arXiv subjects

T. Tabarelli de Fatis

Publications and source records attributed to T. Tabarelli de Fatis.

18 recordsLinked to original sources

arXiv2026

Demonstrating the thermal noise limit in a backaction-free bulk acoustic wave resonator chain for gravitational wave detection

We report the full sub-Kelvin characterization of the BAUSCIA high-frequency gravitational-wave antenna, based on cryogenic Bulk Acoustic Wave resonators coupled to SQUID amplifiers for signal readout. The end-to-end performance analysis of the experimental chain, from the sensor to the DAQ, demonstrates that resonator thermal noise dominates the noise budget at temperatures well below 100 mK for all investigated modes. The measurements also verify proper thermalization of the resonator modes and rule out significant SQUID backaction on the strain sensor, confirming that the system operates close to its fundamental limits with comparable resonator thermal noise and additive readout noise. From this characterization, we derive projected strain sensitivities in the range $1$--$10 \times 10^{-21}\,\mathrm{Hz}^{-1/2}$ for several resonant frequencies between 5 and 20~MHz, with corresponding fundamental thermal limits in the range $0.7$--$1.4 \times 10^{-21}\,\mathrm{Hz}^{-1/2}$. Equipped with three resonators and synchronized to an absolute global time reference for multi-site coincidences, the antenna is ready to enter a pilot science run.

physics.ins-det↗

arXiv2025

An array of bulk-acoustic-wave sensors as a high-frequency antenna for gravitational waves

In their simplest form, bulk acoustic wave (BAW) devices consist of a piezoelectric crystal between two electrodes that transduce the material's vibrations into electrical signals. They are adopted in frequency control and metrology, with well-established standards at frequencies of 5~MHz and above. Their use as a resonant-mass strain antenna for high-frequency gravitational waves has been recently proposed (Goryachev and Tobar, 2014). The estimated power spectral density sensitivity at the resonant frequencies is of the order of $10^{-21}\, \textrm{strain}/\sqrt{\textrm{Hz}}$. In this paper, after introducing the science opportunity and potential of gravitational wave detection with BAWs, we describe the two-stage BAUSCIA project plan to build a multimode antenna based on commercial BAWs, followed by an optimized array of custom BAWs. We show that commercially available BAWs already provide sensitivity comparable to current experiments around 10~MHz. Finally, we outline options for optimization of custom devices to improve sensitivity in an unexplored region, probe multiple frequencies between 0.1 and 10 MHz, and target specific signals, such as post-merger emission from neutron stars or emission from various dark matter candidates.

physics.ins-det↗

arXiv2024

Optimization of LYSO crystals and SiPM parameters for the CMS MIP timing detector

For the High-Luminosity (HL-LHC) phase, the upgrade of the Compact Muon Solenoid (CMS) experiment at CERN will include a novel MIP Timing Detector (MTD). The central part of MTD, the barrel timing layer (BTL), is designed to provide a measurement of the time of arrival of charged particles with a precision of 30 ps at the beginning of HL-LHC, progressively degrading to 60 ps while operating in an extremely harsh radiation environment for over a decade. In this paper we present a comparative analysis of the time resolution of BTL module prototypes made of LYSO:Ce crystal bars read out by silicon photo-multipliers (SiPMs). The timing performance measured in beam test campaigns is presented for prototypes with different construction and operation parameters, such as different SiPM cell sizes (15, 20, 25 and 30 $\rm μm$), SiPM manufacturers and crystal bar thicknesses. The evolution of time resolution as a function of the irradiation level has been studied using non-irradiated SiPMs as well as SiPMs exposed up to $2\times 10^{14}~n_{eq}/cm^2$ fluence. The key parameters defining the module time resolution such as SiPM characteristics (gain, photon detection efficiency, radiation induced dark count rate) and crystal properties (light output and dimensions) are discussed. These results have informed the final choice of the MTD barrel sensor configuration and offer a unique starting point for the design of future large-area scintillator-based timing detectors in either low or high radiation environments.

physics.ins-det↗

arXiv2024

TOFHIR2: The readout ASIC of the CMS Barrel MIP Timing Detector

The CMS detector will be upgraded for the HL-LHC to include a MIP Timing Detector (MTD). The MTD will consist of barrel and endcap timing layers, BTL and ETL respectively, providing precision timing of charged particles. The BTL sensors are based on LYSO:Ce scintillation crystals coupled to SiPMs with TOFHIR2 ASICs for the front-end readout. A resolution of 30-60 ps for MIP signals at a rate of 2.5 Mhit/s per channel is expected along the HL-LHC lifetime. We present an overview of the TOFHIR2 requirements and design, simulation results and measurements with TOFHIR2 ASICs. The measurements of TOFHIR2 associated to sensor modules were performed in different test setups using internal test pulses or blue and UV laser pulses emulating the signals expected in the experiment. The measurements show a time resolution of 24 ps initially during Beginning of Operation (BoO) and 58 ps at End of Operation (EoO) conditions, matching well the BTL requirements. We also showed that the time resolution is stable up to the highest expected MIP rate. Extensive radiation tests were performed, both with x-rays and heavy ions, showing that TOFHIR2 is not affected by the radiation environment during the experiment lifetime.

physics.ins-det↗

arXiv2023

Integration of thermo-electric coolers into the CMS MTD SiPM arrays for operation under high neutron fluence

The barrel section of the novel MIP Timing Detector (MTD) will be constructed as part of the upgrade of the CMS experiment to provide a time resolution for single charged tracks in the range of $30-60$ ps using LYSO:Ce crystal arrays read out with Silicon Photomultipliers (SiPMs). A major challenge for the operation of such a detector is the extremely high radiation level, of about $2\times10^{14}$ 1 MeV(Si) Eqv. n/cm$^2$, that will be integrated over a decade of operation of the High Luminosity Large Hadron Collider (HL-LHC). Silicon Photomultipliers exposed to this level of radiation have shown a strong increase in dark count rate and radiation damage effects that also impact their gain and photon detection efficiency. For this reason during operations the whole detector is cooled down to about $-35^{\circ}$C. In this paper we illustrate an innovative and cost-effective solution to mitigate the impact of radiation damage on the timing performance of the detector, by integrating small thermo-electric coolers (TECs) on the back of the SiPM package. This additional feature, fully integrated as part of the SiPM array, enables a further decrease in operating temperature down to about $-45^{\circ}$C. This leads to a reduction by a factor of about two in the dark count rate without requiring additional power budget, since the power required by the TEC is almost entirely offset by a decrease in the power required for the SiPM operation due to leakage current. In addition, the operation of the TECs with reversed polarity during technical stops of the accelerator can raise the temperature of the SiPMs up to $60^{\circ}$C (about $50^{\circ}$C higher than the rest of the detector), thus accelerating the annealing of radiation damage effects and partly recovering the SiPM performance.

physics.ins-det↗

arXiv2017

Response of microchannel plates in ionization mode to single particles and electromagnetic showers

Hundreds of concurrent collisions per bunch crossing are expected at future hadron colliders. Precision timing calorimetry has been advocated as a way to mitigate the pileup effects and, thanks to their excellent time resolution, microchannel plates (MCPs) are good candidate detectors for this goal. We report on the response of MCPs, used as secondary emission detectors, to single relativistic particles and to electromagnetic showers. Several prototypes, with different geometries and characteristics, were exposed to particle beams at the INFN-LNF Beam Test Facility and at CERN. Their time resolution and efficiency are measured for single particles and as a function of the multiplicity of particles. Efficiencies between 50% and 90% to single relativistic particles are reached, and up to 100% in presence of a large number of particles. Time resolutions between 20ps and 30ps are obtained.

physics.ins-det↗

arXiv2015

Performance of a Tungsten-Cerium Fluoride Sampling Calorimeter in High-Energy Electron Beam Tests

A prototype for a sampling calorimeter made out of cerium fluoride crystals interleaved with tungsten plates, and read out by wavelength-shifting fibres, has been exposed to beams of electrons with energies between 20 and 150 GeV, produced by the CERN Super Proton Synchrotron accelerator complex. The performance of the prototype is presented and compared to that of a Geant4 simulation of the apparatus. Particular emphasis is given to the response uniformity across the channel front face, and to the prototype's energy resolution.

physics.ins-det↗

arXiv2015

Response of microchannel plates to single particles and to electromagnetic showers

We report on the response of microchannel plates (MCPs) to single relativistic particles and to electromagnetic showers. Particle detection by means of secondary emission of electrons at the MCP surface has long been proposed and is used extensively in ion time-of-flight mass spectrometers. What has not been investigated in depth is their use to detect the ionizing component of showers. The time resolution of MCPs exceeds anything that has been previously used in calorimeters and, if exploited effectively, could aid in the event reconstruction at high luminosity colliders. Several prototypes of photodetectors with the amplification stage based on MCPs were exposed to cosmic rays and to 491 MeV electrons at the INFN-LNF Beam-Test Facility. The time resolution and the efficiency of the MCPs are measured as a function of the particle multiplicity, and the results used to model the response to high-energy showers.

physics.ins-det↗

arXiv2009

A novel approach to background reduction in double beta decay experiments

Active background reduction in high resolution calorimeters is a promising approach to achieve ultimate sensitivity in neutrinoless double beta decay experiments. We propose Cerenkov emission from beta rays in bolometric crystals as a viable alternative to scintillation. This novel approach could broaden the range of materials of interest for calorimetric searches of the double beta decay. We discuss the optical properties of TeO$_2$ crystals, as a show case.

nucl-ex↗

arXiv2007

Neutrino hierarchy from CP-blind observables with high density magnetized detectors

High density magnetized detectors are well suited to exploit the outstanding purity and intensities of novel neutrino sources like Neutrino Factories and Beta Beams. They can also provide independent measurements of leptonic mixing parameters through the observation of atmospheric muon-neutrinos. In this paper, we discuss the combination of these observables from a multi-kton iron detector and a high energy Beta Beam; in particular, we demonstrate that even with moderate detector granularities the neutrino mass hierarchy can be determined for $θ_{13}$ values greater than 4$^\circ$.

hep-ph↗

arXiv2006

A Beta Beam complex based on the machine upgrades for the LHC

The Beta Beam CERN design is based on the present LHC injection complex and its physics reach is mainly limited by the maximum rigidity of the SPS. In fact, some of the scenarios for the machine upgrades of the LHC, particularly the construction of a fast cycling 1 TeV injector (``Super-SPS''), are very synergic with the construction of a higher $γ$ Beta Beam. At the energies that can be reached by this machine, we demonstrate that dense calorimeters can already be used for the detection of $ν$ at the far location. Even at moderate masses (40 kton) as the ones imposed by the use of existing underground halls at Gran Sasso, the CP reach is very large for any value of $θ_{13}$ that would provide evidence of $ν_e$ appearance at T2K or NO$ν$A ($θ_{13}\geq 3^\circ$). Exploitation of matter effects at the CERN to Gran Sasso distance provides sensitivity to the neutrino mass hierarchy in significant areas of the $θ_{13}-δ$ plane.

hep-ph↗

arXiv2006

A new concept for streamer quenching in resistive plate chambers

In this paper we propose a new concept for streamer quenching in Resistive Plate Chambers (RPCs). In our approach, the multiplication process is quenched by the appropriate design of a mechanical structure inserted between the two resistive electrodes. We show that stable performance is achieved with binary gas mixtures based on argon and a small fraction of isobutane. Fluorocarbons, deemed responsible for the degradation of the electrode inner surface of RPC detectors, are thus fully eliminated from the gas mixture. This design {also resulted} in a simplified assembly procedure. Preliminary results obtained with a few prototypes of ``Mechanically Quenched RPCs'' and some prospects for future developments are discussed.

physics.ins-det↗

arXiv2005

Perspectives for a neutrino program based on the upgrades of the CERN accelerator complex

In this paper, we discuss the possibilities offered to neutrino physics by the upgrades of the CERN accelerator complex. Emphasis is on the physics reach of a medium $γ$ (350-580) $β$-beam that fully exploits the improvements in the CERN accelerator complex for the luminosity/energy upgrade of the LHC. We show that, this design not only profits of the ongoing efforts for the upgrades of the LHC, but also leverage out the existing infrastructures of the LNGS underground laboratory. Furthermore, given the involved high neutrino energies, above 1 GeV, a non-magnetized iron detector could efficiently exploit the neutrino beam. We show that the performance of this complex for what concerns the discovery of the CP violation in the leptonic sector, in case $θ_{13}$ is discovered by Phase I experiments, is comparable with the current baseline design based on a gigantic water Cherenkov at Frejus. Furthermore, this complex has also some sensitivity to the neutrino mass hierarchy.

hep-ph↗

arXiv2005

Digital Hadron Calorimetry with Glass RPC Active Detectors

Glass RPC detectors are an attractive candidate for the active part of a highly granular digital hadron calorimeter (DHCAL) at the ILC. A numerical study, based on the GEANT3 simulation package, of the performance of such a calorimeter is presented in this work. A simplified model for the RPC response, tuned on real data, is implemented in the simulation. The reliability of the simulation is demonstrated by comparison to existing data collected with a large volume calorimeter prototype exposed to a pion beam in an energy range from 2 GeV to 10 GeV. In view of an optimization of the readout pitch, a detailed study of the energy and position resolution at the single hadron level for different read-out pad dimensions is presented. These results are then used in a parametric form to obtain a preliminary estimate of the contribution of DHCAL to the reconstruction of the energy flow at the ILC detector.

physics.ins-det↗

arXiv2002

Future projects on atmospheric neutrinos

New results from Super-Kamiokande, K2K and SNO not only have spurred on the interest in neutrino oscillation physics, but also have started to shift the interest from discovery to precision measurements. Future projects focusing on atmospheric neutrinos are reviewed in this context. Important contributions could be made in the precision determination of the oscillation parameters, in the observation of matter effects and in the determination of the neutrino mass hierarchy. Unfortunately, the probability that the projects discussed in this review will be running in the next ten years is rather small. The only project with a shorter time scale has not been funded.

hep-ex↗

arXiv2002

Prospects of measuring $\sin^2 2Θ_{13}$ and the sign of $Δm^2$ with a massive magnetized detector for atmospheric neutrinos

The pattern of oscillation parameters emerging from current experimental data can be further elucidated by the observation of matter effects. In contrast to planned experiments with conventional neutrino beams, atmospheric neutrinos offer the possibility to search for Earth-induced matter effects with very long baselines. Resonant matter effects are asymmetric on neutrinos and anti-neutrinos, depending on the sign of $Δm^2$. In a three-generation oscillation scenario, this gives access to the mass hierarchy of neutrinos, while the size of the asymmetry would measure the admixture of electron neutrinos to muon/tau neutrino oscillations (the mixing angle $Θ_{13}$). The sensitivity to these effects is discussed after the detailed simulation of a realistic experiment based on a massive detector for atmospheric neutrinos with charge identification. We show how a detector, which measure and distinguish between $ν_μ$ and $\barν_μ$ charged current events, might be sensitive to matter effects using atmospheric neutrinos, provided the mixing angle $Θ_{13}$ is large enough.

hep-ph↗

arXiv2001

On particle production for high energy neutrino beams

Analytical formulae for the calculation of secondary particle yields in p-A interactions are given. These formulae can be of great practical importance for fast calculations of neutrino fluxes and for designing new neutrino beam-lines. The formulae are based on a parameterization of the inclusive invariant cross sections for secondary particle production measured in p-Be interactions. Data collected in different energy ranges and kinematic regions are used. The accuracy of the fit to the data with the empirical formulae adopted is within the experimental uncertainties. Prescriptions to extrapolate this parameterization to finite targets and to targets of different materials are given. The results obtained are then used as an input for the simulation of neutrino beams. We show that our approach describes well the main characteristics of measured neutrino spectra at CERN. Thus it may be used in fast simulations aiming at the optimisation of the proposed long-baseline neutrino beams at CERN and FNAL. In particular we will show our predictions for the CNGS beam from CERN to Gran Sasso.

hep-ph↗

arXiv1999

Measurement of neutrino oscillations by means of a high density detector on the atmospheric neutrino beam

A high-density calorimeter, consisting of magnetized iron planes interleaved by RPCs, as tracking and timing devices, is a good candidate for a next generation experiment on atmospheric neutrinos. With 34 kt of mass and in four years of data taking, this experiment will be sensitive to $ν_μ\to ν_x$ oscillation with $Δm^2 > 6 \times 10^{-5}$ and mixing near to maximal and fully cover the region of oscillation parameters suggested by Super-Kamiokande results. Moreover, the experimental method will enable to measure the oscillation parameters from the modulation of the L/E spectrum ($ν_μ$ disappearance). For $Δm^2 > 3 \times 10^{-3}$ eV$^2$, this experiment can also establish whether the oscillation occurs into a tau or a sterile neutrino, by looking for an excess of muon-less events at high energies produced by upward-going tau neutrinos ($ν_τ$ appearance).

hep-ex↗