic Explorer, scientists can use the universe as a laboratory to test the laws of physics and study the nature of matter. Cosmic Explorer allows the United States to continue its leading role in gravitational-wave science and the international network of next-generation observatories. With its extraordinary discovery potential, Cosmic Explorer will deliver revolutionary observations across astronomy, physics, and cosmology including: Black Holes and Neutron Stars Throughout Cosmic Time, Multi-Messenger Astrophysics and Dynamics of Dense Matter, New Probes of Extreme Astrophysics, Fundamental Physics and Precision Cosmology, Dark Matter and the Early Universe.

astro-ph.IM↗
arXiv2022

Science-Driven Tunable Design of Cosmic Explorer Detectors

Ground-based gravitational-wave detectors like Cosmic Explorer can be tuned to improve their sensitivity at high or low frequencies by tuning the response of the signal extraction cavity. Enhanced sensitivity above 2 kHz enables measurements of the post-merger gravitational-wave spectrum from binary neutron star mergers, which depends critically on the unknown equation of state of hot, ultra-dense matter. Improved sensitivity below 500 Hz favors precision tests of extreme gravity with black hole ringdown signals and improves the detection prospects while facilitating an improved measurement of source properties for compact binary inspirals at cosmological distances. At intermediate frequencies, a more sensitive detector can better measure the tidal properties of neutron stars. We present and characterize the performance of tuned Cosmic Explorer configurations that are designed to optimize detections across different astrophysical source populations. These tuning options give Cosmic Explorer the flexibility to target a diverse set of science goals with the same detector infrastructure. We find that a 40 km Cosmic Explorer detector outperforms a 20 km in all key science goals other than access to post-merger physics. This suggests that Cosmic Explorer should include at least one 40 km facility.

gr-qc↗
arXiv2022

Next Generation Observatories -- Report from the Dawn VI Workshop; October 5-7 2021

The workshop Dawn VI: Next Generation Observatories took place online over three days, 5-7 October, 2021. More than 200 physicists and astronomers attended to contribute to, and learn from, a discussion of next-generation ground-based gravitational-wave detectors. The program was centered on the next generation of ground-based gravitational-wave observatories and their synergy with the greater landscape of scientific observatories of the 2030s. Cosmic Explorer (CE), a concept developed with US National Science Foundation support, was a particular focus; Einstein Telescope (ET), the European next generation concept, is an important complement and partner in forming a network. The concluding summary of the meeting expressed the sentiment that the observational science accessible to CE and ET, also in combination with data from other non-GW observatories, will stimulate a very broad community of analysts and yield insights which are exciting given the access to GWs from the entire universe. The need, and desire, for closer collaboration between ET and CE was expressed; a three-detector network is optimal for delivering much of the science. The science opportunities afforded by CE and ET are broad and compelling, impacting a wide range of disciplines in physics and high energy astrophysics. There was a consensus that CE is a concept that can deliver the promised science. A strong endorsement of Cosmic Explorer, as described in the CE Horizon Study, is a primary outcome of DAWN VI.

astro-ph.IM↗
arXiv2022

Piezo-deformable Mirrors for Active Mode Matching in Advanced LIGO

The detectors of the laser interferometer gravitational-wave observatory (LIGO) are broadly limited by the quantum noise and rely on the injection of squeezed states of light to achieve their full sensitivity. Squeezing improvement is limited by mode mismatch between the elements of the squeezer and the interferometer. In the current LIGO detectors, there is no way to actively mitigate this mode mismatch. This paper presents a new deformable mirror for wavefront control that meets the active mode matching requirements of advanced LIGO. The active element is a piezo-electric transducer, which actuates on the radius of curvature of a 5 mm thick mirror via an axisymmetric flexure. The operating range of the deformable mirror is 120+-8 mD in vacuum, with an additional 200 mD adjustment range accessible out of vacuum. The scattering into higher-order modes is measured to be <0.2% over the nominal beam radius. These piezo-deformable mirrors meet the stringent noise and vacuum requirements of advanced LIGO and will be used for the next observing run (O4) to control the mode-matching between the squeezer and the interferometer.

astro-ph.IM↗
arXiv2021

Gravitational-wave physics with Cosmic Explorer: limits to low-frequency sensitivity

Cosmic Explorer (CE) is a next-generation ground-based gravitational-wave observatory concept, envisioned to begin operation in the 2030s, and expected to be capable of observing binary neutron star and black hole mergers back to the time of the first stars. Cosmic Explorer's sensitive band will extend below 10 Hz, where the design is predominantly limited by geophysical, thermal, and quantum noises. In this work, thermal, seismic, gravity-gradient, quantum, residual gas, scattered-light, and servo-control noises are analyzed in order to motivate facility and vacuum system design requirements, potential test mass suspensions, Newtonian noise reduction strategies, improved inertial sensors, and cryogenic control requirements. Our analysis shows that with improved technologies, Cosmic Explorer can deliver a strain sensitivity better than $10^{-23}/\mathrm{Hz}^{1/2}$ down to 5 Hz. Our work refines and extends previous analysis of the Cosmic Explorer concept and outlines the key research areas needed to make this observatory a reality.

gr-qc↗
arXiv2020

Can we use next-generation gravitational wave detectors for terrestrial precision measurements of Shapiro delay?

Shapiro time delay is one of the fundamental tests of general relativity and post-Newtonian theories of gravity. Consequently, its measurements can be used to probe the parameter $γ$ which is related to spacetime curvature produced by a unit mass in the post-Newtonian formalism of gravity. To date all measurements of time delay have been conducted on astronomical scales. It was asserted in 2010 that gravitational wave detectors on Earth could be used to measure Shapiro delay on a terrestrial scale via massive rotating systems. Building on that work, we consider how measurements of Shapiro delay can be made using next-generation gravitational wave detectors. We perform an analysis for measuring Shapiro delay with the next-generation gravitational wave detectors Cosmic Explorer and Einstein Telescope to determine how precisely the effect can be measured. Using a rotating mass unit design, we find that Cosmic Explorer and Einstein Telescope can measure the Shapiro delay signal with amplitude signal to noise ratios upwards of $\sim28 $ and $\sim43$ in 1 year of integration time, respectively. By measuring Shapiro delay with this technique, next-generation interferometers will allow for terrestrial measurements of $γ$ in the paramaterized post-Newtonian formalism of gravity with sub-percent precision.

gr-qc↗
arXiv2019

Detection Prospects of Core-Collapse Supernovae with Supernova-Optimized Third-Generation Gravitational-wave Detectors

We optimize the third-generation gravitational-wave detector to maximize the range to detect core-collapse supernovae. Based on three-dimensional simulations for core-collapse and the corresponding gravitational-wave waveform emitted, the corresponding detection range for these waveforms is limited to within our galaxy even in the era of third-generation detectors. The corresponding event rate is two per century. We find from the waveforms that to detect core-collapse supernovae with an event rate of one per year, the gravitational-wave detectors need a strain sensitivity of 3$\times10^{-27}~$Hz$^{-1/2}$ in a frequency range from 100~Hz to 1500~Hz. We also explore detector configurations technologically beyond the scope of third-generation detectors. We find with these improvements, the event rate for gravitational-wave observations from CCSN is still low, but is improved to one in twenty years.

gr-qc↗
arXiv2015

Observation of Parametric Instability in Advanced LIGO

Parametric instabilities have long been studied as a potentially limiting effect in high-power interferometric gravitational wave detectors. Until now, however, these instabilities have never been observed in a kilometer-scale interferometer. In this work we describe the first observation of parametric instability in an Advanced LIGO detector, and the means by which it has been removed as a barrier to progress.

astro-ph.IM↗
arXiv2015

A Gravitational Wave Detector with Cosmological Reach

Twenty years ago, construction began on the Laser Interferometer Gravitational-wave Observatory (LIGO). Advanced LIGO, with a factor of ten better design sensitivity than Initial LIGO, will begin taking data this year, and should soon make detections a monthly occurrence. While Advanced LIGO promises to make first detections of gravitational waves from the nearby universe, an additional factor of ten increase in sensitivity would put exciting science targets within reach by providing observations of binary black hole inspirals throughout most of the history of star formation, and high signal to noise observations of nearby events. Design studies for future detectors to date rely on significant technological advances that are futuristic and risky. In this paper we propose a different direction. We resurrect the idea of a using longer arm lengths coupled with largely proven technologies. Since the major noise sources that limit gravitational wave detectors do not scale trivially with the length of the detector, we study their impact and find that 40~km arm lengths are nearly optimal, and can incorporate currently available technologies to detect gravitational wave sources at cosmological distances $(z \gtrsim 7)$.

astro-ph.IM↗
arXiv2014

Precise Measurement of Laser Power using an Optomechanical System

This paper shows a novel method to precisely measure the laser power using an optomechanical system. By measuring a mirror displacement caused by the reflection of an amplitude modulated laser beam, the number of photons in the incident continuous-wave laser can be precisely measured. We have demonstrated this principle by means of a prototype experiment uses a suspended 25 mg mirror as an mechanical oscillator coupled with the radiation pressure and a Michelson interferometer as the displacement sensor. A measurement of the laser power with an uncertainty of less than one percent (1 sigma) is achievable.

physics.ins-det↗
arXiv2014

Comparing Finesse simulations, analytical solutions and OSCAR simulations of Fabry-Perot alignment signals

This document records the results of a comparison of the interferometer simulation Finesse against an analytic (MATLAB based) calculation of the alignment sensing signals of a Fabry Perot cavity. This task was started during the commissioning workshop at the LIGO Livingston site between the 28.1. and 1.02 2013 with the aim of creating a reference example for validating numerical simulation tools. The FFT based simulation OSCAR joined the battle later.

physics.optics↗
arXiv2011

Optimal Alignment Sensing of a Readout Mode Cleaner Cavity

Critically coupled resonant optical cavities are often used as mode cleaners in optical systems to improve the signal to noise ratio (SNR) of a signal that is encoded as an amplitude modulation of a laser beam. Achieving the best SNR requires maintaining the alignment of the mode cleaner relative to the laser beam on which the signal is encoded. An automatic alignment system which is primarily sensitive to the carrier field component of the beam will not, in general, provide optimal SNR. We present an approach that modifies traditional dither alignment sensing by applying a large amplitude modulation on the signal field, thereby producing error signals that are sensitive to the signal sideband field alignment. When used in conjunction with alignment actuators, this approach can improve the detected SNR; we demonstrate a factor of 3 improvement in the SNR of a kilometer-scale detector of the Laser Interferometer Gravitational-wave Observatory. This approach can be generalized to other types of alignment sensors.

physics.optics↗
arXiv2009

Probing the anisotropies of a stochastic gravitational-wave background using a network of ground-based laser interferometers

We present a maximum-likelihood analysis for estimating the angular distribution of power in an anisotropic stochastic gravitational-wave background using ground-based laser interferometers. The standard isotropic and gravitational-wave radiometer searches (optimal for point sources) are recovered as special limiting cases. The angular distribution can be decomposed with respect to any set of basis functions on the sky, and the single-baseline, cross-correlation analysis is easily extended to a network of three or more detectors-that is, to multiple baselines. A spherical harmonic decomposition, which provides maximum-likelihood estimates of the multipole moments of the gravitational-wave sky, is described in detail. We also discuss: (i) the covariance matrix of the estimators and its relationship to the detector response of a network of interferometers, (ii) a singular-value decomposition method for regularizing the deconvolution of the detector response from the measured sky map, (iii) the expected increase in sensitivity obtained by including multiple baselines, and (iv) the numerical results of this method when applied to simulated data consisting of both point-like and di#use sources. Comparisions between this general method and the standard isotropic and radiometer searches are given throughout, to make contact with the existing literature on stochastic background searches.

astro-ph.IM↗