arXiv subjects

Thomas Corbitt

Publications and source records attributed to Thomas Corbitt.

At least 19 recordsLinked to original sources

arXiv2025

Thermal Noise Measurement Below the Standard Quantum Limit

We present a method characterizing thermal noise in an optical cavity independent from quantum noise despite the thermal noise falling below the quantum noise limit. Using this method, we measured the thermal noise contribution from a GaAs AlGaAs micro-mirror suspended on a GaAs cantilever microresonator when brought to a cryogenic temperature (approximately 25 K) and incorporated into a Fabry Perot cavity. An optical spring is formed in this optical cavity. Previously, this setup exploited an optical spring to produce a displacement sensitivity falling 2.8 dB below the free-mass standard quantum limit (SQL), as reported by Cullen et. al. Here we use a similar setup to measure thermal noise which fell a maximum of 5 dB below the SQL. This measurement, in turn, allowed for an investigation of quantum noise suppression resulting from the optical spring effect, falling a maximum of 10 dB below the SQL.

quant-ph↗

arXiv2024

Optical Spring Tracking for Enhancing Quantum-Limited Interferometers

Modern interferometers such as LIGO have achieved sensitivities limited by quantum noise, comprised of radiation pressure and shot noise. To mitigate this noise, a static system is employed that minimizes the quantum noise within the measurement band. However, since gravitational wave inspiral signals are a single frequency changing over time, only noise at the chirp frequency needs to be minimized. Here we demonstrate dynamically tracking a target signal using an optical spring, resulting in an increased signal to noise ratio (SNR). We report on a SNR increase by up to a factor of 40 when compared to a static configuration.

quant-ph↗

arXiv2022

Surpassing the Standard Quantum Limit using an Optical Spring

Quantum mechanics places noise limits and sensitivity restrictions on physical measurements. The balance between unwanted backaction and the precision of optical measurements impose a standard quantum limit (SQL) on interferometric systems. In order to realize a sensitivity below the SQL, it is necessary to leverage a back-action evading measurement technique, or else exploit cancellations of any excess noise contributions at the detector. %Many proof of principle experiments have been performed, but only recently has an experiment achieved sensitivity below the SQL. In this work, we extend that initial demonstration and realize sub-SQL measurement sensitivity nearly two times better than previous measurements, and with architecture applicable to interferometric gravitational wave detectors. In fact, this technique is directly applicable to Advanced LIGO, which could observe similar effects with a detuned signal recycling cavity. By exploiting quantum correlations created by an optical spring, we measure a total sensitivity below the SQL by $\textbf{2.8}$ dB, corresponding to a reduction in the noise power by $\textbf{72}\pm\textbf{5.1}$ \% below the quantum limit. Through the use of a detuned optical spring, this noise reduction is tunable, allowing us to choose the desired range of frequencies that fall below the SQL. This result demonstrates access to sensitivities well below the SQL at frequencies ranges applicable to LIGO, with the potential to extend the reach of gravitational wave detectors further into the universe.

quant-ph↗

arXiv2022

Passive Laser Power Stabilization via an Optical Spring

Metrology experiments can be limited by the noise produced by the laser involved via small fluctuations in the laser's power or frequency. Typically, active power stabilization schemes consisting of an in-loop sensor and a feedback control loop are employed. Those schemes are fundamentally limited by shot noise coupling at the in-loop sensor. In this letter we propose to use the optical spring effect to passively stabilize the classical power fluctuations of a laser beam. In a proof of principle experiment, we show that the relative power noise of the laser is stabilized from approximately $2 \times 10^{-5}$ Hz$^{-1/2}$ to a minimum value of $1.6 \times 10^{-7}$ Hz$^{-1/2}$, corresponding to the power noise reduction by a factor of $125$. The bandwidth at which stabilization occurs ranges from $400$ Hz to $100$ kHz. The work reported in this letter further paves the way for high power laser stability techniques which could be implemented in optomechanical experiments and in gravitational wave detectors.

physics.optics↗

arXiv2021

Single-mode input squeezing and tripartite entanglement in three-mode ponderomotive optomechanics simulations

Quantum entanglement is a crucial resource for a wide variety of quantum technologies. However, the current state-of-art methods to generate quantum entanglement in optomechanical systems are not as efficient as all-optical methods utilizing nonlinear crystals. This article proposes a new scheme in which two single-mode squeezed light fields are injected into an optomechanical cavity. We demonstrate through our numerical simulations that the quantum entanglement can be substantially enhanced with the careful selection of squeezing strength and squeezing angle of the two quadrature squeezed light fields. Our results represent a significant improvement in output bipartite photon-photon entanglement over the previously demonstrated schemes using two coherent light fields as inputs. These simulations predict a maximum increase in bipartite optical entanglement by a factor of about 6, as well as increases in the quantum noise of the output light. A perceived loss of quantum information at certain squeezing angles is attributed to tripartite entanglement between the two optical fields and the optomechanical oscillator (OMO). At particular squeezing angles, the bipartite (or tripartite) entanglement can be increased, thus introducing a method of optically controlling the intracavity entanglement. These mechanics can benefit various optical quantum technologies utilizing optomechanical entanglement and continuous variable quantum optics.

quant-ph↗

arXiv2020

Mechanical Quantum Sensing in the Search for Dark Matter

Numerous astrophysical and cosmological observations are best explained by the existence of dark matter, a mass density which interacts only very weakly with visible, baryonic matter. Searching for the extremely weak signals produced by this dark matter strongly motivate the development of new, ultra-sensitive detector technologies. Paradigmatic advances in the control and readout of massive mechanical systems, in both the classical and quantum regimes, have enabled unprecedented levels of sensitivity. In this white paper, we outline recent ideas in the potential use of a range of solid-state mechanical sensing technologies to aid in the search for dark matter in a number of energy scales and with a variety of coupling mechanisms.

physics.ins-det↗

arXiv2020

Optomechanical entanglement at room temperature: a simulation study with realistic conditions

Quantum entanglement is the key to many applications like quantum key distribution, quantum teleportation, and quantum sensing. However, reliably generating quantum entanglement in macroscopic systems has proved to be a challenge. Here, we present a detailed analysis of ponderomotive entanglement generation which utilizes optomechanical interactions to create quantum correlations. We numerically calculate an entanglement measure -- the logarithmic negativity -- for the quantitative assessment of the entanglement. Experimental limitations, including thermal noise and optical loss, from measurements of an existing experiment were included in the calculation, which is intractable to solve analytically. This work will play an important role in the development of ponderomotive entanglement devices.

quant-ph↗

arXiv2020

A Cryogenic Silicon Interferometer for Gravitational-wave Detection

The detection of gravitational waves from compact binary mergers by LIGO has opened the era of gravitational wave astronomy, revealing a previously hidden side of the cosmos. To maximize the reach of the existing LIGO observatory facilities, we have designed a new instrument that will have 5 times the range of Advanced LIGO, or greater than 100 times the event rate. Observations with this new instrument will make possible dramatic steps toward understanding the physics of the nearby universe, as well as observing the universe out to cosmological distances by the detection of binary black hole coalescences. This article presents the instrument design and a quantitative analysis of the anticipated noise floor.

astro-ph.IM↗

arXiv2019

Design of Microresonators to Minimize Thermal Noise Below the Standard Quantum Limit

We present a design for a new microresonator whose geometry is optimized to maximize sub-Standard Quantum Limit (SQL) performance. The new design is predicted to have thermal noise well below the SQL across a broad range of frequencies when operated at 10K. The performance of this designed microresonator will allow it to serve as a test-bed for quantum non-demolition measurements, and to open new regimes of precision measurement that are relevant for many practical sensing applications, including advanced gravitational wave detectors.

quant-ph↗

arXiv2019

Exploring the sensitivity of gravitational wave detectors to neutron star physics

The physics of neutron stars can be studied with gravitational waves emitted from coalescing binary systems. Tidal effects become significant during the last few orbits and can be visible in the gravitational-wave spectrum above 500 Hz. After the merger, the neutron star remnant oscillates at frequencies above 1 kHz and can collapse into a black hole. Gravitational-wave detectors with a sensitivity of ~10^{-24} strain/sqHz at 2-4 kHz can observe these oscillations from a source which is ~100 Mpc away. The current observatories, such as LIGO and Virgo, are limited by shot noise at high frequencies and have a sensitivity of > 2 * 10^{-23} strain/sqHz at 3 kHz. In this paper, we propose an optical configuration of gravitational-wave detectors which can be set up in present facilities using the current interferometer topology. This scheme has a potential to reach 7 * 10^{-25} strain/sqHz at 2.5 kHz without compromising the detector sensitivity to black hole binaries. We argue that the proposed instruments have a potential to detect similar amount of post-merger neutron star oscillations as the next generation detectors, such as Cosmic Explorer and Einstein Telescope. We also optimise the arm length of the future detectors for neutron star physics and find that the optimal arm length is ~20 km. These instruments have the potential to observe neutron star post-merger oscillations at a rate of ~30 events per year with a signal-to-noise ratio of 5 or more.

astro-ph.IM↗

arXiv2018

Quantum back action cancellation in the audio band

We report on the cancellation of quantum back action noise in an optomechanical cavity. We perform two measurements of the displacement of the microresonator, one in reflection of the cavity, and one in transmission of the cavity. We show that measuring the amplitude quadrature of the light in transmission of the optomechanical cavity allows us to cancel the back action noise between 1 kHz and 50 kHz, and obtain a more sensitive measurement of the microresonator's position. To confirm that the back action is eliminated, we measure the noise in the transmission signal as a function of circulating power. By splitting the transmitted light onto two photodetectors and cross correlating the two signals, we remove the contributon from shot noise and measure a quantum noise free thermal noise spectrum. Eliminating the effects of back action in this frequency regime is an important demonstration of a technique that could be used to mitigate the effects of back action in interferometric gravitational wave detectors such as Advanced LIGO.

quant-ph↗

arXiv2018

Broadband reduction of quantum radiation pressure noise via squeezed light injection

We present the reduction and manipulation of quantum radiation pressure noise (QRPN) in an optomechanical cavity with the injection of squeezed light. The optomechanical system consists of a high-reflectivity single-crystal microresonator which serves as one mirror of a Fabry-Perot cavity. The experiment is performed at room temperature and is QRPN dominated between 10 kHz and 50 kHz, frequencies relevant to gravitational wave observatories. We observed a reduction of 1.2 dB in the measurement noise floor with the injection of amplitude squeezed light generated from a below-threshold degenerate optical parametric oscillator. This experiment is a crucial step in realizing the reduction of QRPN for future interferometric gravitational wave detectors and improving their sensitivity.

quant-ph↗

arXiv2018

Room temperature optomechanical squeezing

The radiation-pressure driven interaction of a coherent light field with a mechanical oscillator induces correlations between the amplitude and phase quadratures of the light. These correlations result in squeezed light -- light with quantum noise lower than shot noise in some quadratures, and higher in others. Due to this lower quantum uncertainty, squeezed light can be used to improve the sensitivity of precision measurements. In particular, squeezed light sources based on nonlinear optical crystals are being used to improve the sensitivity of gravitational wave (GW) detectors. For optomechanical squeezers, thermally driven fluctuations of the mechanical oscillator's position makes it difficult to observe the quantum correlations at room temperature, and at low frequencies. Here we present a measurement of optomechanically (OM) squeezed light, performed at room-temperature, in a broad band near audio-frequency regions relevant to GW detectors. We observe sub-poissonian quantum noise in a frequency band of 30 kHz to 70 kHz with a maximum reduction of 0.7 $\pm$ 0.1 dB below shot noise at 45 kHz. We present two independent methods of measuring this squeezing, one of which does not rely on calibration of shot noise.

quant-ph↗

arXiv2018

Observation of a room-temperature oscillator's motion dominated by quantum fluctuations over a broad audio-frequency band

We report on the broadband measurement of quantum radiation pressure noise (QRPN) in an optomechanical cavity at room temperature over a broad range of frequencies relevant to gravitational-wave detectors. We show that QRPN drives the motion of a high-reflectivity single-crystal microresonator, which serves as one mirror of a Fabry-Perot cavity. In our measurements QRPN dominates over all other noise between 10 kHz and 50 kHz and scales as expected with the circulating power inside the cavity. The thermal noise of the microresonator, the largest noise source next to the QRPN, is measured and shown to agree with a structural damping model from 200 Hz to 30 kHz. By observing the effects of QRPN in the audio-band, we now have a testbed for studying techniques to mitigate back-action, such as variational readout and squeezed light injection, that could be used to improve the sensitivity of gravitational-wave detectors.

quant-ph↗

arXiv2017

Observation of an Optical Spring With a Beamsplitter

We present the experimental observation of an optical spring without the use of an optical cavity. The optical spring is produced by interference at a beamsplitter and, in principle, does not have the damping force associated with optical springs created in detuned cavities. The experiment consists of a Michelson-Sagnac interferometer (with no recycling cavities) with a partially reflective GaAs microresonator as the beamsplitter that produces the optical spring. Our experimental measurements at input powers of up to 360 mW show the shift of the optical spring frequency as a function of power and are in excellent agreement with theoretical predictions. In addition, we show that the optical spring is able to keep the interferometer stable and locked without the use of external feedback.

physics.optics↗

arXiv2017

Radiation-Pressure-Mediated Control of an Optomechanical Cavity

We describe and demonstrate a method to control a detuned movable-mirror Fabry-Perot cavity using radiation pressure in the presence of a strong optical spring. At frequencies below the optical spring resonance, self-locking of the cavity is achieved intrinsically by the optomechanical (OM) interaction between the cavity field and the movable end mirror. The OM interaction results in a high rigidity and reduced susceptibility of the mirror to external forces. However, due to a finite delay time in the cavity, this enhanced rigidity is accompanied by an anti-damping force, which destabilizes the cavity. The cavity is stabilized by applying external feedback in a frequency band around the optical spring resonance. The error signal is sensed in the amplitude quadrature of the transmitted beam with a photodetector. An amplitude modulator in the input path to the cavity modulates the light intensity to provide the stabilizing radiation pressure force.

quant-ph↗

arXiv2016

A Stable Optical Trap from a Single Optical Field Utilizing Birefringence

We report a stable double optical spring effect in an optical cavity pumped with a single optical field that arises as a result of birefringence. One end of the cavity is formed by a multilayer Al$_{0.92}$Ga$_{0.08}$As/GaAs stack supported by a microfabricated cantilever, with a natural mode frequency of $274$ Hz. The optical spring shifts the resonance to $21$ kHz, corresponding to a suppression of low frequency vibrations by a factor of more than $10^{4}$. The stable nature of the optical trap allows the cavity to be operated without any external feedback and with only a single optical field incident.

physics.optics↗

arXiv2013

Suppression of quantum-radiation-pressure noise in an optical spring

Recent advances in micro- and nanofabrication techniques have led to corresponding improvement in the performance of optomechanical systems, which provide a promising avenue towards quantum-limited metrology and the study of quantum behavior in macroscopic mechanical objects. One major impediment to reaching the quantum regime is thermal excitation, which can be overcome for sufficiently high mechanical quality factor Q. Here, we propose a method for increasing the effective Q of a mechanical resonator by stiffening it via the optical spring effect exhibited by linear optomechanical systems, and show how the associated quantum radiation pressure noise can be evaded by sensing and feedback control. In a parameter regime that is attainable with current technology, this method allows for realistic quantum cavity optomechanics in a frequency band well below that which has been realized thus far.

quant-ph↗