arXiv subjects

Valery V. Frolov

Publications and source records attributed to Valery V. Frolov.

4 recordsLinked to original sources

arXiv2026

Observing and evading quantum back-action on a kilogram-scale oscillator

Continuous quantum displacement measurements are fundamentally limited by a trade-off between readout imprecision and measurement back-action, constrained by the Heisenberg uncertainty principle. In the Laser Interferometric Gravitational-Wave Observatory (LIGO), these two quantum noise components dominate much of the observation band, making it an excellent testbed. We induce a sub-Hz-linewidth optomechanical mode by trapping the differential motion of the 40-kg mirrors in a band where radiation-pressure back-action dominates the motion. Engineering the quantum state entering the dark port creates correlations between imprecision and back-action that partially cancel their contributions, reducing observed motion near resonance by ~47%. A framework resolving the imprecision, back-action, and correlation terms identifies the origin of this suppression. These results demonstrate quantum back-action evasion and quantum reservoir engineering in a macroscopic optomechanical system.

quant-ph↗

arXiv2021

Point absorbers in Advanced LIGO

Small, highly absorbing points are randomly present on the surfaces of the main interferometer optics in Advanced LIGO. The resulting nano-meter scale thermo-elastic deformations and substrate lenses from these micron-scale absorbers significantly reduces the sensitivity of the interferometer directly though a reduction in the power-recycling gain and indirect interactions with the feedback control system. We review the expected surface deformation from point absorbers and provide a pedagogical description of the impact on power build-up in second generation gravitational wave detectors (dual-recycled Fabry-Perot Michelson interferometers). This analysis predicts that the power-dependent reduction in interferometer performance will significantly degrade maximum stored power by up to 50% and hence, limit GW sensitivity, but suggests system wide corrections that can be implemented in current and future GW detectors. This is particularly pressing given that future GW detectors call for an order of magnitude more stored power than currently used in Advanced LIGO in Observing Run 3. We briefly review strategies to mitigate the effects of point absorbers in current and future GW wave detectors to maximize the success of these enterprises.

physics.ins-det↗

arXiv2015

In-situ characterization of the thermal state of resonant optical interferometers via tracking of their higher-order mode resonances

Thermal lensing in resonant optical interferometers such as those used for gravitational wave detection is a concern due to the negative impact on control signals and instrument sensitivity. In this paper we describe a method for monitoring the thermal state of such interferometers by probing the higher-order spatial mode resonances of the cavities within them. We demonstrate the use of this technique to measure changes in the Advanced LIGO input mode cleaner cavity geometry as a function of input power, and subsequently infer the optical absorption at the mirror surfaces at the level of 1 ppm per mirror. We also demonstrate the generation of a useful error signal for thermal state of the Advanced LIGO power recycling cavity by continuously tracking the first order spatial mode resonance frequency. Such an error signal could be used as an input to thermal compensation systems to maintain the interferometer cavity geometries in the presence of transients in circulating light power levels, thereby maintaining optimal sensitivity and maximizing the duty-cycle of the detectors.

gr-qc↗

arXiv2012

DC readout experiment in Enhanced LIGO

The two 4 km long gravitational wave detectors operated by the Laser Interferometer Gravitational-wave Observatory (LIGO) were modified in 2008 to read out the gravitational wave channel using the DC readout form of homodyne detection and to include an optical filter cavity at the output of the detector. As part of the upgrade to Enhanced LIGO, these modifications replaced the radio-frequency (RF) heterodyne system used previously. We describe the motivations for and the implementation of DC readout and the output mode cleaner in Enhanced LIGO. We present characterizations of the system, including measurements and models of the couplings of the noises from the laser source to the gravitational wave readout channel. We show that noise couplings using DC readout are improved over those for RF readout, and we find that the achieved shot-noise-limited sensitivity is consistent with modeled results.

physics.ins-det↗