arXiv subjects

Sven Jacobsson

Publications and source records attributed to Sven Jacobsson.

At least 19 recordsLinked to original sources

arXiv2024

EVM Analysis of Distributed Massive MIMO with 1-Bit Radio-Over-Fiber Fronthaul

We analyze the uplink performance of a distributed massive multiple-input multiple-output (MIMO) architecture in which the remotely located access points (APs) are connected to a central processing unit via a fiber-optical fronthaul carrying a dithered and 1-bit quantized version of the received radio-frequency (RF) signal. The innovative feature of the proposed architecture is that no down-conversion is performed at the APs. This eliminates the need to equip the APs with local oscillators, which may be difficult to synchronize. Under the assumption that a constraint is imposed on the amount of data that can be exchanged across the fiber-optical fronthaul, we investigate the tradeoff between spatial oversampling, defined in terms of the total number of APs, and temporal oversampling, defined in terms of the oversampling factor selected at the central processing unit, to facilitate the recovery of the transmitted signal from 1-bit samples of the RF received signal. Using the so-called error-vector magnitude (EVM) as performance metric, we shed light on the optimal design of the dither signal, and quantify, for a given number of APs, the minimum fronthaul rate required for our proposed distributed massive MIMO architecture to outperform a standard co-located massive MIMO architecture in terms of EVM.

cs.IT↗

arXiv2024

A TDD Distributed MIMO Testbed Using a 1-Bit Radio-Over-Fiber Fronthaul Architecture

We present the uplink and downlink of a time-division duplex distributed multiple-input multiple-output (D-MIMO) testbed, based on a 1-bit radio-over-fiber architecture, which is low-cost and scalable. The proposed architecture involves a central unit (CU) that is equipped with 1-bit digital-to-analog and analog-to-digital converters, operating at 10 GS/s. The CU is connected to multiple single-antenna remote radio heads (RRHs) via optical fibers, over which a binary RF waveform is transmitted. In the uplink, a binary RF waveform is generated at the RRHs by a comparator, whose inputs are the received RF signal and a suitably designed dither signal. In the downlink, a binary RF waveform is generated at the CU via bandpass sigma-delta modulation. Our measurement results show that low error-vector magnitude (EVM) can be achieved in both the uplink and the downlink, despite 1-bit sampling at the CU. Specifically, for point-to-point over-cable transmission between a single user equipment (UE) and a CU equipped with a single RRH, we report, for a 10 MBd signal using single-carrier 16QAM modulation, an EVM of 3.3% in the downlink, and of 4.5% in the uplink. We then consider a CU connected to 3 RRHs serving over the air 2 UEs, and show that, after over-the-air reciprocity calibration, a downlink zero-forcing precoder designed on the basis of uplink channel estimates at the CU, achieves an EVM of 6.4% and 10.9% at UE 1 and UE 2, respectively. Finally, we investigate the ability of the proposed architecture to support orthogonal frequency-division multiplexing (OFDM) waveforms, and its robustness against both in-band and out-of-band interference.

eess.SP↗

arXiv2021

Hybrid Jammer Mitigation for All-Digital mmWave Massive MU-MIMO

Low-resolution analog-to-digital converters (ADCs) simplify the design of millimeter-wave (mmWave) massive multi-user multiple-input multiple-output (MU-MIMO) basestations, but increase vulnerability to jamming attacks. As a remedy, we propose HERMIT (short for Hybrid jammER MITigation), a method that combines a hardware-friendly adaptive analog transform with a corresponding digital equalizer: The analog transform removes most of the jammer's energy prior to data conversion; the digital equalizer suppresses jammer residues while detecting the legitimate transmit data. We provide theoretical results that establish the optimal analog transform as a function of the user equipments' and the jammer's channels. Using simulations with mmWave channel models, we demonstrate the superiority of HERMIT compared both to purely digital jammer mitigation as well as to a recent hybrid method that mitigates jammer interference with a nonadaptive analog transform.

cs.IT↗

arXiv2021

Distortion-Aware Linear Precoding for Massive MIMO Downlink Systems with Nonlinear Power Amplifiers

We introduce a framework for linear precoder design over a massive multiple-input multiple-output downlink system in the presence of nonlinear power amplifiers (PAs). By studying the spatial characteristics of the distortion, we demonstrate that conventional linear precoding techniques steer nonlinear distortions towards the users. We show that, by taking into account PA nonlinearity, one can design linear precoders that reduce, and in single-user scenarios, even completely remove the distortion transmitted in the direction of the users. This, however, is achieved at the price of a reduced array gain. To address this issue, we present precoder optimization algorithms that simultaneously take into account the effects of array gain, distortion, multiuser interference, and receiver noise. Specifically, we derive an expression for the achievable sum rate and propose an iterative algorithm that attempts to find the precoding matrix which maximizes this expression. Moreover, using a model for PA power consumption, we propose an algorithm that attempts to find the precoding matrix that minimizes the consumed power for a given minimum achievable sum rate. Our numerical results demonstrate that the proposed distortion-aware precoding techniques provide significant improvements in spectral and energy efficiency compared to conventional linear precoders.

cs.IT↗

arXiv2021

Resolution-Adaptive All-Digital Spatial Equalization for mmWave Massive MU-MIMO

All-digital basestation (BS) architectures for millimeter-wave (mmWave) massive multi-user multiple-input multiple-output (MU-MIMO), which equip each radio-frequency chain with dedicated data converters, have advantages in spectral efficiency, flexibility, and baseband-processing simplicity over hybrid analog-digital solutions. For all-digital architectures to be competitive with hybrid solutions in terms of power consumption, novel signal-processing methods and baseband architectures are necessary. In this paper, we demonstrate that adapting the resolution of the analog-to-digital converters (ADCs) and spatial equalizer of an all-digital system to the communication scenario (e.g., the number of users, modulation scheme, and propagation conditions) enables orders-of-magnitude power savings for realistic mmWave channels. For example, for a 256-BS-antenna 16-user system supporting 1 GHz bandwidth, a traditional baseline architecture designed for a 64-user worst-case scenario would consume 23 W in 28 nm CMOS for the ADC array and the spatial equalizer, whereas a resolution-adaptive architecture is able to reduce the power consumption by 6.7x.

eess.SP↗

arXiv2020

Finite-Alphabet Wiener Filter Precoding for mmWave Massive MU-MIMO Systems

Power consumption of multi-user (MU) precoding is a major concern in all-digital massive MU multiple-input multiple-output (MIMO) base-stations with hundreds of antenna elements operating at millimeter-wave (mmWave) frequencies. We propose to replace part of the linear Wiener filter (WF) precoding matrix by a finite-alphabet WF precoding (FAWP) matrix, which enables the use of low-precision hardware that consumes low power and area. To minimize the performance loss of our approach, we present methods that efficiently compute FAWP matrices that best mimic the WF precoder. Our results show that FAWP matrices approach infinite-precision error-rate and error-vector magnitude performance with only 3-bit precoding weights, even when operating in realistic mmWave channels. Hence, FAWP is a promising approach to substantially reduce power consumption and silicon area in all-digital mmWave massive MU-MIMO systems.

cs.IT↗

arXiv2020

High-Bandwidth Spatial Equalization for mmWave Massive MU-MIMO with Processing-In-Memory

All-digital basestation (BS) architectures enable superior spectral efficiency compared to hybrid solutions in massive multi-user MIMO systems. However, supporting large bandwidths with all-digital architectures at mmWave frequencies is challenging as traditional baseband processing would result in excessively high power consumption and large silicon area. The recently-proposed concept of finite-alphabet equalization is able to address both of these issues by using equalization matrices that contain low-resolution entries to lower the power and complexity of high-throughput matrix-vector products in hardware. In this paper, we explore two different finite-alphabet equalization hardware implementations that tightly integrate the memory and processing elements: (i) a parallel array of multiply-accumulate (MAC) units and (ii) a bit-serial processing-in-memory (PIM) architecture. Our all-digital VLSI implementation results in 28nm CMOS show that the bit-serial PIM architecture reduces the area and power consumption up to a factor of 2x and 3x, respectively, when compared to a parallel MAC array that operates at the same throughput.

eess.SP↗

arXiv2020

Soft-Output Finite Alphabet Equalization for mmWAVE Massive MIMO

Next-generation wireless systems are expected to combine millimeter-wave (mmWave) and massive multi-user multiple-input multiple-output (MU-MIMO) technologies to deliver high data-rates. These technologies require the basestations (BSs) to process high-dimensional data at extreme rates, which results in high power dissipation and system costs. Finite-alphabet equalization has been proposed recently to reduce the power consumption and silicon area of uplink spatial equalization circuitry at the BS by coarsely quantizing the equalization matrix. In this work, we improve upon finite-alphabet equalization by performing unbiased estimation and soft-output computation for coded systems. By simulating a massive MU-MIMO system that uses orthogonal frequency-division multiplexing and per-user convolutional coding, we show that soft-output finite-alphabet equalization delivers competitive error-rate performance using only 1 to 3 bits per entry of the equalization matrix, even for challenging mmWave channels.

cs.IT↗

arXiv2020

Finite-Alphabet MMSE Equalization for All-Digital Massive MU-MIMO mmWave Communication

We propose finite-alphabet equalization, a new paradigm that restricts the entries of the spatial equalization matrix to low-resolution numbers, enabling high-throughput, low-power, and low-cost hardware equalizers. To minimize the performance loss of this paradigm, we introduce FAME, short for finite-alphabet minimum mean-square error (MMSE) equalization, which is able to significantly outperform a naive quantization of the linear MMSE matrix. We develop efficient algorithms to approximately solve the NP-hard FAME problem and showcase that near-optimal performance can be achieved with equalization coefficients quantized to only 1-3 bits for massive multi-user multiple-input multiple-output (MU-MIMO) millimeter-wave (mmWave) systems. We provide very-large scale integration (VLSI) results that demonstrate a reduction in equalization power and area by at least a factor of 3.9x and 5.8x, respectively.

cs.IT↗

arXiv2019

Massive MU-MIMO-OFDM Uplink with Hardware Impairments: Modeling and Analysis

We study the impact of hardware impairments at the base station (BS) of an orthogonal frequency-division multiplexing (OFDM)-based massive multiuser (MU) multiple-input multiple-output (MIMO) uplink system. We leverage Bussgang's theorem to develop accurate models for the distortions caused by nonlinear low-noise amplifiers, local oscillators with phase noise, and oversampling finite-resolution analog-to-digital converters. By combining the individual effects of these hardware models, we obtain a composite model for the BS-side distortion caused by nonideal hardware that takes into account its inherent correlation in time, frequency, and across antennas. We use this composite model to analyze the impact of BS-side hardware impairments on the performance of realistic massive MU-MIMO-OFDM uplink systems.

cs.IT↗

arXiv2019

Massive MU-MIMO-OFDM Uplink with Direct RF-Sampling and 1-Bit ADCs

Advances in analog-to-digital converter (ADC) technology have opened up the possibility to directly digitize wideband radio frequency (RF) signals, avoiding the need for analog down-conversion. In this work, we consider an orthogonal frequency-division multiplexing (OFDM)-based massive multi-user (MU) multiple-input multiple-output (MIMO) uplink system that relies on direct RF-sampling at the base station and digitizes the received RF signals with 1-bit ADCs. Using Bussgang's theorem, we provide an analytical expression for the error-vector magnitude (EVM) achieved by digital down-conversion and zero-forcing combining. Our results demonstrate that direct RF-sampling 1-bit ADCs enables low EVM and supports high-order constellations in the massive MU-MIMO-OFDM uplink.

cs.IT↗

arXiv2019

Distortion-Aware Linear Precoding for Millimeter-Wave Multiuser MISO Downlink

In this work, we propose an iterative scheme for computing a linear precoder that takes into account the impact of hardware impairments in the multiuser multiple-input single-output downlink. We particularly focus on the case when the transmitter is equipped with nonlinear power amplifiers. Using Bussgang's theorem, we formulate a lower bound on the achievable sum rate in the presence of hardware impairments, and maximize it using projected gradient ascent. We provide numerical examples that demonstrate the efficacy of the proposed distortion-aware scheme for precoding over a millimeter-wave~channel.

eess.SP↗

arXiv2019

Timing and Frequency Synchronization for 1-bit Massive MU-MIMO-OFDM Downlink

We consider timing and frequency synchronization for the massive multiuser (MU) multiple-input multiple-output (MIMO) downlink where 1-bit digital-to-analog converters (DACs) are used at the base station (BS). We focus on the practically relevant scenario in which orthogonal-frequency division multiplexing (OFDM) is used to communicate over frequency-selective channels. Our contributions are twofold. First, we use Bussgang's theorem to analyze the impact on performance caused by timing and frequency offsets in the presence of 1-bit DACs at the BS. Second, we demonstrate the efficacy of the widely used Schmidl-Cox synchronization algorithm. Our results demonstrate that the 1-bit massive MU-MIMO-OFDM downlink is resilient against timing and frequency offsets.

cs.IT↗

arXiv2019

Neural-Network Optimized 1-bit Precoding for Massive MU-MIMO

Base station (BS) architectures for massive multi-user (MU) multiple-input multiple-output (MIMO) wireless systems are equipped with hundreds of antennas to serve tens of users on the same time-frequency channel. The immense number of BS antennas incurs high system costs, power, and interconnect bandwidth. To circumvent these obstacles, sophisticated MU precoding algorithms that enable the use of 1-bit DACs have been proposed. Many of these precoders feature parameters that are, traditionally, tuned manually to optimize their performance. We propose to use deep-learning tools to automatically tune such 1-bit precoders. Specifically, we optimize the biConvex 1-bit PrecOding (C2PO) algorithm using neural networks. Compared to the original C2PO algorithm, our neural-network optimized (NNO-)C2PO achieves the same error-rate performance at $\bf 2\boldsymbol\times$ lower complexity. Moreover, by training NNO-C2PO for different channel models, we show that 1-bit precoding can be made robust to vastly changing propagation conditions.

cs.IT↗

arXiv2019

Linear Precoding with Low-Resolution DACs for Massive MU-MIMO-OFDM Downlink

We consider the downlink of a massive multiuser (MU) multiple-input multiple-output (MIMO) system in which the base station (BS) is equipped with low-resolution digital-to-analog converters (DACs). In contrast to most existing results, we assume that the system operates over a frequency-selective wideband channel and uses orthogonal frequency division multiplexing (OFDM) to simplify equalization at the user equipments (UEs). Furthermore, we consider the practically relevant case of oversampling DACs. We theoretically analyze the uncoded bit error rate (BER) performance with linear precoders (e.g., zero forcing) and quadrature phase-shift keying using Bussgang's theorem. We also develop a lower bound on the information-theoretic sum-rate throughput achievable with Gaussian inputs, which can be evaluated in closed form for the case of 1-bit DACs. For the case of multi-bit DACs, we derive approximate, yet accurate, expressions for the distortion caused by low-precision DACs, which can be used to establish lower bounds on the corresponding sum-rate throughput. Our results demonstrate that, for a massive MU-MIMO-OFDM system with a 128-antenna BS serving 16 UEs, only 3--4 DAC bits are required to achieve an uncoded BER of 10^-4 with a negligible performance loss compared to the infinite-resolution case at the cost of additional out-of-band emissions. Furthermore, our results highlight the importance of taking into account the inherent spatial and temporal correlations caused by low-precision DACs.

cs.IT↗

arXiv2018

Nonlinear Precoding for Phase-Quantized Constant-Envelope Massive MU-MIMO-OFDM

We propose a nonlinear phase-quantized constant-envelope precoding algorithm for the massive multi-user (MU) multiple-input multiple-output (MIMO) downlink. Specifically, we adapt the squared-infinity norm Douglas-Rachford splitting (SQUID) precoder to systems that use oversampling digital-to-analog converters (DACs) at the base station (BS) and orthogonal frequency-division multiplexing (OFDM) to communicate over frequency-selective channels. We demonstrate that the proposed SQUID-OFDM precoder is able to generate transmit signals that are constrained to constant envelope, which enables the use of power-efficient analog radio-frequency circuitry at the BS. By quantizing the phase of the resulting constant-envelope signal, we obtain a finite-cardinality transmit signal that can be synthesized by low-resolution (e.g., 1-bit) DACs. We use error-rate simulations to demonstrate the superiority of SQUID-OFDM over linear-quantized precoders for massive MU-MIMO-OFDM systems.

cs.IT↗

arXiv2018

MSE-optimal 1-bit Precoding for Multiuser MIMO via Branch and Bound

In this paper, we solve the sum mean-squared error (MSE)-optimal 1-bit quantized precoding problem exactly for small-to-moderate sized multiuser multiple-input multiple-output (MU-MIMO) systems via branch and bound. To this end, we reformulate the original NP-hard precoding problem as a tree search and deploy a number of strategies that improve the pruning efficiency without sacrificing optimality. We evaluate the error-rate performance and the complexity of the resulting 1-bit branch-and-bound (BB-1) precoder, and compare its efficacy to that of existing, suboptimal algorithms for 1-bit precoding in MU-MIMO systems.

cs.IT↗

arXiv2018

VLSI Design of a 3-bit Constant-Modulus Precoder for Massive MU-MIMO

Fifth-generation (5G) cellular systems will build on massive multi-user (MU) multiple-input multiple-output (MIMO) technology to attain high spectral efficiency. However, having hundreds of antennas and radio-frequency (RF) chains at the base station (BS) entails prohibitively high hardware costs and power consumption. This paper proposes a novel nonlinear precoding algorithm for the massive MU-MIMO downlink in which each RF chain contains an 8-phase (3-bit) constant-modulus transmitter, enabling the use of low-cost and power-efficient analog hardware. We present a high-throughput VLSI architecture and show implementation results on a Xilinx Virtex-7 FPGA. Compared to a recently-reported nonlinear precoder for BS designs that use two 1-bit digital-to-analog converters per RF chain, our design enables up to 3.75 dB transmit power reduction at no more than a 2.7x increase in FPGA resources.

eess.SP↗