arXiv subjects

William D. Oliver

Publications and source records attributed to William D. Oliver.

At least 109 records · Page 6Linked to original sources

arXiv2018

A tunable coupling scheme for implementing high-fidelity two-qubit gates

The prospect of computational hardware with quantum advantage relies critically on the quality of quantum gate operations. Imperfect two-qubit gates is a major bottleneck for achieving scalable quantum information processors. Here, we propose a generalizable and extensible scheme for a two-qubit coupler switch that controls the qubit-qubit coupling by modulating the coupler frequency. Two-qubit gate operations can be implemented by operating the coupler in the dispersive regime, which is non-invasive to the qubit states. We investigate the performance of the scheme by simulating a universal two-qubit gate on a superconducting quantum circuit, and find that errors from known parasitic effects are strongly suppressed. The scheme is compatible with existing high-coherence hardware, thereby promising a higher gate fidelity with current technologies.

quant-ph↗

arXiv2018

Distinguishing coherent and thermal photon noise in a circuit QED system

In the cavity-QED architecture, photon number fluctuations from residual cavity photons cause qubit dephasing due to the AC Stark effect. These unwanted photons originate from a variety of sources, such as thermal radiation, leftover measurement photons, and crosstalk. Using a capacitively-shunted flux qubit coupled to a transmission line cavity, we demonstrate a method that identifies and distinguishes coherent and thermal photons based on noise-spectral reconstruction from time-domain spin-locking relaxometry. Using these measurements, we attribute the limiting dephasing source in our system to thermal photons, rather than coherent photons. By improving the cryogenic attenuation on lines leading to the cavity, we successfully suppress residual thermal photons and achieve $T_1$-limited spin-echo decay time. The spin-locking noise spectroscopy technique can readily be applied to other qubit modalities for identifying general asymmetric non-classical noise spectra.

quant-ph↗

arXiv2017

Analysis and mitigation of interface losses in trenched superconducting coplanar waveguide resonators

Improving the performance of superconducting qubits and resonators generally results from a combination of materials and fabrication process improvements and design modifications that reduce device sensitivity to residual losses. One instance of this approach is to use trenching into the device substrate in combination with superconductors and dielectrics with low intrinsic losses to improve quality factors and coherence times. Here we demonstrate titanium nitride coplanar waveguide resonators with mean quality factors exceeding two million and controlled trenching reaching 2.2 $μ$m into the silicon substrate. Additionally, we measure sets of resonators with a range of sizes and trench depths and compare these results with finite-element simulations to demonstrate quantitative agreement with a model of interface dielectric loss. We then apply this analysis to determine the extent to which trenching can improve resonator performance.

quant-ph↗

arXiv2017

Coherent coupled qubits for quantum annealing

Quantum annealing is an optimization technique which potentially leverages quantum tunneling to enhance computational performance. Existing quantum annealers use superconducting flux qubits with short coherence times, limited primarily by the use of large persistent currents $I_\mathrm{p}$. Here, we examine an alternative approach, using qubits with smaller $I_\mathrm{p}$ and longer coherence times. We demonstrate tunable coupling, a basic building block for quantum annealing, between two flux qubits with small ($\sim 50~\mathrm{nA}$) persistent currents. Furthermore, we characterize qubit coherence as a function of coupler setting and investigate the effect of flux noise in the coupler loop on qubit coherence. Our results provide insight into the available design space for next-generation quantum annealers with improved coherence.

quant-ph↗

arXiv2016

Suppressing relaxation in superconducting qubits by quasiparticle pumping

Dynamical error suppression techniques are commonly used to improve coherence in quantum systems. They reduce dephasing errors by applying control pulses designed to reverse erroneous coherent evolution driven by environmental noise. However, such methods cannot correct for irreversible processes such as energy relaxation. In this work, we investigate a complementary, stochastic approach to reducing errors: instead of deterministically reversing the unwanted qubit evolution, we use control pulses to shape the noise environment dynamically. In the context of superconducting qubits, we implement a pumping sequence to reduce the number of unpaired electrons (quasiparticles) in close proximity to the device. We report a 70% reduction in the quasiparticle density, resulting in a threefold enhancement in qubit relaxation times, and a comparable reduction in coherence variability.

quant-ph↗

arXiv2016

Improved superconducting qubit coherence with high-temperature substrate annealing

We assess independently the impact of high-temperature substrate annealing and metal deposition conditions on the coherence of transmon qubits in the standard 2D circuit-QED architecture. We restrict our study to devices made with aluminum interdigital capacitors on sapphire substrates. We record more than an order-of-magnitude improvement in the relaxation time of devices made with an annealed substrate, independent of whether a conventional evaporator or molecular beam epitaxy chamber was used to deposit the aluminum. We also infer similar levels of flux noise and photon shot noise through dephasing measurements on these devices. Our results indicate that substrate annealing plays a primary role in fabricating low-loss qubits, consistent with the hypothesis that substrate-air and substrate-metal interfaces are essential factors limiting the qubit lifetimes in superconducting circuits.

cond-mat.mes-hall↗

arXiv2016

Single microwave-photon detector using an artificial $Λ$-type three-level system

Single photon detection is a requisite technique in quantum-optics experiments in both the optical and the microwave domains. However, the energy of microwave quanta are four to five orders of magnitude less than their optical counterpart, making the efficient detection of single microwave photons extremely challenging. Here, we demonstrate the detection of a single microwave photon propagating through a waveguide. The detector is implemented with an "impedance-matched" artificial $Λ$ system comprising the dressed states of a driven superconducting qubit coupled to a microwave resonator. We attain a single-photon detection efficiency of $0.66 \pm 0.06$ with a reset time of $\sim 400$~ns. This detector can be exploited for various applications in quantum sensing, quantum communication and quantum information processing.

quant-ph↗

arXiv2015

Heisenberg-limited qubit readout with two-mode squeezed light

We show how to use two-mode squeezed light to exponentially enhance cavity-based dispersive qubit measurement. Our scheme enables true Heisenberg-limited scaling of the measurement, and crucially, is not restricted to small dispersive couplings or unrealistically long measurement times. It involves coupling a qubit dispersively to two cavities, and making use of a symmetry in the dynamics of joint cavity quadratures (a so-called quantum-mechanics-free subsystem). We discuss the basic scaling of the scheme and its robustness against imperfections, as well as a realistic implementation in circuit quantum electrodynamics.

quant-ph↗

arXiv2014

Fabrication Process and Properties of Fully-Planarized Deep-Submicron Nb/Al-AlOx/Nb Josephson Junctions for VLSI Circuits

A fabrication process for Nb/Al-AlOx/Nb Josephson junctions (JJs) with sizes down to 200 nm has been developed on a 200-mm-wafer tool set typical for CMOS foundry. This process is the core of several nodes of a roadmap for fully-planarized fabrication processes for superconductor integrated circuits with 4, 8, and 10 niobium layers developed at MIT Lincoln Laboratory. The process utilizes 248 nm photolithography, anodization, high-density plasma etching, and chemical mechanical polishing (CMP) for planarization of SiO$_2$ interlayer dielectric. JJ electric properties and statistics such as on-chip and wafer spreads of critical current, $I_c$, normal-state conductance, $G_N$, and run-to-run reproducibility have been measured on 200-mm wafers over a broad range of JJ diameters from 200 nm to 1500 nm and critical current densities, $J_c$, from 10 kA/$cm^2$ to 50 kA/$cm^2$ where the JJs become self-shunted. Diffraction-limited photolithography of JJs is discussed. A relationship between JJ mask size, JJ size on wafer, and the minimum printable size for coherent and partially coherent illumination has been worked out. The $G_N$ and $I_c$ spreads obtained have been found to be mainly caused by variations of the JJ areas and agree with the model accounting for an enhancement of mask errors near the diffraction-limited minimum printable size of JJs. $I_c$ and $G_N$ spreads from 0.8% to 3% have been obtained for JJs with sizes from 1500 nm down to 500 nm. The spreads increase to about 8% for 200-nm JJs. Prospects for circuit densities > $10^6$ JJ/$cm^2$ and 193-nm photolithography for JJ definition are discussed.

cond-mat.supr-con↗

arXiv2014

Coherence and Decay of Higher Energy Levels of a Superconducting Transmon Qubit

We present measurements of coherence and successive decay dynamics of higher energy levels of a superconducting transmon qubit. By applying consecutive $π$-pulses for each sequential transition frequency, we excite the qubit from the ground state up to its fourth excited level and characterize the decay and coherence of each state. We find the decay to proceed mainly sequentially, with relaxation times in excess of 20 $μ$s for all transitions. We also provide a direct measurement of the charge dispersion of these levels by analyzing beating patterns in Ramsey fringes. The results demonstrate the feasibility of using higher levels in transmon qubits for encoding quantum information.

quant-ph↗

arXiv2014

Flux qubit noise spectroscopy using Rabi oscillations under strong driving conditions

We infer the high-frequency flux noise spectrum in a superconducting flux qubit by studying the decay of Rabi oscillations under strong driving conditions. The large anharmonicity of the qubit and its strong inductive coupling to a microwave line enabled high-amplitude driving without causing significant additional decoherence. Rabi frequencies up to 1.7 GHz were achieved, approaching the qubit's level splitting of 4.8 GHz, a regime where the rotating-wave approximation breaks down as a model for the driven dynamics. The spectral density of flux noise observed in the wide frequency range decreases with increasing frequency up to 300 MHz, where the spectral density is not very far from the extrapolation of the 1/f spectrum obtained from the free-induction-decay measurements. We discuss a possible origin of the flux noise due to surface electron spins.

cond-mat.supr-con↗

arXiv2013

Investigation of nonlinear effects in Josephson parametric oscillators used in circuit QED

We experimentally study the behavior of a parametrically pumped nonlinear oscillator, which is based on a superconducting λ/4 resonator, and is terminated by a flux-tunable SQUID. We extract parameters for two devices. In particular, we study the effect of the nonlinearities in the system and compare to theory. The Duffing nonlinearity, α, is determined from the probe-power dependent frequency shift of the oscillator, and the nonlinearity, β, related to the parametric flux pumping, is determined from the pump amplitude for the onset of parametric oscillations. Both nonlinearities depend on the parameters of the device and can be tuned in-situ by the applied dc flux. We also suggest how to cancel the effect of βby adding a small dc flux and a pump tone at twice the pump frequency.

quant-ph↗

arXiv2012

Improving quantum gate fidelities by using a qubit to measure microwave pulse distortions

We present a new method for determining pulse imperfections and improving the single-gate fidelity in a superconducting qubit. By applying consecutive positive and negative $π$ pulses, we amplify the qubit evolution due to microwave pulse distortion, which causes the qubit state to rotate around an axis perpendicular to the intended rotation axis. Measuring these rotations as a function of pulse period allows us to reconstruct the shape of the microwave pulse arriving at the sample. Using the extracted response to predistort the input signal, we are able to improve the pulse shapes and to reach an average single-qubit gate fidelity higher than 99.8%.

quant-ph↗

arXiv2012

Spectroscopy of low-frequency noise and its temperature dependence in a superconducting qubit

We report a direct measurement of the low-frequency noise spectrum in a superconducting flux qubit. Our method uses the noise sensitivity of a free-induction Ramsey interference experiment, comprising free evolution in the presence of noise for a fixed period of time followed by single-shot qubit-state measurement. Repeating this procedure enables Fourier-transform noise spectroscopy with access to frequencies up to the achievable repetition rate, a regime relevant to dephasing in ensemble-averaged time-domain measurements such as Ramsey interferometry. Rotating the qubit's quantization axis allows us to measure two types of noise: effective flux noise and effective critical-current or charge noise. For both noise sources, we observe that the very same 1/f-type power laws measured at considerably higher frequencies (0.2-20 MHz) are consistent with the noise in the 0.01-100-Hz range measured here. We find no evidence of temperature dependence of the noises over 65-200 mK, and also no evidence of time-domain correlations between the two noises. These methods and results are pertinent to the dephasing of all superconducting qubits.

cond-mat.supr-con↗

arXiv2012

Dynamical decoupling and dephasing in interacting two-level systems

We implement dynamical decoupling techniques to mitigate noise and enhance the lifetime of an entangled state that is formed in a superconducting flux qubit coupled to a microscopic two-level system. By rapidly changing the qubit's transition frequency relative to the two-level system, we realize a refocusing pulse that reduces dephasing due to fluctuations in the transition frequencies, thereby improving the coherence time of the entangled state. The coupling coherence is further enhanced when applying multiple refocusing pulses, in agreement with our $1/f$ noise model. The results are applicable to any two-qubit system with transverse coupling, and they highlight the potential of decoupling techniques for improving two-qubit gate fidelities, an essential prerequisite for implementing fault-tolerant quantum computing.

quant-ph↗

arXiv2012

Time-Reversal Symmetry and Universal Conductance Fluctuations in a Driven Two-Level System

In the presence of time-reversal symmetry, quantum interference gives strong corrections to the electric conductivity of disordered systems. The self-interference of an electron wavefunction traveling time-reversed paths leads to effects such as weak localization and universal conductance fluctuations. Here, we investigate the effects of broken time-reversal symmetry in a driven artificial two-level system. Using a superconducting flux qubit, we implement scattering events as multiple Landau-Zener transitions by driving the qubit periodically back and forth through an avoided crossing. Interference between different qubit trajectories give rise to a speckle pattern in the qubit transition rate, similar to the interference patterns created when coherent light is scattered off a disordered potential. Since the scattering events are imposed by the driving protocol, we can control the time-reversal symmetry of the system by making the drive waveform symmetric or asymmetric in time. We find that the fluctuations of the transition rate exhibit a sharp peak when the drive is time-symmetric, similar to universal conductance fluctuations in electronic transport through mesoscopic systems.

cond-mat.mes-hall↗

arXiv2012

Shadow evaporation of epitaxial Al/Al2O3/Al tunnel junctions on sapphire utilizing an inorganic bilayer mask

This letter describes a new inorganic shadow mask that has been employed for the evaporation of all-epitaxial Al/Al2O3/Al superconducting tunnel junctions. Organic resists that are commonly used for shadow masks and other lift-off processes are not compatible with ultra-high vacuum deposition systems, and they can break down at even moderately elevated temperatures. The inorganic mask described herein does not suffer these same shortcomings. It was fabricated from a Ge/Nb bilayer, comprising suspended Nb bridges supported by an undercut Ge sacrificial layer. Utilizing such a bilayer mask on C-plane sapphire, the growth of epitaxial Al tunnel junctions was achieved using molecular beam epitaxy. Crystalline Al2O3 was grown diffusively at 300 C in a molecular oxygen background of 2.0 utorr, while amorphous oxide was grown at room temperature and 25 mtorr. A variety of analysis techniques were employed to evaluate the materials, and tunnel junction current-voltage characteristics were measured at millikelvin temperatures.

cond-mat.supr-con↗

arXiv2012

Driven dynamics and rotary echo of a qubit tunably coupled to a harmonic oscillator

We have investigated the driven dynamics of a superconducting flux qubit that is tunably coupled to a microwave resonator. We find that the qubit experiences an oscillating field mediated by off-resonant driving of the resonator, leading to strong modifications of the qubit Rabi frequency. This opens an additional noise channel, and we find that low-frequency noise in the coupling parameter causes a reduction of the coherence time during driven evolution. The noise can be mitigated with the rotary-echo pulse sequence, which, for driven systems, is analogous to the Hahn-echo sequence.

cond-mat.supr-con↗