arXiv subjects

Tage Christensen

Publications and source records attributed to Tage Christensen.

At least 19 recordsLinked to original sources

arXiv2022

Piezo-Electric Shear Rheometry: Further developments in experimental implementation and data extraction

The Piezo-electric Shear Gauge (PSG) [Christensen & Olsen, Rev. Sci. Instrum. 66, 5019, 1995] is a rheometric technique developed to measure the complex shear modulus of viscous liquids near their glass transition temperature. We report recent advances to the PSG technique: 1) The data extraction procedure is optimized which extends the upper limit of the frequency range of the method to between 50 and 70 kHz. 2) The measuring cell is simplified to use only one piezo-electric ceramic disc instead of three. We present an implementation of this design intended for liquid samples. Data obtained with this design revealed that a soft extra spacer is necessary to allow for thermal contraction of the sample in the axial direction. Model calculations show that flow in the radial direction is hindered by the confined geometry of the cell when the liquid becomes viscous upon cooling. The method is especially well-suited for -- but not limited to -- glassy materials.

cond-mat.soft↗

arXiv2016

Thermalization Calorimetry: A simple method for investigating glass transition and crystallization of supercooled liquids

We present a simple method for fast and cheap thermal analysis on supercooled glass-forming liquids. This "Thermalization Calorimetry" technique is based on monitoring the temperature and its rate of change during heating or cooling of a sample for which the thermal power input comes from heat conduction through an insulating material, i.e., is proportional to the temperature difference between sample and surroundings. The monitored signal reflects the sample's specific heat and is sensitive to exo- and endothermic processes. The technique is useful for studying supercooled liquids and their crystallization, e.g., for locating the glass transition and melting point(s), as well as for investigating the stability against crystallization and estimating the relative change in specific heat between the solid and liquid phases at the glass transition.

cond-mat.soft↗

arXiv2012

"Cooling by heating" - demonstrating the significance of the longitudinal specific heat

Heating a solid sphere at the surface induces mechanical stresses inside the sphere. If a finite amount of heat is supplied, the stresses gradually disappear as temperature becomes homogeneous throughout the sphere. We show that before this happens, there is a temporary lowering of pressure and density in the interior of the sphere, inducing a transient lowering of the temperature here. For ordinary solids this effect is small because c_p is almost equal to c_V. For fluent liquids the effect is negligible because their dynamic shear modulus vanishes. For a liquid at its glass transition, however, the effect is generally considerably larger than in solids. This paper presents analytical solutions of the relevant coupled thermoviscoelastic equations. In general, there is a difference between the isobaric specific heat, c_p, measured at constant isotropic pressure and the longitudinal specific heat, c_l, pertaining to mechanical boundary conditions that confine the associated expansion to be longitudinal. In the exact treatment of heat propagation the heat diffusion constant contains c_l rather than c_p. We show that the key parameter controlling the magnitude of the "cooling-by-heating" effect is the relative difference between these two specific heats. For a typical glass-forming liquid, when temperature at the surface is increased by 1 K, a lowering of the temperature in the sphere center of order 5 mK is expected if the experiment is performed at the glass transition. The cooling-by-heating effect is confirmed by measurements on a 19 mm diameter glucose sphere at the glass transition.

cond-mat.soft↗

arXiv2012

Identical temperature dependence of the time scales of several linear-response functions of two glass-forming liquids

The frequency-dependent dielectric constant, shear and adiabatic bulk moduli, longitudinal thermal expansion coefficient, and longitudinal specific heat have been measured for two van der Waals glass-forming liquids, tetramethyl-tetraphenyl-trisiloxane (DC704) and 5-polyphenyl-4-ether. Within the experimental uncertainties the loss-peak frequencies of the measured response functions have identical temperature dependence over a range of temperatures, for which the Maxwell relaxation time varies more than nine orders of magnitude. The time scales are ordered from fastest to slowest as follows: Shear modulus, adiabatic bulk modulus, dielectric constant, longitudinal thermal expansion coefficient, longitudinal specific heat. The ordering is discussed in light of the recent conjecture that van der Waals liquids are strongly correlating, i.e., approximate single-parameter liquids.

cond-mat.soft↗

arXiv2012

Measuring the dynamic thermal expansivity of molecular liquids near the glass transition

Based on previous works on polymers by Bauer et al. [Phys, Rev. B (2000)], this paper describes a capacitative method for measuring the dynamical expansion coefficient of a viscous liquid. Data are presented for the glass-forming liquid tetramethyl tetraphenyl trisiloxane (DC704) in the ultraviscous regime. Compared to the method of Bauer et al. the dynamical range has been extended by making time-domain experiments and by making very small and fast temperature steps. The modelling of the experiment presented in this paper includes the situation where the capacitor is not full because the liquid contracts when cooling from room temperature down to around the glass-transition temperature, which is relevant when measuring on a molecular liquid rather than polymer.

cond-mat.soft↗

arXiv2010

Beta relaxation in the shear mechanics of equilibrium viscous liquids: Phenomenology and network modeling of the alpha-beta merging region

The phenomenology of the beta relaxation process in the shear-mechanical response of glass-forming liquids is summarized and compared to that of the dielectric beta process. Furthermore, we discuss how to model the observations by means of standard viscoelastic modeling elements. Necessary physical requirements to such a model are outlined, and it is argued that physically relevant models must be additive in the shear compliance of the alpha and beta parts. A model based on these considerations is proposed and fitted to data for Polyisobutylene 680.

cond-mat.soft↗

arXiv2010

Frequency Dependent Specific Heat from Thermal Effusion in Spherical Geometry

We present a novel method of measuring the frequency dependent specific heat at the glass transition applied to 5-polyphenyl-4-ether. The method employs thermal waves effusing radially out from the surface of a spherical thermistor that acts as both a heat generator and thermometer. It is a merit of the method compared to planar effusion methods that the influence of the mechanical boundary conditions are analytically known. This implies that it is the longitudinal rather than the isobaric specific heat that is measured. As another merit the thermal conductivity and specific heat can be found independently. The method has highest sensitivity at a frequency where the thermal diffusion length is comparable to the radius of the heat generator. This limits in practise the frequency range to 2-3 decades. An account of the 3omega-technique used including higher order terms in the temperature dependency of the thermistor and in the power generated is furthermore given.

cond-mat.soft↗

arXiv2008

Supercooled Liquid Dynamics Studied via Shear-Mechanical Spectroscopy

We report dynamical shear-modulus measurements for five glass-forming liquids (pentaphenyl trimethyl trisiloxane, diethyl phthalate, dibutyl phthalate, 1,2-propanediol, and m-touluidine). The shear-mechanical spectra are obtained by the piezoelectric shear-modulus gauge (PSG) method. This technique allows one to measure the shear modulus ($10^{5} -10^{10}$ Pa) of the liquid within a frequency range from 1 mHz to 10 kHz. We analyze the frequency-dependent response functions to investigate whether time-temperature superposition (TTS) is obeyed. We also study the shear-modulus loss-peak position and its high-frequency part. It has been suggested that when TTS applies, the high-frequency side of the imaginary part of the dielectric response decreases like a power law of the frequency with an exponent -1/2. This conjecture is analyzed on the basis of the shear mechanical data. We find that TTS is obeyed for pentaphenyl trimethyl trisiloxane and in 1,2-propanediol while in the remaining liquids evidence of a mechanical $β$ process is found. Although the the high-frequency power law behavior $ω^{-α}$ of the shear-loss may approach a limiting value of $α=0.5$ when lowering the temperature, we find that the exponent lies systematically above this value (around 0.4). For the two liquids without beta relaxation (pentaphenyl trimethyl trisiloxane and 1,2-propanediol) we also test the shoving model prediction, according to which the the relaxation-time activation energy is proportional to the instantaneous shear modulus. We find that the data are well described by this model.

cond-mat.soft↗

arXiv2008

Investigation of the shear-mechanical and dielectric relaxation processes in two mono-alcohols close to the glass transition

Shear-mechanical and dielectric measurements on the two monohydroxy (mono-alcohol) molecular glass formers 2-ethyl-1-hexanol and 2-butanol close to the glass transition temperature are presented. The shear-mechanical data are obtained using the piezoelectric shear-modulus gauge method covering frequencies from 1mHz to 10kHz. The shear-mechanical relaxation spectra show two processes, which follow the typical scenario of a structural (alpha) relaxation and an additional (Johari-Goldstein) beta relaxation. The dielectric relaxation spectra are dominated by a Debye-type peak with an additional non-Debye peak visible. This Debye-type relaxation is a common feature peculiar to mono-alcohols. The time scale of the non-Debye dielectric relaxation process is shown to correspond to the mechanical structural (alpha) relaxation. Glass-transition temperatures and fragilities are reported based on the mechanical alpha relaxation and the dielectric Debye-type process, showing that the two glass-transition temperatures differ by approximately 10K and that the fragility based on the Debye-type process is a factor of two smaller than the structural fragility. If a mechanical signature of the Debye-type relaxation exists in these liquids, its relaxation strength is at most 1% and 3% of the full relaxation strength of 2-butanol and 2-ethyl-1-hexanol respectively. These findings support the notion that it is the non-Debye dielectric relaxation process that corresponds to the structural alpha relaxation in the liquid.

cond-mat.soft↗

arXiv2008

Solution of the spherically symmetric linear thermoviscoelastic problem in the inertia-free limit

The coupling between mechanical and thermal properties due to thermal expansion complicates the problem of measuring frequency-dependent thermoviscoelastic properties, in particular for highly viscous liquids. A simplification arises if there is spherical symmetry where - as detailed in the present paper - the thermoviscoelastic problem may be solved analytically in the inertia-free limit, i.e., the limit where the sample is much smaller than the wavelength of sound waves at the frequencies of interest. As for the one-dimensional thermoviscoelastic problem [Christensen et al., Phys. Rev. E 75, 041502 (2007)], the solution is conveniently formulated in terms of the so-called transfer matrix, which directly links to the boundary conditions that can be experimentally controlled. Once the transfer matrix has been calculated, it is fairly easy to deduce the equations describing various experimentally relevant special cases (boundary conditions that are adiabatic, isothermal, isochoric, etc.). In most situations the relevant frequency-dependent specific heat is the longitudinal specific heat, a quantity that is in between the isochoric and isobaric frequency-dependent specific heats.

cond-mat.soft↗

arXiv2007

Approximate square-root-time relaxation in glass-forming liquids

We present data for the dielectric relaxation of 43 glass-forming organic liquids, showing that the primary (alpha) relaxation is often close to square-root-time relaxation. The better an inverse power-law description of the high-frequency loss applies, the more accurately is square-root-time relaxation obeyed. These findings suggest that square-root-time relaxation is generic to the alpha process, once a common view, but since long believed to be incorrect. Only liquids with very large dielectric losses deviate from this picture by having consistently narrower loss peaks. As a further challenge to the prevailing opinion, we find that liquids with accurate square-root-time relaxation cover a wide range of fragilities.

cond-mat.soft↗

arXiv2007

Glass-forming liquids: One or more "order" parameters?

We first summarize the classical arguments that the vast majority of glass-forming liquids require more than one "order" parameter for their description. Critiques against this conventional wisdom are then presented, and it is argued that the matter deserves to be reconsidered in light of recent experimental developments. Out of the eight basic thermoviscoelastic frequency-dependent response functions, there are generally three independent functions. For stochastic dynamics we show that there are only two independent response functions; for this case it is shown how analytic continuation may be utilized to express the third response functions in terms of two others. Operational criteria are presented for the linear thermoviscoelasticity being described by a single "order" parameter, in which case there is just one independent thermoviscoelastic response function. It is shown that a single "order" parameter description applies to a good approximation whenever thermal equilibrium fluctuations of fundamental variables like energy and pressure are strongly correlated. Results from computer simulations showing that this is the case for a number of simple glass-forming liquids, as well as a few exceptions, are briefly presented. Finally, we discuss a new conjecture according to which experiments at varying temperature and pressure follow the density-scaling expression for the relaxation time, $τ=F(ρ^x/T)$ ($ρ$ and $T$ are density and temperature), if and only if the liquid is "strongly correlating," i.e., to a good approximation is described by a single "order" parameter.

cond-mat.soft↗

arXiv2007

Feasibility of single-order parameter description of equilibrium viscous liquid dynamics

Molecular dynamics results for the dynamic Prigogine-Defay ratio are presented for two glass-forming liquids, thus evaluating the experimentally relevant quantity for testing whether metastable-equilibrium liquid dynamics to a good approximation are described by a single parameter. For the Kob-Andersen binary Lennard-Jones mixture as well as for an asymmetric dumbbell model liquid a single-parameter description works quite well. This is confirmed by time-domain results where it is found that energy and pressure fluctuations are strongly correlated on the alpha-time scale in the NVT ensemble; in the NpT ensemble energy and volume fluctuations similarly correlate strongly.

cond-mat.soft↗

arXiv2007

Can the frequency-dependent specific heat be measured by thermal effusion methods?

It has recently been shown that plane-plate heat effusion methods devised for wide-frequency specific-heat spectroscopy do not give the isobaric specific heat, but rather the so-called longitudinal specific heat. Here it is shown that heat effusion in a spherical symmetric geometry also involves the longitudinal specific heat.

cond-mat.soft↗

arXiv2007

Conventional methods fail to measure c_p(omega) of glass-forming liquids

The specific heat is frequency dependent in highly viscous liquids. By solving the full one-dimensional thermo-viscoelastic problem analytically it is shown that, because of thermal expansion and the fact that mechanical stresses relax on the same time scale as the enthalpy relaxes, the plane thermal-wave method does not measure the isobaric frequency-dependent specific heat c_p(omega). This method rather measures a "longitudinal" frequency-dependent specific heat, a quantity defined and detailed here that is in-between c_p(omega) and c_v(omega). This result means that no wide-frequency measurements of c_p(omega) on liquids approaching the calorimetric glass transition exist. We briefly discuss consequences for experiment.

cond-mat.soft↗

arXiv2006

Elastic models for the non-Arrhenius viscosity of glass-forming liquids

This paper first reviews the shoving model for the non-Arrhenius viscosity of viscous liquids. According to this model the main contribution to the activation energy of a flow event is the energy needed for molecules to shove aside the surrounding, an energy which is proportional to the instantaneous shear modulus of the liquid. Data are presented supporting the model. It is shown that the fractional Debye-Stokes-Einstein relation, that quantitatively expresses the frequently observed decoupling of, e.g., conductivity from viscous flow, may be understood within the model. The paper goes on to review several related explanations for the non-Arrhenius viscosity. Most of these are also "elastic models," i.e., they express the viscosity activation energy in terms of short-time elastic properties of the liquid. Finally, two new arguments for elastic models are given, a general solid-state defect argument and an Occam's razor type argument.

cond-mat.soft↗

arXiv2004

A single-frequency test for one-parameter models of the linear thermo-visco-elastic response of glass-forming liquids

A master equation description of the inherent dynamics is used to calculate the frequency-dependent linear thermo-visco-elastic response functions of a glass-forming liquid. From the imaginary parts of the isobaric specific heat, isothermal bulk modulus, and isobaric thermal expansion coefficient, we define a quantity $Λ_{Tp}(ω)$ with the property that $Λ_{Tp}(ω)=1$ is equivalent to having a one-parameter description of the linear thermo-visco-elastic response. This provides an alternative to the well-known criterion based on the Prigogine-Defay ratio.

cond-mat.stat-mech↗

arXiv2001

Testing models for structural relaxation of viscous liquids by temperature jump experiments

Based on the Tool-Narayanaswami formalism for structural relaxation we propose an experiment which independent of the relaxation time distribution determines the structural relaxation rate by subtracting relaxations following two different temperature jumps. In particular, the experiment makes it possible to evaluate the relaxation rate immediately following a temperature jump - thus allowing one to distinguish the entropy model from others.

cond-mat.soft↗