arXiv subjects

T. Braun

Publications and source records attributed to T. Braun.

7 recordsLinked to original sources

arXiv2025

Sensitivity to low-mass WIMPs with an improved liquid argon ionization response model within the DarkSide programme

Dark matter detection experiments using liquid argon rely on a precise characterization of the ionization response to nuclear recoils, especially in the keV energy range relevant for light dark matter interactions. In this work, we present a comprehensive analysis that combines new measurements from the ReD setup, part of the DarkSide experimental program, with calibration data from DarkSide-50, as well as results from the ARIS and SCENE experiments. These combined datasets enable improved constraints on atomic screening effects in the modeling of the ionization response of liquid argon to nuclear recoils. The analysis is performed within the Thomas-Imel recombination framework adopted in previous DarkSide studies, and is here further constrained by the inclusion of ReD data, which allow the screening function to be determined from calibration measurements. By including the updated ionization model into the DarkSide-50 analysis framework, we obtain stronger exclusion limits on low-mass WIMP interactions, setting new world-leading constraints in the 1-3 GeV/c^2 WIMP mass range. Finally, we recast the sensitivity projections for the upcoming DarkSide-20k detector, demonstrating a significantly enhanced discovery potential for low-mass dark matter candidates.

hep-ex↗

arXiv2025

Production, Quality Assurance and Quality Control of the SiPM Tiles for the DarkSide-20k Time Projection Chamber

The DarkSide-20k dark matter direct detection experiment will employ a 21 m^2 silicon photomultiplier (SiPM) array, instrumenting a dual-phase 50 tonnes liquid argon Time Projection Chamber (TPC). SiPMs are arranged into modular photosensors called Tiles, each integrating 24 SiPMs onto a printed circuit board (PCB) that provides signal amplification, power distribution, and a single-ended output for simplified readout. 16 Tiles are further grouped into Photo-Detector Units (PDUs). This paper details the production of the Tiles and the quality assurance and quality control (QA-QC) protocol established to ensure their performance and uniformity. The production and QA-QC of the Tiles are carried out at Nuova Officina Assergi (NOA), an ISO-6 clean room facility at LNGS. This process includes wafer-level cryogenic characterisation, precision flip-chip bonding, wire bonding, and extensive electrical and optical validation of each Tile. The overall production yield exceeds 83.5%, matching the requirements of the DarkSide-20k production plan. These results validate the robustness of the Tile design and its suitability for operation in a cryogenic environment.

physics.ins-det↗

arXiv2021

Experiments conducted in the burning plasma regime with inertial fusion implosions

An experimental program is currently underway at the National Ignition Facility (NIF) to compress deuterium and tritium (DT) fuel to densities and temperatures sufficient to achieve fusion and energy gain. The primary approach being investigated is indirect drive inertial confinement fusion (ICF), where a high-Z radiation cavity (a hohlraum) is heated by lasers, converting the incident energy into x-ray radiation which in turn drives the DT fuel filled capsule causing it to implode. Previous experiments reported DT fuel gain exceeding unity [O.A. Hurricane et al., Nature 506, 343 (2014)] and then exceeding the kinetic energy of the imploding fuel [S. Le Pape et al., Phys. Rev. Lett. 120, 245003 (2018)]. We report on recent experiments that have achieved record fusion neutron yields on NIF, greater than 100 kJ with momentary fusion powers exceeding 1PW, and have for the first time entered the burning plasma regime where fusion alpha-heating of the fuel exceeds the energy delivered to the fuel via compression. This was accomplished by increasing the size of the high-density carbon (HDC) capsule, increasing energy coupling, while controlling symmetry and implosion design parameters. Two tactics were successful in controlling the radiation flux symmetry and therefore the implosion symmetry: transferring energy between laser cones via plasma waves, and changing the shape of the hohlraum. In conducting these experiments, we controlled for known sources of degradation. Herein we show how these experiments were performed to produce record performance, and demonstrate the data fidelity leading us to conclude that these shots have entered the burning plasma regime.

physics.plasm-ph↗

arXiv2019

Factorizations of surjective maps of connected quandles

We consider the problem of when one quandle homomorphism will factor through another, restricting our attention to the case where all quandles involved are connected. We provide a complete solution to the problem for surjective quandle homomorphisms using the structure theorem for connected quandles of Ehrman et al. (2008) and the factorization system for surjective quandle homomorphsims of Bunch et al. (2010) as our primary tools. The paper contains the substantive results obtained by an REU research group consisting of the first four authors under the mentorship of the fifth, and was supported by National Science Foundation, grant DMS-1659123.

math.GR↗

arXiv2016

Impact of ex-situ rapid thermal annealing on the magneto-optical properties and the oscillator strength of In(Ga)As quantum dots

We discuss the influence of a rapid thermal annealing step on the magneto-optical emission properties of In(Ga)As/GaAs quantum dots. We map out a strong influence of the growth- and anneling parameters on the quantum excitons' effective Landé g-factors and in particular on their diamagnetic coefficients, which we directly correlate with the modification of the emitters shape and material composition. In addition, we study the excitons' spontaneous emission lifetime as a function of the annealing temperature and the dot height, and observe a strong increase of the emission rate with the quantum dot volume. The corresponding increase in oscillator strenth yields fully consistent results with the analysis of the diamagenic behavior. In particular, we demonstrate that a rapid thermal annealing step of 850$^\circ$ C can be employed to increase the oscillator strength of as-grown InAs/GaAs QDs by more than a factor of $2$.

cond-mat.mes-hall↗

arXiv2015

Enhanced single photon emission from positioned InP/GaInP quantum dots coupled to a confined Tamm-plasmon mode

We report on the enhancement of the spontaneous emission in the visible red spectral range from site-controlled InP/GaInP quantum dots by resonant coupling to Tammplasmon modes confined beneath gold disks in a hybrid metal/semiconductor structure. The enhancement of the emission intensity is confirmed by spatially resolved microphotoluminescence area scans and temperature dependent measurements. Single photon emission from our coupled system is verified via second order autocorrelation measurements. We observe bright single quantum dot emission of up to ~173000 detected photons per second at a repetition rate of the excitation source of 82 MHz, and calculate an extraction efficiency of our device as high as 7%.

cond-mat.mes-hall↗

arXiv2008

Lamination And Microstructuring Technology for a Bio-Cell Multiwell array

Microtechnology becomes a versatile tool for biological and biomedical applications. Microwells have been established long but remained non-intelligent up to now. Merging new fabrication techniques and handling concepts with microelectronics enables to realize intelligent microwells suitable for future improved cancer treatment. The described technology depicts the basis for the fabrication of a elecronically enhanced microwell. Thin aluminium sheets are structured by laser micro machining and laminated successively to obtain registration tolerances of the respective layers of 5..10Â$μ$m. The microwells lasermachined into the laminate are with 50..80Â$μ$m diameter, allowing to hold individual cells within the well. The individual process steps are described and results on the microstructuring are given.

cs.OH↗