Searcharxiv⌕ Search

arXiv subjects

Tayyab Imran

Publications and source records attributed to Tayyab Imran.

6 recordsLinked to original sources
arXiv2021

Design Simulation of Czerny-Turner Configuration-based Raman Spectrometer using physical optics propagation algorithm

We report the design simulation of the Raman spectrometer using optical system design software Zemax. The design is based on the Czerny-turner configuration which includes an optical system consisting of an entrance slit, two concave mirrors, reflecting type diffraction grating, and an image detector. The system's modelling approach is suggested by introducing the corresponding relationship between detector pixels and wavelength, linear CCD receiving surface length, and image surface dimension. Simulations have been carried out using the POP (Physical Optics Propagation) algorithm. Spot diagram, relative illumination, irradiance plot, Modulation Transfer Function (MTF), geometric, and encircled energy simulated for designing the Raman spectrometer. The simulation results of the Raman spectrometer's using a 527 nm wavelength laser as an excitation light source are presented. The present optical system is designed in sequential mode and a Raman spectrum observed in the range of 530 to 630 nm. The analysis shows that the system's image efficiency is higher, predicting that it is possible to build an efficient and cost-effective Raman spectrometer for optical diagnostics.

physics.optics↗
arXiv2021

Non-linear propagation effects of intense femtosecond pulses on low order harmonics in solids

The non-linear propagation of the intense near-infrared (NIR) driving field in wide bandgap materials pose a challenge and an opportunity to control the spectral properties of high harmonic generation (HHG) in solids. Here, we have investigated the non-linear propagation effects of the ultrafast intense near-infrared (NIR) driving field at 800 nm of 40 fs pulse duration operating at a repetition rate of 1 kHz focused on the wide bandgap dielectrics such as MgO, Chromium (Cr) doped MgO (Cr: MgO), Sapphire (Sa) crystals and fused silica (FS). Furthermore, we have generated second and third harmonic (TH) in these materials to explore the non-linear response at a strong field. To quantify the non-linear propagation effects, low-order harmonics have been generated in reflection and compared with the harmonics generated in transmission. We observe spectral shifts and broadening of the driving field spectrum which is imprinted on the harmonics. We attribute these effects to strong photoionization, generation of free-carrier density and self-phase modulation effects. We have also studied the polarization dependence of second harmonic generation (SHG) and TH in FS. The linear polarization dependence of below bandgap harmonics in FS and Sa generated in reflection demonstrated the sharp anisotropy than in transmission. This work shows the sensitivity to control the spectral profile of harmonics by manipulating the driving field, showing the possibility of new tailored solid-state XUV sources for optical diagnostics.

physics.optics↗
arXiv2020

Controlling the nonlinear optical properties of MgO by tailoring the electronic structure

The study of the non-linear response of matter to high electric fields has recently encompassed harmonic generation in solids at near-infrared (NIR) driving wavelengths. Interest has been driven by the prospect of ultrafast signal processing and all-optical mapping of electron wave-functions in solids. Engineering solid-state band structures to control the non-linear process has already been highlighted theoretically. Here, we show experimentally for the first time that second harmonic generation (SHG) can be enhanced by doping crystals of magnesium oxide (MgO) with chromium (Cr) atoms. We show that the degree of enhancement depends non-linearly on dopant concentration. The SHG efficiency is shown to increase when Cr dopants are introduced into pure MgO. A physical picture of the effect of Cr dopants is aided by density functional theory (DFT) calculations of the electronic structure for pure and doped samples. This work shows an unambiguous enhancement of the SHG efficiency by modifying the electronic structure. The observed effects are consistent with an electronic structure that facilitates the surface induced SHG and demonstrates a minimal angular dependence. This work highlights the potential of manipulating the electronic structure of solids to control or test theories of their non-linear optical response.

physics.optics↗
arXiv2019

Thermal lensing measurements of Ti: Sapphire crystal pumped at 80 MHz picosecond pulses by Shack-Hartmann wavefront sensor

The thermal lensing effects in the lasing crystal appear to be dominant when the pump laser focused on the lasing crystal which causes the local heating effect. The spatial refractive index variations observed if the crystal has non-uniform temperature distribution. In the present study, the demonstration of thermal lensing effect of Brewster-cut Ti: Sapphire crystal carried out when pumped by 25 ps pulses at 80 MHz repetition rate with 532 nm central wavelength, while the average pump power controlled by the attenuator. The thermal lensing effects measured first at the ~293 K temperature and later at ~40 K by using the cryogenic cooling system. The thermal lensing variations at different average pump power were calculated and measured by using the HASO4 Shack-Hartmann wavefront sensor.

physics.optics↗
arXiv2018

Design and characterization simulation of Ti: sapphire-based femtosecond laser system using Lab2 tools in the NI LabView

We report on the 825-nm center wavelength, 9.17 mJ pulse energy Ti:sapphire-based femtosecond laser system simulation carried out by Lab2 tools in LabVIEW (National Instruments, Inc.). The design investigation and characterization of stretched, amplified and compressed pulses made by intensity module and second harmonic generation (SHG) frequency-resolved optical gating (FROG) module in Lab2. The minimum pulse duration of ~37.80 fs at the output of the compressor end obtained by simulations. The variation of pulse energy, FWHM and central wavelength versus number of passes in the amplifier are computed. The lab2 tools help to design and characterize laser system before to set up on the optical table. The simulation results save time to calculate parameters which are essential in femtosecond laser system designing. The Lab2 simulation tools, along with financial constraints, it is easier, simple and efficient to obtain results in short time.

physics.ins-det↗