arXiv subjects

V. F. Nesterenko

Publications and source records attributed to V. F. Nesterenko.

At least 19 recordsLinked to original sources

arXiv2015

Attenuation of short strongly nonlinear stress pulses in dissipative granular chains

Attenuation of short, strongly nonlinear stress pulses in chains of spheres and cylinders was investigated experimentally and numerically for two ratios of their masses keeping their contacts identical. The chain with mass ratio 0.98 supports solitary waves and another one (with mass ratio 0.55) supports nonstationary pulses which preserve their identity only on relatively short distances, but attenuate on longer distances because of radiation of small amplitude tails generated by oscillating small mass particles. Pulse attenuation in experiments in the chain with mass ratio 0.55 was faster at the same number of the particles from the entrance than in the chain with mass ratio 0.98. It is in quantitative agreement with results of numerical calculations with effective damping coefficient 6 kg/s. This level of damping was critical for eliminating the gap openings between particles in the system with mass ratio 0.55 present at lower or no damping. However with increase of dissipation numerical results show that the chain with mass ratio 0.98 provides faster attenuation than chain with mass ratio 0.55 due to the fact that the former system supports the narrower pulse with the larger difference between velocities of neighboring particles. The investigated chains demonstrated different wave structure at zero dissipation and at intermediate damping coefficients and the similar behavior at large damping.

nlin.PS↗

arXiv2013

Transmission and reflection of strongly nonlinear solitary waves at granular interfaces

The interaction of a solitary wave front with an interface formed by two strongly-nonlinear non-cohesive granular lattices displays rich behaviour, characterized by the breakdown of continuum equations of motion in the vicinity of the interface. By treating the solitary wave as a quasiparticle with an effective mass, we construct an intuitive (energy and linear momentum conserving) discrete model to predict the amplitudes of the transmitted solitary waves generated when an incident solitary wave front, parallel to the interface, moves from a denser to a lighter granular hexagonal lattice. Our findings are corroborated with simulations. We then successfully extend this model to oblique interfaces, where we find that the angle of refraction and reflection of a solitary wave follows, below a critical value, an analogue of Snell's law in which the solitary wave speed replaces the speed of sound, which is zero in the sonic vacuum.

cond-mat.soft↗

arXiv2012

Mechanisms of fragmentation of Al-W granular composites under dynamic loading

Numerical simulations of Aluminum (Al) and Tungsten (W) granular composite rings under various dynamic loading conditions caused by explosive loading were examined. Three competing mechanisms of fragmentation were observed: a continuum level mechanism generating large macrocracks described by the Grady-Kipp fragmentation mechanism, a mesoscale mechanism generating voids and microcracks near the initially unbonded Al/W interfaces due to tensile strains, and a mesoscale jetting due to the development of large velocity gradients between the W particles and adjacent Al. These mesoscale mechanisms can be used to tailor the size of the fragments by selecting an appropriate initial mesostructure for a given loading condition.

cond-mat.mtrl-sci↗

arXiv2011

Role of material properties and mesostructure on dynamic deformation and shear instability in Al-W granular composites

Dynamic experiments with Al-W granular/porous composites revealed qualitatively different behavior with respect to shear localization depending on bonding between Al particles. Two-dimensional numerical modeling was used to explore the mesomechanics of the large strain dynamic deformation in Al-W granular/porous composites and explain the experimentally observed differences in shear localization between composites with various mesostructures. Specifically, the bonding between the Al particles, the porosity, the roles of the relative particle sizes of Al and W, the arrangements of the W particles, and the material properties of Al were investigated using numerical calculations. It was demonstrated in simulations that the bonding between the "soft" Al particles facilitated shear localization as seen in the experiments. Numerical calculations and experiments revealed that the mechanism of the shear localization in granular composites is mainly due to the local high strain flow of "soft" Al around the "rigid" W particles causing localized damage accumulation and subsequent growth of the meso/macro shear bands/cracks. The "rigid" W particles were the major geometrical factor determining the initiation and propagation of "kinked" shear bands in the matrix of "soft" Al particles, leaving some areas free of extensive plastic deformation as observed in experiments and numerical calculations.

cond-mat.soft↗

arXiv2008

Tunable frequency band-gap and pulse propagation in a strongly nonlinear diatomic chain

One-dimensional nonlinear phononic crystals have been assembled from periodic diatomic chains of stainless steel cylinders alternated with Polytetrafluoroethylene (PTFE) spheres. We report the presence of acoustic band gaps in the dispersion relation of the linearized systems and study the transformation of single and multiple pulses in linear, nonlinear and strongly nonlinear regimes with numerical calculations and experiments. The limiting frequencies of the band gap are within the audible frequency range (20-20,000 Hz) and can be tuned by varying the particle's material properties, mass and initial compression. Pulses rapidly transform within very short distances from the impacted end due to the influence of the band gap in the linear and in nonlinear elastic chains. The effects of an in situ band gap created by a mean dynamic compression are observed in the strongly nonlinear wave regime.

cond-mat.soft↗

arXiv2008

Particle size effect on strength, failure and shock behavior in Polytetrafluoroethylene-Al-W granular composites

The variation of metallic particle size and sample porosity significantly alters the dynamic mechanical properties of high density granular composites processed using a cold isostatically pressed mixture of polytetrafluoroethylene (PTFE), aluminum (Al) and tungsten (W) powders. Quasi-static and dynamic experiments are performed with identical constituent mass fractions with variations in the size of the W particles and pressing conditions. The relatively weak polymer matrix allows the strength and fracture modes of this material to be governed by the granular type behavior of agglomerated metal particles. A higher ultimate compressive strength was observed in relatively high porosity samples with small W particles compared to those with coarse W particles in all experiments. Mesoscale granular force chains comprised of the metallic particles explain this unusual phenomenon as observed in a hydrocode simulation of a drop-weight test. Macrocracks forming below the critical failure strain for the matrix and unusual behavior due to a competition between densification and fracture in dynamic tests of porous samples were also observed. Shock loading of this granular composite resulted in higher fraction of total internal energy deposition in the soft PTFE matrix, specifically thermal energy, which can be tailored by the W particle size distribution.

cond-mat.soft↗

arXiv2007

The influence of metallic particle size on the mechanical properties of PTFE-Al-W powder composites

The dynamic mechanical properties of reactive materials (e.g., high density mixtures of polytetraflouroethylene (PTFE), aluminum (Al) and tungsten (W) powders) can be tailored by changing the morphology of the particles and porosity. Cold isostatically pressed PTFE-Al-W powder composites with fine metallic particles and a higher porosity exhibited higher ultimate compressive strength than less porous composites having equivalent mass ratios with coarse W particles. The mesoscale force chains between the fine metallic particles are responsible for this unusual phenomenon. We observed macrocracks below the critical failure strain for the matrix and a competition between densification and fracture in some porous samples in dynamic tests.

cond-mat.soft↗

arXiv2007

Solitary and shock waves in discrete double power-law materials

A novel strongly nonlinear laminar metamaterial supporting new types of solitary and shock waves with impact energy mitigating capabilities is presented. It consists of steel plates with intermittent polymer toroidal rings acting as strongly nonlinear springs with large allowable strain. Their force-displacement relationship is described by the addition of two power-law relationships resulting in a solitary wave speed and width depending on the amplitude. This double nonlinearity allows splitting of an initial impulse into two separate strongly nonlinear solitary wave trains. Solitary and shock waves are observed experimentally and analyzed numerically in an assembly with Teflon o-rings.

cond-mat.soft↗

arXiv2007

Simulation of Particle Size Effect on Dynamic Properties and Fracture of PTFE-W-Al Composites

Recent investigations of the dynamic compressive strength of cold isostatically pressed composites of polytetrafluoroethylene (PTFE), tungsten (W) and aluminum (Al) powders show significant differences depending on the size of metallic particles. The addition of W increases the density and overall strength of the sample. To investigate relatively large deformations multi-material Eulerian and arbitrary Lagrangian-Eulerian methods, which have the ability to efficiently handle the formation of free surfaces, were used. The calculations indicate that the increased strength of the sample with fine metallic particles is due to the formation of force chains under dynamic loading. This phenomenon occurs even at larger porosity of the PTFE matrix in comparison with samples with larger particle size of W and higher density of the PTFE matrix.

cond-mat.soft↗

arXiv2006

Shock Wave Structure in a Strongly Nonlinear Granular Lattice with Viscous Dissipation

The shock wave structure in a one-dimensional lattice (e.g. granular chain) with a power law dependence of force on displacement between particles with viscous dissipation is considered and compared to the corresponding long wave approximation. A dissipative term depending on the relative velocity between neighboring particles is included in the discrete model to investigate its influence on the shape of steady shock profiles. The critical viscosity coefficient is obtained from the long-wave approximation for arbitrary values of the exponent n and denotes the transition from an oscillatory to a monotonic shock profile in stronly nonlinear systems. The expression for the critical viscosity coefficient converges to the known equation for the critical viscosity in the weakly nonlinear case. Values of viscosity based on this expression are comparable to the values obtained in the numerical analysis of a discrete particle lattice with a Herzian contact interaction corresponding to n = 3/2. An initial disturbance in a discrete system approaches a stationary shock profile after traveling a short distance that is comparable to the width of the leading pulse of a stationary shock front. The shock front width is minimized when the viscosity is equal to its critical value.

cond-mat.soft↗

arXiv2005

Influence of Controlled Viscous Dissipation on the Propagation of Strongly Nonlinear Waves in Stainless Steel Based Phononic Crystals

Strongly nonlinear phononic crystals were assembled from stainless steel spheres. Single solitary waves and splitting of an initial pulse into a train of solitary waves were investigated in different viscous media using motor oil and non-aqueous glycerol to introduce a controlled viscous dissipation. Experimental results indicate that the presence of a viscous fluid dramatically altered the splitting of the initial pulse into a train of solitary waves. Numerical simulations qualitatively describe the observed phenomena only when a dissipative term based on the relative velocity between particles is introduced.

cond-mat.soft↗

arXiv2005

Strongly nonlinear wave dynamics in a chain of polymer coated beads

Strongly nonlinear phononic crystals were assembled from a chain of Parylene-C coated steel spheres in a polytetrafluoroethylene (PTFE) holder. This system exhibits strongly nonlinear properties and extends the range of materials supporting "sonic vacuum" type behavior. The combination of a high density core and a soft (low elastic modulus) coating ensures a relatively low velocity of wave propagation. The beads contact interaction caused by the deformation of the Parylene coating can be described as classical nonlinear Hertz theory despite the viscoelastic nature of the polymer and the high strain rate deformation of the contact area. Strongly nonlinear solitary waves excited by impacts were investigated experimentally and compared to chains composed of uniform steel beads. Fracture of the polumer coating was detected under relatively large pulse amplitude.

cond-mat.soft↗

arXiv2005

Energy trapping and shock disintegration in a composite granular medium

Granular materials demonstrate a strongly nonlinear behavior influencing the wave propagation in the medium. We report the first experimental observation of impulse energy confinement and the resultant disintegration of shock and solitary waves. The medium consists of alternating ensambles of high-modulus vs orders of magnitude lower modulus chains of different masses. The trapped energy is contained within the "softer" portions of the composite chain and is slowly released in the form of weak, separated pulses over an extended period of time. This effect is enhanced by using a specific group assembly and superimposed force.

cond-mat.soft↗

arXiv2005

Tunability of solitary wave properties in one dimensional strongly nonlinear phononic crystals

One dimentional strongly nonlinear phononic crystals were assembled from chains of PTFE (polytetrafluoroethylene) and stainless steel spheres with gauges installed inside the beads. Trains of strongly nonlinear solitary waves were excited by an impact. A significant modification of the signal shape and an increase of solitary wave speed up to two times (at the same amplitude of dynamic contact force)were achieved through a noncontact magnetically induced precompression of the chains. Data for PTFE based chains are presented for the first time and data for stainless steel based chains were extended into a smaller range of amplitudes by more than one order of magnitude than previously reported. Experimental results were found to be in reasonable agreement with the long wave approximation and with numerical calculations based on Hertz interaction law for discrete chains.

cond-mat.mtrl-sci↗

arXiv2005

Anomalous wave reflection from the interface of two strongly nonlinear granular media

Granular materials exhibit a strongly nonlinear behaviour affecting the propagation of information in the medium. Dynamically self-organized strongly nonlinear solitary waves are the main information carriers in granular chains. Here we report the first experimental observation of the dramatic change of reflectivity from the interface of two granular media triggered by a noncontact magnetically induced initial precompression. It may be appropriate to name this phenomenon the "acoustic diode" effect. Based on numerical simulations, we explain this effect by the high gradient of particle velocity near the interface.

cond-mat.soft↗

arXiv2005

Strongly nonlinear waves in a chain of Teflon beads

One dimensional "sonic vacuum" type phononic crystals were assembled from a chain of Teflon spheres with different diameters in a Teflon holder. It was demonstrated for the first time that this polymer-based "sonic vacuum", with exceptionally low elastic modulus of particles, supports propagation of strongly nonlinear solitary waves with a very low speed.

cond-mat.soft↗

arXiv2004

Large field generation with Hot Isostatically Pressed Powder-in-Tube MgB2 coil at 25 K

We present the fabrication and test results of Hot-Isostatic-Pressed (HIPed) Powder-in-Tube (PIT) MgB$_2$ coils. The coils properties were measured by transport and magnetization at different applied fields ($H$) and temperatures ($T$). The engineering critical current ($J_e$) value is the largest reported in PIT MgB$_2$ wires or tapes. At 25 K our champion 6-layer coil was able to generate a field of 1 T at self-field ($I_c >$ 220 A, $J_e \sim 2.8 \times 10^4$ A/cm$^2$). At 4 K this coil generated 1.6 T under an applied field of 1.25 T ($I_c \sim350$ A, $J_e \sim 4.5 \times 10^4$ A/cm$^2$). These magnetic fields are high enough for a superconducting transformer or magnet applications such as MRI. A SiC doped MgB$_2$ single layer coil shows a promising improvement at high fields and exhibits $J_c > 10^4$ A/cm$^2$ at 7 T.

cond-mat.supr-con↗

arXiv2003

RF Surface Resistance of a HIPped MgB2 Sample at 21 GHz

Magnesium diboride (MgB2) is attractive for RF cavity application for particle accelerators because it might not show an increase of RF surface losses at high magnetic surface fields, a phenomenon that has prevented high-Tc superconducting materials such as YBCO from being used for this application. We have measured the RF surface resistance (Rs) at 21 GHz of a MgB2 sample fabricated using Hot Isostatic Press (HIP) at 200 MPa and 1000 C. The results show that polishing with 0.1-micron diamond lapping film followed by a 1500-psi DI water rinse in a clean room reduced the Rs by a factor of 6.2 at 15 K and it is the lowest compared to other published data. The Rs data near the lowest temperature (~13 K) scatter between 0.6 and 1.3 mOhm. The penetration depth and energy gap were estimated to be 263 nm and 1.9-2.7, respectively, for the polished surface.

cond-mat.supr-con↗