arXiv subjects

V. Izzo

Publications and source records attributed to V. Izzo.

3 recordsLinked to original sources

arXiv2026

Cherenkov and scintillation light separation in BGO and BSO crystals coupled to SiPMs for dual-readout electromagnetic calorimetry at future colliders

We report on the separation of Cherenkov and scintillation light in BGO and BSO crystals read out with silicon photomultipliers (SiPMs). The two light components are disentangled on an event-by-event basis by combining optical filtering with waveform template fitting, exploiting their distinct spectral and temporal characteristics. Measurements were carried out using high-energy muon and positron beams at the CERN SPS North Area, demonstrating Cherenkov yields of up to $\sim$150 ph.e./GeV in electromagnetic showers. This work provides the first demonstration of Cherenkov-scintillation separation in BGO and BSO crystals with SiPM readout, supporting the use of this technology as a building block for a dual-readout electromagnetic calorimeter, as foreseen in the IDEA detector concept for a future $e^+e^-$ Higgs factory.

physics.ins-det↗

arXiv2018

The Monitoring System of the End-Cap Calorimeter in the Belle II experiment

The Belle II experiment is presently in phase-2 operation at the SuperKEKB electron-positron collider in KEK (Tsukuba, Japan). The detector is an upgrade of the Belle experiment at the KEKB collider and it is optimized for the study of rare B decays, being also sensitive to signals of New Physics beyond the Standard Model. The Electromagnetic Calorimeter (ECL) is based on CsI(Tl) scintillation crystals. It splits in a barrel and two annular end-cap regions, these latter named Forward and Backward, according to the asymmetric design of the collider. CsI(Tl) crystals deliver a high light output at an affordable cost, however their yield changes with temperature and can be permanently damaged by humidity, due to the strong chemical affinity for moisture. Each ECL region is then equipped with thermistors and humidity probes to monitor environmental data. While sensors and cabling have been inherited from the original Belle design, the ECL monitoring system has been fully redesigned. In this paper, we present hardware and software architecture deployed for the 2112 CsI(Tl) crystals arranged in the Forward and Backward end-caps. Single-Board Computers (SBCs) have been designed ad-hoc for embedded applications. For sensor read-out, a data-acquisition system based on 24-bit ADCs with local processing capability has been realized and interfaced with the SBCs. EPICS applications send data across the Local Area Network for remote control and display.

physics.ins-det↗

arXiv2018

The Phase-1 Upgrade for the Level-1 Muon Barrel Trigger of the ATLAS Experiment at LHC

The Level-1 Muon Barrel Trigger of the ATLAS Experiment at LHC makes use of Resistive Plate Chamber (RPC) detectors. The on-detector trigger electronics modules are able to identify muons with predefined transverse momentum values (pT) by executing a coincidence logic on signals coming from the various detector layers. Then, on-detector trigger boards transfer trigger data to the off-detector electronics. A complex trigger system processes the incoming data by combining trigger information from the Barrel and the End-cap regions, and by providing the combined muon candidate to the Central Trigger Processor (CTP). For almost a decade, the Level-1 Trigger system has been operating very well, despite the challenging requirements on trigger efficiency and performance, and the continuously increasing LHC luminosity. In order to cope with these constraints, various upgrades for the full trigger system were already deployed, and others have been designed to be installed in the next years. Most of the upgrades to the trigger system rely on state-of-the-art technologies, thus allowing to increase the processing power and data transfer bandwidth, and to design more complex trigger menus. As a consequence, more trigger candidates might be selected by the system, thus supporting new physics studies or topological selections. In this work, we discuss the design of the first prototype of the new Barrel Interface Board, designed around a Xilinx FPGA, which will be used to transfer RPC trigger data to the CTP system. The main requirement for the board is to support the optical transmission of the trigger data with fixed latency and to allow the implementation of new trigger algorithms. We describe the hardware implementation and the results of the first functional and integration tests.

physics.ins-det↗