arXiv subjects

Tai Oshima

Publications and source records attributed to Tai Oshima.

At least 19 recordsLinked to original sources

arXiv2026

FINER: development of the wideband millimeter-wave receiver system and preparations for first light on the Large Millimeter Telescope

The recent discovery of an excess of luminous galaxies in the early Universe necessitates sensitive and wideband millimeter spectroscopy to understand their rapid growth. To address this, we present the development of the Far-Infrared Nebular Emission Receiver (FINER) for the Large Millimeter Telescope (LMT). The FINER frontend comprises two receivers covering 120-350 GHz (corresponding to ALMA Bands 4+5 and 6+7). The warm optics are designed to enable simultaneous two-band observations. Combined with the 10.24-GHz-wide digital spectrometer array, the system aims to deliver an instantaneous bandwidth approximately five times wider than current ALMA capabilities. We report that the 210-350 GHz receiver has already achieved commissioning-level performance, with sideband rejection further enhanced by the digital sideband separation technique. With installation expected in 2026, we discuss parallel preparations, including integrated testing and commissioning plans for first-look targets.

astro-ph.IM↗

arXiv2026

GLTCAM: Concept of Multi-color Millimeter and Submillimeter Camera for the Greenland Telescope

To investigate the formation history of large-scale structure through the dynamics of galaxy clusters, we are developing a multi-color millimeter and submillimeter-wave continuum camera (GLTCAM) for deployment on the Green-land Telescope (GLT). GLTCAM will observe in six frequency bands - three in the millimeter range (150, 220, and 270 GHz) and three in the submillimeter range (350, 400, and 670 GHz). The optical design provides a compact configuration that fits within the GLT receiver cabin, while delivering diffraction-limited performance over an $18'$ field of view with minimal telecentricity error and distortion. A key advantage of this design is its uniform illumination footprint at the cold stop, which helps minimize thermal loading on both the detectors and the cryogenic stages. The focal plane module comprises a quasi-optical bandpass filter, a conical horn array coupled with planar ortho mode transducers (OMTs), and a superconducting multi-color microwave kinetic inductance detector (MKID) array. Current development efforts are focused on the three-color millimeter-wave module. The detector array employs a single-layer coplanar waveguide (CPW) architecture, which simplifies fabrication and enables scalability to large-format arrays. GLTCAM aims for the early realization of next-generation wide-field, multi-color observations as a pathfinder for future large submillimeter telescopes.

astro-ph.IM↗

arXiv2026

Design Method of Quasi-Lumped Element Bandpass Filters Using Superconducting Coplanar Waveguide for Millimeter-Wave Multichroic Imaging

An on-chip band-defining filter coupled with a superconducting photon detector is a promising technology for developing multi-band imaging cameras at millimeter and submillimeter wavelengths. In this paper, we present the design of on-chip bandpass filters based on coplanar waveguide geometry, which can be easily integrated into large-format multi-band detector arrays. A lumped element filter design is suitable not only for achieving a compact footprint but also for suppressing harmonics to reduce band-to-band crosstalk in a multiplexer. However, the coplanar waveguide geometry and the photolithography process rule limit the maximum available inductance and capacitance of lumped elements, which does not sufficiently meet the requirements of filter circuits. To overcome this limitation, we have established a design method for quasi-lumped element filters, in which the maximum element size is relaxed to a quarter wavelength, exceeding the ideal lumped element size. We achieved design solutions for 150, 220, and 270 GHz 8th-order Chebyshev bandpass filters and a triplexer. We also report on the measurement results of a scaled model of the bandpass filter, demonstrating the validity of our proposed filter design.

astro-ph.IM↗

arXiv2026

Broadband anti-reflection coating for sub-terahertz optics using dielectric multilayers

Sub-terahertz astronomy requires instruments capable of simultaneous observations across multiple spectral bands, motivating the development of broadband anti-reflection coatings (ARCs). We investigated low-loss dielectrics with refractive indices suitable for multilayer ARCs on polyethylene optical elements and identified candidates that partially meet the requirements. To address the remaining gaps in available refractive indices, we applied dielectric multilayer synthesis by combining newly identified thin materials with controlled bonding to realize the required effective refractive indices. As a result, the fabricated 5-layer ARC achieved reflection losses of 0.2% (average) and 3.2% (maximum) over 130-710 GHz.

astro-ph.IM↗

arXiv2026

A Wideband Millimeter-wave Receiver at 210-350 GHz for LMT-FINER

The Far-Infrared Nebular Emission Receiver (FINER) project is developing two wideband dual-polarization sideband-separating receivers covering 120-210 GHz and 210-350 GHz to efficiently identify high-redshift galaxy candidates in the early universe. Based on high-critical-current-density superconductor-insulator-superconductor mixer technology originally developed for the ALMA wideband sensitivity upgrade, the FINER receivers are designed to provide an intermediate-frequency bandwidth of 3-21 GHz per sideband and per polarization, approximately five times wider than the current ALMA specifications. After installation on the Large Millimeter Telescope, these receivers are expected to offer highly efficient spectral-scanning capability among (sub)millimeterwave facilities in the northern-hemisphere. This paper reports the initial laboratory characterization of the 210-350 GHz receiver. The measured single sideband receiver noise temperature is approximately 100 K over most of the radio-frequency band. Digital sideband separation was also demonstrated using a wideband spectrometer array (DRS4), achieving an image rejection ratio of around 20 dB in the initial tests. These results represent an important step toward the realization of a wideband spectral-scanning receiver system for FINER.

astro-ph.IM↗

arXiv2025

The LMT 2 millimeter receiver system (B4R). II. Science demonstration observations toward Orion-KL/OMC-1

We present the results of mapping and single-point spectral scans toward Orion-KL/OMC-1 performed as science demonstrations of a 2 mm SIS receiver, the Band 4 Receiver (B4R), installed on the 50 m Large Millimeter Telescope (LMT). To prove the capabilities of mapping and spectral scans with the B4R on the LMT, commissioning observations were conducted employing the on-the-fly mapping technique toward Orion-KL/OMC-1, which covers a map size of 5$'\times$5$'$. These mapping observations were performed with two frequency settings providing 10 GHz in total (131.4-133.9 GHz and 145.1-147.6 GHz; 136.2-138.7 GHz and 149.9-152.4 GHz) with a frequency resolution of 76.293 kHz. We conducted spectral line identification analysis for the hot core and compact ridge regions in the Orion-KL with a beam size of 11-12$''$. We detected nearly 400 emission lines and identified two recombination lines and 29 molecular species, including isotopologues, deuterated molecules, and vibrational excited states, despite the short integration time. These results are consistent with those of previous studies. The 29 molecular species include nitrogen (N)-bearing complex organic molecules (COMs) and oxygen (O)-bearing COMs. To demonstrate the capability of the B4R in astrochemistry, we conducted detailed analyses of column densities, rotational temperatures, and relative abundances with respect to H$_2$ on two representative COMs, N-bearing C$_2$H$_5$CN and O-bearing CH$_3$OCHO in the central 40$''\times$40$''$ area of the map. The wide bandwidth of 10 GHz enabled the use of 8 and 34 emission lines, respectively. The spatial differences in the physical and chemical properties between these molecules were derived at a spatial resolution of $\sim$12$''$. The B4R on the LMT was successfully demonstrated to be powerful for mapping and spectral scans and to have high potential for the study of interstellar chemistry.

astro-ph.GA↗

arXiv2025

The LMT 2 Millimeter Receiver System (B4R). I. Overview and Results of Science Demonstration

We report on the results of the on-sky test and science demonstration conducted with the 2 mm receiver system, B4R, on the 50 m Large Millimeter Telescope (LMT), located at an altitude of 4600 m in Mexico. The B4R receiver was developed based on the dual-polarization sideband-separating mixer technology of the Atacama Large Millimeter/submillimeter Array, and is equipped with a fast Fourier transform digital spectrometer, XFFTS. The primary science objective is the spectroscopic redshift identification of high-redshift dusty star-forming galaxies, complementing the existing 3 mm Redshift Search Receiver by enabling the detection of multiple carbon monoxide lines. Additionally, the B4R receiver broadens the range of science cases possible with the LMT, including astrochemistry, as the 2 mm band encompasses unique molecular lines such as deuterated molecules and shock tracers. During on-site commissioning in 2018 and 2019, we successfully demonstrated on-the-fly mapping and position-switching observations toward the Orion Molecular Cloud 1 and bright high-redshift dusty star-forming galaxies, respectively. We confirmed that the installed B4R system largely met its basic performance specifications. Furthermore, we measured the LMT's aperture efficiencies across the entire B4R frequency range (130-160 GHz), finding them to be roughly consistent with expectations based on a surface accuracy of 100 $\mu$m and the receiver optics design. These results with the B4R will enable the most sensitive single-dish spectroscopic observations at 2 mm using the LMT.

astro-ph.IM↗

arXiv2024

FINER: Far-Infrared Nebular Emission Receiver for the Large Millimeter Telescope

Unveiling the emergence and prevalence of massive/bright galaxies during the epoch of reionization and beyond, within the first 600 million years of the Universe, stands as a pivotal pursuit in astronomy. Remarkable progress has been made by JWST in identifying an immense population of bright galaxies, which hints at exceptionally efficient galaxy assembly processes. However, the underlying physical mechanisms propelling their rapid growth remain unclear. With this in mind, millimeter and submillimeter-wave spectroscopic observations of redshifted far-infrared spectral lines, particularly the [O III] 88 micron and [C II] 158 micron lines, offers a crucial pathway to address this fundamental query. To this end, we develop a dual-polarization sideband-separating superconductor-insulator-superconductor (SIS) mixer receiver, FINER, for the Large Millimeter Telescope (LMT) situated in Mexico. Harnessing advancements from ALMA's wideband sensitivity upgrade (WSU) technology, FINER covers radio frequencies spanning 120-360 GHz, delivering an instantaneous intermediate frequency (IF) of 3-21 GHz per sideband per polarization, which is followed by a set of 10.24 GHz-wide digital spectrometers. At 40% of ALMA's light-collecting area, the LMT's similar atmospheric transmittance and FINER's 5 times wider bandwidth compared to ALMA culminate in an unparalleled spectral scanning capability in the northern hemisphere, paving the way for finer spectral-resolution detection of distant galaxies.

astro-ph.IM↗

arXiv2024

A Design Method of an Ultra-Wideband and Easy-to-Array Magic-T: A 6-14 GHz Scaled Model for a mm/submm Camera

We established a design method for a Magic-T with a single-layer dielectric/metal structure suitable for both wideband and multi-element applications for millimeter and submillimeter wave imaging observations. The design method was applied to a Magic-T with a coupled-line, stubs, and single-stage impedance transformers in a frequency-scaled model (6-14 GHz) that is relatively easy to demonstrate through manufacturing and evaluation. The major problem is that using the conventional perfect matching condition for a coupled-line alone produces an impractically large width coplanar coupled-line (CPCL) to satisfy the desired bandwidth ratio. In our study, by removing this constraint and optimizing impedances utilizing a circuit simulator with high computation speed, we found a solution with a $\sim$ 180 $\rm \mu$m wide CPCL, which is approximately an order of magnitude smaller than the conventional analytical solution. Furthermore, considering the effect of transition discontinuities in the transmission lines, we optimized the line length and obtained a design solution with return loss < -20 dB, amplitude imbalance < 0.1 dB, and phase imbalance < 0.5$^\circ$ from 6.1 GHz to 14.1 GHz.

astro-ph.IM↗

arXiv2024

Large-Scale Mapping Observations of DCN and DCO$^+$ toward Orion KL

We present emission maps (1.5'$\times$1.5' scale, corresponding to 0.18 pc) of the DCN ($J=2-1$) and DCO$^+$ ($J=2-1$) lines in the 2 mm band toward the Orion KL region obtained with the 2 mm receiver system named B4R installed on the Large Millimeter Telescope (LMT). The DCN emission shows a peak at the Orion KL hot core position, whereas no DCO$^+$ emission has been detected there. The DCO$^+$ emission shows enhancement at the west side of the hot core, which is well shielded from the UV radiation from OB massive stars in the Trapezium cluster. We have derived the abundance ratio of DCN/DCO$^+$ at three representative positions where both species have been detected. The gas components with $V_{\rm {LSR}} \approx 7.5-8.7$ km/s are associated with low abundance ratios of $\sim4-6$, whereas much higher abundance ratios ($\sim22-30$) are derived for the gas components with $V_{\rm {LSR}} \approx 9.2-11.6$ km/s. We have compared the observed abundance ratio to our chemical models and found that the observed differences in the DCN/DCO$^+$ abundance ratios are explained by different densities.

astro-ph.GA↗

arXiv2022

Material properties of a low contraction and resistivity silicon-aluminum composite for cryogenic detectors

We report on the cryogenic properties of a low-contraction silicon-aluminum composite, namely Japan Fine Ceramics SA001, to use as a packaging structure for cryogenic silicon devices. SA001 is a silicon--aluminum composite material (75% silicon by volume) and has a low thermal expansion coefficient ($\sim$1/3 that of aluminum). The superconducting transition temperature of SA001 is measured to be 1.18 K, which is in agreement with that of pure aluminum, and is thus available as a superconducting magnetic shield material. The residual resistivity of SA001 is 0.065 $\mathrm{\mu \Omega m}$, which is considerably lower than an equivalent silicon--aluminum composite material. The measured thermal contraction of SA001 immersed in liquid nitrogen is $\frac{L_{293\mathrm{K}}-L_{77\mathrm{K}}}{L_{293\mathrm{K}}}=0.12$%, which is consistent with the expected rate obtained from the volume-weighted mean of the contractions of silicon and aluminum. The machinability of SA001 is also confirmed with a demonstrated fabrication of a conical feedhorn array, with a wall thickness of 100 $\mathrm{\mu m}$. These properties are suitable for packaging applications for large-format superconducting detector devices.

astro-ph.IM↗

arXiv2021

DESHIMA 2.0: development of an integrated superconducting spectrometer for science-grade astronomical observations

Integrated superconducting spectrometer (ISS) technology will enable ultra-wideband, integral-field spectroscopy for (sub)millimeter-wave astronomy, in particular, for uncovering the dust-obscured cosmic star formation and galaxy evolution over cosmic time. Here we present the development of DESHIMA 2.0, an ISS for ultra-wideband spectroscopy toward high-redshift galaxies. DESHIMA 2.0 is designed to observe the 220-440 GHz band in a single shot, corresponding to a redshift range of $z$=3.3-7.6 for the ionized carbon emission ([C II] 158 $\mu$m). The first-light experiment of DESHIMA 1.0, using the 332-377 GHz band, has shown an excellent agreement among the on-sky measurements, the lab measurements, and the design. As a successor to DESHIMA 1.0, we plan the commissioning and the scientific observation campaign of DESHIMA 2.0 on the ASTE 10-m telescope in 2023. Ongoing upgrades for the full octave-bandwidth system include the wideband 347-channel chip design and the wideband quasi-optical system. For efficient measurements, we also develop the observation strategy using the mechanical fast sky-position chopper and the sky-noise removal technique based on a novel data-scientific approach. In the paper, we show the recent status of the upgrades and the plans for the scientific observation campaign.

astro-ph.IM↗

arXiv2021

Wavefront sensor for millimeter/submillimeter-wave adaptive optics based on aperture-plane interferometry

We present a concept of a millimeter wavefront sensor that allows real-time sensing of the surface of a ground-based millimeter/submillimeter telescope. It is becoming important for ground-based millimeter/submillimeter astronomy to make telescopes larger with keeping their surface accurate. To establish `millimetric adaptive optics (MAO)' that instantaneously corrects the wavefront degradation induced by deformation of telescope optics, our wavefront sensor based on radio interferometry measures changes in excess path lengths from characteristic positions on the primary mirror surface to the focal plane. This plays a fundamental role in planned 50-m class submillimeter telescopes such as LST and AtLAST.

astro-ph.IM↗

arXiv2020

Demonstration of wideband metal mesh filters for submillimeter astrophysics using flexible printed circuits

We developed a wideband quasi-optical band-pass filter covering 170-520 GHz by exploiting the recent advancements in commercially available flexible printed circuit (FPC) fabrication technologies. We designed and fabricated a three-layered stack of loaded hexagonal grid metal meshes using a copper pattern with a narrowest linewidth of $50~μ\mathrm{m}$ on a polyimide substrate. The measured frequency pass-band shape was successfully reproduced through a numerical simulation using a set of parameters consistent with the dimensions of the fabricated metal meshes. FPC-based metal mesh filters will provide a new pathway toward the on-demand development of millimeter/submillimeter-wave quasi-optical filters at low cost and with a short turnaround time.

astro-ph.IM↗

arXiv2020

DESHIMA on ASTE: On-sky Responsivity Calibration of the Integrated Superconducting Spectrometer

We are developing an ultra-wideband spectroscopic instrument, DESHIMA (DEep Spectroscopic HIgh-redshift MApper), based on the technologies of an on-chip filter-bank and Microwave Kinetic Inductance Detector (MKID) to investigate dusty star-burst galaxies in the distant universe at millimeter and submillimeter wavelength. An on-site experiment of DESHIMA was performed using the ASTE 10-m telescope. We established a responsivity model that converts frequency responses of the MKIDs to line-of-sight brightness temperature. We estimated two parameters of the responsivity model using a set of skydip data taken under various precipitable water vapor (PWV, 0.4-3.0 mm) conditions for each MKID. The line-of-sight brightness temperature of sky is estimated using an atmospheric transmission model and the PWVs. As a result, we obtain an average temperature calibration uncertainty of $1σ=4$%, which is smaller than other photometric biases. In addition, the average forward efficiency of 0.88 in our responsivity model is consistent with the value expected from the geometrical support structure of the telescope. We also estimate line-of-sight PWVs of each skydip observation using the frequency response of MKIDs, and confirm the consistency with PWVs reported by the Atacama Large Millimeter/submillimeter Array.

astro-ph.IM↗

arXiv2019

First light demonstration of the integrated superconducting spectrometer

Ultra-wideband 3D imaging spectrometry in the millimeter-submillimeter (mm-submm) band is an essential tool for uncovering the dust-enshrouded portion of the cosmic history of star formation and galaxy evolution. However, it is challenging to scale up conventional coherent heterodyne receivers or free-space diffraction techniques to sufficient bandwidths ($\geq$1 octave) and numbers of spatial pixels (>$10^2$). Here we present the design and first astronomical spectra of an intrinsically scalable, integrated superconducting spectrometer, which covers 332-377 GHz with a spectral resolution of $F/ΔF \sim 380$. It combines the multiplexing advantage of microwave kinetic inductance detectors (MKIDs) with planar superconducting filters for dispersing the signal in a single, small superconducting integrated circuit. We demonstrate the two key applications for an instrument of this type: as an efficient redshift machine, and as a fast multi-line spectral mapper of extended areas. The line detection sensitivity is in excellent agreement with the instrument design and laboratory performance, reaching the atmospheric foreground photon noise limit on sky. The design can be scaled to bandwidths in excess of an octave, spectral resolution up to a few thousand and frequencies up to $\sim$1.1 THz. The miniature chip footprint of a few $\mathrm{cm^2}$ allows for compact multi-pixel spectral imagers, which would enable spectroscopic direct imaging and large volume spectroscopic surveys that are several orders of magnitude faster than what is currently possible.

astro-ph.IM↗

arXiv2019

Astro2020 Science White Paper: Exploration and characterization of the earliest epoch of galaxy formation: beyond the re-ionization era

State-of-the-art rest-frame UV and FIR photometric and spectroscopic observations are now pushing the redshift frontiers of galaxy formation studies up to $z\sim9-11$ and beyond. Recent HST observations unveiled the presence of a star-forming galaxy exhibiting the Lyman break at $λ_{\rm obs}=1.47\pm0.01$ $μ$m, i.e., a $z=11.09^{+0.08}_{-0.12}$ galaxy with a stellar mass of $\sim10^9 M_\odot$, demonstrating that galaxy build-up was well underway early in the epoch of reionization (EoR) at $z>10$. Targeted spectroscopy of a lensed Lyman break galaxy uncovers the earliest metals known to date up to $z=9.1096\pm0.0006$ by detecting the bright [OIII] 88~$μ$m nebular line, indicating the onset of star formation 250 million years after the Big Bang, i.e., corresponding to a redshift of $z\sim15$. These latest findings lead us to a number of key questions: How and when metal enrichment happened in the EoR? What was the nature of the earliest-epoch star-forming galaxies at $z=10-15$? What was the spatial distribution of such galaxies, and what was the relation to the putative large-scale ionization bubbles during the EoR? What were the dark-halo masses of such earliest-epoch star-forming galaxies? To address all these questions, we need to uncover a statistically large number of $z=10-15$ galaxies in the pre-reionization era. Here we argue two possible pathways: (1) a wide-area, sensitive blind spectroscopic survey of [OIII] 88 $μ$m line-emitting galaxies at submillimeter wavelengths, and (2) an ultra-wide-area, high-cadence photometric survey of transient sources at radio-to-(sub)millimeter wavelengths, together with the immediate follow-up spectroscopy with an ultra-wide-band spectrograph, to catch the pop-III $γ$-ray bursts.

astro-ph.GA↗

arXiv2018

The Dust-Selected Molecular Clouds in the Northeast Region of the Small Magellanic Cloud

We present a high-sensitivity ($1σ<1.6~\mathrm{mJy~beam^{-1}}$) continuum observation in a 343 arcmin$^2$ area of the northeast region in the Small Magellanic Cloud at a wavelength of 1.1 mm, conducted using the AzTEC instrument on the ASTE telescope. In the observed region, we identified 20 objects by contouring $10σ$ emission. Through spectral energy distribution (SED) analysis using 1.1 mm, $Herschel$, and $Spitzer$ data, we estimated the gas masses of $5\times 10^3-7\times 10^4~\mathrm{M_\odot}$, assuming a gas-to-dust ratio of 1000. Dust temperature and the index of emissivity were also estimated as $18-33$ K and $0.9-1.9$, respectively, which are consistent with previous low resolution studies. The relation between dust temperature and the index of emissivity shows a weak negative linear correlation. We also investigated five CO-detected dust-selected clouds in detail. The total gas masses were comparable to those estimated from the Mopra CO data, indicating that the assumed gas-to-dust ratio of 1000 and the $X_\mathrm{CO}$ factor of $1\times10^{21}~\mathrm{cm^{-2}~(K~km~s^{-1})^{-1}}$, with uncertainties of a factor of 2, are reliable for the estimation of the gas masses of molecular or dust-selected clouds. Dust column density showed good spatial correlation with CO emission, except for an object that associates with bright young stellar objects. The $8~\mathrm{μm}$ filamentary and clumpy structures also showed similar spatial distribution with the CO emission and dust column density, supporting the fact that polycyclic aromatic hydrocarbon emissions arise from the surfaces of dense gas and dust clouds.

astro-ph.GA↗