arXiv subjects

Ute Kaiser

Publications and source records attributed to Ute Kaiser.

At least 19 recordsLinked to original sources

arXiv2026

Bottom-up Synthesis of Metastable 2D Hexagonal Copper(I) Iodide on Monolayer and within Bilayer Graphene

Copper(I) iodide (CuI) is a wide-bandgap semiconductor crystallizing in the 3D $\gamma$-phase under ambient conditions; its layered van der Waals bulk phase $\beta$-CuI is stable only between 643 and 673 K. The two-dimensional (2D) h-CuI form has been obtained via liquid-phase exfoliation of mechanochemically prepared precursors and via encapsulation between graphene sheets, whereas bottom-up growth of 2D h-CuI on open surfaces has not yet been demonstrated. Here, we report a vapor-phase synthesis of h-CuI directly on low-defect, large-area monolayer and within bilayer reduced oxo-graphene (r-oxo-G) at low temperatures. Using a copper TEM grid as the solid-state precursor for copper, HI-vapor exposure at 40 $\deg$C initiates nucleation, while annealing at 180 $\deg$C promotes the growth of extended h-CuI domains. Aberration-corrected HRTEM resolves the atomic structure, local twist angles, and lattice anisotropy of the CuI/r-oxo-G nanohybrid, while STEM-EDX yields a Cu:I ratio consistent with 1:1. First-principles calculations show that van der Waals adhesion to graphene stabilizes the supported hexagonal layer. Under the presented low-temperature precursor conditions, pathways for nucleation of the $\gamma$-phase are not available, allowing the hexagonal phase to form selectively at the graphene interface. Ab initio molecular dynamics simulations show that the heterostructure retains its hexagonal lattice order at 600 K, including on an open monolayer graphene support. The lateral extent of the growth is limited mainly by remaining interfacial adsorbates. These results establish a route to metastable 2D h-CuI on a chemically inert graphene template, which may be useful for wide-bandgap electronic and optoelectronic devices.

cond-mat.mtrl-sci↗

arXiv2026

CVD Grown Hybrid MoSe$_2$-WSe$_2$ Lateral/Vertical Heterostructures with Strong Interlayer Exciton Emission

Lateral heterostructures of 2D transition metal dichalcogenide offer a powerful platform to investigate photonic and electronic phenomena at atomically sharp interfaces. However, their controlled engineering, including tuning lateral domain size and integration into vertical van der Waals heterostructures with other 2D materials, remains challenging. Here, we present a facile route for the synthesis of two types of heterostructures consisting of monolayers of MoSe$_2$ and WSe$_2$ - purely lateral (HS I) and hybrid lateral/vertical (HS II) - using liquid precursors of transition metal salts and chemical vapor deposition (CVD). Depending on the growth parameters, the heterostructure type and their lateral dimensions can be adjusted. We characterized properties of the HS I and HS II by complementary spectroscopic and microscopic techniques including Raman and photoluminescence spectroscopy, and optical and atomic force microscopy, and scanning electron and transmission electron microscopy. The photoluminescence measurements reveal strong interlayer exciton emission in the MoSe$_2$/WSe$_2$ region of HS II, which dominates the spectrum at 4 K and persisting up to room temperature. These results demonstrate high optical quality of the grown heterostructures which in combination with scalability of the developed approach paves the way for fundamental studies and device applications based on these unique 2D quantum materials.

cond-mat.mtrl-sci↗

arXiv2025

Beyond the band edge: Unveiling high-mobility hot carriers in a two-dimensional conjugated coordination polymer

Hot carriers, inheriting excess kinetic energy from high-energy photons, underpin numerous optoelectronic applications involving non-equilibrium transport processes. Current research on hot carriers has predominantly focused on inorganic materials, with little attention paid to organic-based systems due to their ultrafast energy relaxation and inefficient charge transport. Here, we overturn this paradigm by demonstrating highly mobile hot carriers in solution-processable, highly crystalline two-dimensional conjugated coordination polymer (2D c-CP) Cu3BHT (BHT = benzenehexathiol) films. Leveraging a suite of ultrafast spectroscopic and imaging techniques, we unravel the microscopic charge transport landscape in Cu3BHT films following non-equilibrium photoexcitation across temporal, spatial, and frequency domains, revealing two distinct high-mobility transport regimes. In the non-equilibrium transport regime, hot carriers achieve ultrahigh mobility of ~2,000 cm2 V-1 s-1, traversing grain boundaries up to 300 nm within a picosecond. In the quasi-equilibrium transport regime, free carriers exhibit Drude-type band-like transport with a remarkable mobility of ~400 cm2 V-1 s-1 and an intrinsic diffusion length exceeding 1 micrometer. These findings establish 2D c-CPs as versatile platforms for exploring high-mobility non-equilibrium transport, unlocking new opportunities for organic-based hot carrier applications.

cond-mat.mtrl-sci↗

arXiv2023

Giant proton transmembrane transport through sulfophenylated graphene in a direct methanol fuel cell

An ideal proton exchange membrane should only permeate protons and be leak tight for fuels. Graphene is impermeable to water and poorly conducting to protons. Here, we chemically functionalized monolayer graphene to install sulfophenylated sp3 dislocations by diazotization. Selective to protons, transmembrane areal conductances are up to ~50 S/cm2, which is ~5000 fold higher than in pristine graphene. Mounted in a direct methanol fuel cell, sulfophenylated graphene resulted in power densities up to 1.6 W/mg or 123 mW/cm under standard cell operation (60 C), a value ~two-fold larger than micron-thick films of Nafion 117. The combination of sp3 dislocations and polar groups, therefore, allow the creation of hydrophilic ion paths through graphene and unveils a novel route to rationalize transmembrane hydron transport through 2D materials.

physics.chem-ph↗

arXiv2023

A Cu3BHT-Graphene van der Waals Heterostructure with Strong Interlayer Coupling

Two dimensional van der Waals heterostructures (2D are of significant interest due to their intriguing physical properties that are critically defined by the constituent monolayers and their interlayer coupling . However, typical inorganic 2 D vdWhs fall into the weakly coupled region, limiting efficient interfacial charge flow crucial for developing high performance quantum opto electronics. Here, we demonstrate strong interlayer coupling in Cu3 BHT (BHT = benzenehexathiol) graphene vdWhs an organic inorganic bilayer characterized by prominent interlayer charge transfer Monolayer Cu3 BHT with a Kagome lattice is synthesized on the water surface and then coupled with graphene to produce a cm2 scale 2D vdWh. Spectroscopic and electrical studies, along with theoretical calculation s show significant hole transfer from monolayer Cu3 BHT to graphene upon contact , being characteristic fingerprints for strong interlayer coupling This study unveils the great potential of integrating highly pi-conjugated 2D coordination polymers (2DCPs) into 2D vdWhs to explor e intriguing physical phenomena.

physics.app-ph↗

arXiv2022

Exciton spectroscopy and diffusion in MoSe2-WSe2 lateral heterostructures encapsulated in hexagonal boron nitride

Chemical vapor deposition (CVD) allows lateral edge epitaxy of transition metal dichalcogenide heterostructures with potential applications in optoelectronics. Critical for carrier and exciton transport is the quality of the two materials that constitute the monolayer and the nature of the lateral heterojunction. Important details of the optical properties were inaccessible in as-grown heterostructure samples due to large inhomogeneous broadening of the optical transitions. Here we perform optical spectroscopy at T = 4 K and also at 300 K to access the optical transitions in CVD grown MoSe2-WSe2 lateral heterostructures that are transferred from the growth-substrate and are encapsulated in hBN. Photoluminescence (PL), reflectance contrast and Raman spectroscopy reveal considerably narrowed optical transition linewidth similar to high quality exfoliated monolayers. In high-resolution transmission electron microscopy (HRTEM) we find near-atomically sharp junctions with a typical extent of 3nm for the covalently bonded MoSe2-WSe2. In PL imaging experiments we find effective excitonic diffusion length that are longer for WSe2 than for MoSe2 at low T=4 K, whereas at 300 K this trend is reversed.

cond-mat.mtrl-sci↗

arXiv2020

Well-defined sub-nanometer graphene ribbons synthesized inside carbon nanotubes

Graphene nanoribbons with sub-nanometer widths are extremely interesting for nanoscale electronics and devices as they combine the unusual transport properties of graphene with the opening of a band gap due to quantum confinement in the lateral dimension. Strong research efforts are presently paid to grow such nanoribbons. Here we show the synthesis of 6- and 7-armchair graphene nanoribbons, with widths of 0.61 and 0.74 nm, and excitonic gaps of 1.83 and 2.18 eV, by high-temperature vacuum annealing of ferrocene molecules inside single-walled carbon nanotubes. The encapsulation of the so-obtained graphene nanoribbons is proved by atomic resolution electron microscopy, while their assignment is provided by a combination of an extensive wavelength-dependent Raman scattering characterization and quantum-chemical calculations. These findings enable a facile and scalable approach leading to the controlled growth and detailed analysis of well-defined sub-nanometer graphene nanoribbons.

cond-mat.mtrl-sci↗

arXiv2020

Proton and Li-Ion Permeation through Graphene with Eight-Atom-Ring Defects

Defect-free graphene is impermeable to gases and liquids but highly permeable to thermal protons. Atomic-scale defects such as vacancies, grain boundaries and Stone-Wales defects are predicted to enhance graphene's proton permeability and may even allow small ions through, whereas larger species such as gas molecules should remain blocked. These expectations have so far remained untested in experiment. Here we show that atomically thin carbon films with a high density of atomic-scale defects continue blocking all molecular transport, but their proton permeability becomes ~1,000 times higher than that of defect-free graphene. Lithium ions can also permeate through such disordered graphene. The enhanced proton and ion permeability is attributed to a high density of 8-carbon-atom rings. The latter pose approximately twice lower energy barriers for incoming protons compared to the 6-atom rings of graphene and a relatively low barrier of ~0.6 eV for Li ions. Our findings suggest that disordered graphene could be of interest as membranes and protective barriers in various Li-ion and hydrogen technologies.

cond-mat.mtrl-sci↗

arXiv2019

Accessing high optical quality of MoS2 monolayers grown by chemical vapor deposition

Chemical vapor deposition (CVD) allows growing transition metal dichalcogenides (TMDs) over large surface areas on inexpensive substrates. In this work, we correlate the structural quality of CVD grown MoS$_2$ monolayers (MLs) on SiO$_2$/Si wafers studied by high-resolution transmission electron microscopy (HRTEM) with high optical quality revealed in optical emission and absorption from cryogenic to ambient temperatures. We determine a defect concentration of the order of 10$^{13}$ cm$^{-2}$ for our samples with HRTEM. To have access to the intrinsic optical quality of the MLs, we remove the MLs from the SiO$_2$ growth substrate and encapsulate them in hBN flakes with low defect density, to reduce the detrimental impact of dielectric disorder. We show optical transition linewidth of 5 meV at low temperature (T=4 K) for the free excitons in emission and absorption. This is comparable to the best ML samples obtained by mechanical exfoliation of bulk material. The CVD grown MoS$_2$ ML photoluminescence is dominated by free excitons and not defects even at low temperature. High optical quality of the samples is further confirmed by the observation of excited exciton states of the Rydberg series. We optically generate valley coherence and valley polarization in our CVD grown MoS$_2$ layers, showing the possibility for studying spin and valley physics in CVD samples of large surface area.

cond-mat.mes-hall↗

arXiv2019

Templated direct growth of ultra-thin double-walled carbon nanotubes

Double-walled carbon nanotubes (DWCNTs) combined the advantages of multi-walled (MW-) and single-walled (SW-) CNTs can be obtained by transforming the precursors (e.g. fullerene, ferrocene) into thin inner CNTs inside SWCNTs as templates. However, this method is limited since the DWCNT yield is strongly influenced by the filling efficiency (depending on the type of the filled molecules), opening and cutting the SWCNTs, and the diameter of the host SWCNTs. Therefore, it cannot be applied to all types of SWCNT templates. Here we show a universal route to synthesize ultra-thin DWCNTs via making SWCNTs stable at high temperature in vacuum. This method applies to different types of SWCNTs including metallicity-sorted ones without using any precursors since the carbon sources were from the reconstructed SWCNTs and the residue carbons. The resulting DWCNTs are with high quality and the yield of inner tubes is comparable to/higher than that of the DWCNTs made from the transformation of ferrocene/fullerene peapods.

cond-mat.mtrl-sci↗

arXiv2019

Extraction of Linear Carbon Chains Unravels the Role of the Carbon Nanotube Host

Linear carbon chains (LCCs) have been shown to grow inside double-walled carbon nanotubes (DWCNTs) but isolating them from this hosting material represents one of the most challenging tasks towards applications. Herein we report the extraction and separation of LCCs inside single-wall carbon nanotubes (LCCs@SWCNTs) extracted from a double walled host LCCs@DWCNTs by applying a combined tip-ultrasonic and density gradient ultracentrifugation (DGU) process. High-resolution transmission electron microscopy (HRTEM), optical absorption, and Raman spectroscopy show that not only short LCCs but clearly long LCCs (LLCCs) can be extracted and separated from the host. Moreover, the LLCCs can even be condensed by DGU. The Raman spectral frequency of LCCs remains almost unchanged regardless of the presence of the outer tube of the DWCNTs. This suggests that the major importance of the outer tubes is making the whole synthesis viable. We have also been able to observe the interaction between the LCCs and the inner tubes of DWCNTs, playing a major role in modifying the optical properties of LCCs. Our extraction method suggests the possibility towards the complete isolation of LCCs from CNTs.

cond-mat.mtrl-sci↗

arXiv2018

Efficient first principles simulation of electron scattering factors for transmission electron microscopy

Electron microscopy is a powerful tool for studying the properties of materials down to their atomic structure. In many cases, the quantitative interpretation of images requires simulations based on atomistic structure models. These typically use the independent atom approximation that neglects bonding effects, which may, however, be measurable and of physical interest. Since all electrons and the nuclear cores contribute to the scattering potential, simulations that go beyond this approximation have relied on computationally highly demanding all-electron calculations. Here, we describe a new method to generate ab initio electrostatic potentials when describing the core electrons by projector functions. Combined with an interface to quantitative image simulations, this implementation enables an easy and fast means to model electron microscopy images. We compare simulated transmission electron microscopy images and diffraction patterns to experimental data, showing an accuracy equivalent to earlier all-electron calculations at a much lower computational cost.

cond-mat.mtrl-sci↗

arXiv2018

Lateral heterostructures of two-dimensional materials by electron-beam induced stitching

We present a novel methodology to synthesize two-dimensional (2D) lateral heterostructures of graphene and MoS2 sheets with molecular carbon nanomembranes (CNMs), which is based on electron beam induced stitching. Monolayers of graphene and MoS2 were grown by chemical vapor deposition (CVD) on copper and SiO2 substrates, respectively, transferred onto gold/mica substrates and patterned by electron beam lithography or photolithography. Self-assembled monolayers (SAMs) of aromatic thiols were grown on the gold film in the areas where the 2D materials were not present. An irradiation with a low energy electron beam was employed to convert the SAMs into CNMs and simultaneously stitching the CNM edges to the edges of graphene and MoS2, therewith forming a heterogeneous but continuous film composed of two different materials. The formed lateral heterostructures possess a high mechanical stability, enabling their transfer from the gold substrate onto target substrates and even the preparation as freestanding sheets. We characterized the individual steps of this synthesis and the structure of the final heterostructures by complementary analytical techniques including optical microscopy, Raman spectroscopy, atomic force microscopy (AFM), helium ion microscopy (HIM), X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electron microscopy (HRTEM) and find that they possess nearly atomically sharp boundaries.

cond-mat.mes-hall↗

arXiv2017

Formation of nickel clusters wrapped in carbon cages: towards new endohedral metallofullerene synthesis

In spite of the high potential of endohedral metallofullerenes (EMFs) for application in biology, medicine and molecular electronics and recent efforts in EMF synthesis, the variety of EMFs accessible by conventional synthetic methods remains limited and does not include, for example, EMFs of late transition metals. We propose a method in which EMF formation is initiated by electron irradiation in aberration-corrected high-resolution transmission electron spectroscopy (AC-HRTEM) of a metal cluster surrounded by amorphous carbon inside a carbon nanotube serving as a nano-reactor and apply this method for synthesis of nickel EMFs. The use of ACHRTEM makes it possible not only to synthesize new, previously unattainable nanoobjects but also to study in situ the mechanism of structural transformations. Molecular dynamics simulations using the state-of-the-art approach for modeling the effect of electron irradiation are performed to rationalise the experimental observations and to link the observed processes with conditions of bulk EMF synthesis.

cond-mat.mes-hall↗

arXiv2017

Organic Nanodiamonds

Nano-crystalline diamond is a new carbon phase with numerous intriguing physical and chemical properties and applications. Small doped nanodiamonds for example do find increased use as novel quantum markers in biomedical applications. However, growing doped nanodiamonds below sizes of 5 nm with controlled composition has been elusive so far. Here we grow nanodiamonds under conditions where diamond-like organic seed molecules do not decompose. This is a key first step toward engineered growth of fluorescent nanodiamonds wherein a custom designed seed molecule can be incorporated at the center of a nanodiamond. By substituting atoms at particular locations in the seed molecule it will be possible to achieve complex multi-atom diamond color centers or even to engineer complete nitrogen-vacancy (NV) quantum registers. Other benefits include the potential to grow ultrasmall nanodiamonds, wherein each diamond no matter how small can have at least one bright and photostable fluorescent emitter.

physics.chem-ph↗

arXiv2016

Mapping atomic orbitals with the transmission electron microscope: Images of defective graphene predicted from first-principles theory

Transmission electron microscopy has been a promising candidate for mapping atomic orbitals for a long time. Here, we explore its capabilities by a first principles approach. For the example of defected graphene, exhibiting either an isolated vacancy or a substitutional nitrogen atom, we show that three different kinds of images are to be expected, depending on the orbital character. To judge the feasibility of visualizing orbitals in a real microscope, the effect of the optics aberrations is simulated. We demonstrate that, by making use of energy-filtering, it should indeed be possible to map atomic orbitals in a state-of-the-art transmission electron microscope.

cond-mat.mtrl-sci↗

arXiv2015

Numerical correction of anti-symmetric aberrations in single HRTEM images of weakly scattering 2D-objects

Here, we present a numerical post-processing method for removing the effect of anti-symmetric residual aberrations in high-resolution transmission electron microscopy (HRTEM) images of weakly scattering 2D-objects. The method is based on applying the same aberrations with the opposite phase to the Fourier transform of the recorded image intensity and subsequently inverting the Fourier transform. We present the theoretical justification of the method and its verification based on simulated images in the case of low-order anti-symmetric aberrations. Ultimately the method is applied to experimental hardware aberration-corrected HRTEM images of single-layer graphene and MoSe2 resulting in images with strongly reduced residual low-order aberrations, and consequently improved interpretability. Alternatively, this method can be used to estimate by trial and error the residual anti-symmetric aberrations in HRTEM images of weakly scattering objects.

cond-mat.mtrl-sci↗

arXiv2015

Implantation and atomic scale investigation of self-interstitials in graphene

Crystallographic defects play a key role in determining the properties of crystalline materials. The new class of two-dimensional materials, foremost graphene, have enabled atomically resolved studies of defects, such as vacancies, grain boundaries, dislocations, and foreign atom substitutions. However, atomic resolution imaging of implanted self-interstitials has so far not been reported in any three- but also not in any two-dimensional material. Here, we deposit extra carbon into single-layer graphene at soft landing energies of ~1 eV using a standard carbon coater. We identify all the self-interstitial dimer structures theoretically predicted earlier, employing 80 kV aberration-corrected high-resolution transmission electron microscopy. We demonstrate accumulation of the interstitials into larger aggregates and dislocation dipoles, which we predict to have strong local curvature by atomistic modeling, and to be energetically favourable configurations as compared to isolated interstitial dimers. Our results contribute to the basic knowledge on crystallographic defects, and lay out a pathway into engineering the properties of graphene by pushing the crystal into a state of metastable supersaturation.

cond-mat.mtrl-sci↗