arXiv subjects

Wolfgang Windl

Publications and source records attributed to Wolfgang Windl.

At least 19 recordsLinked to original sources

arXiv2026

Phase-Field Simulation of Dendrite Evolution in All-Solid-State Sodium Batteries during Cycling

Dendrite growth during cycling remains a critical challenge for all-solid-state batteries (SSBs), limiting the full realization of their inherent safety and high energy density. In particular, the mechanisms of continuous dendrite penetration during charge-discharge cycling remain poorly understood and are difficult to characterize experimentally. This study applies a phase-field model, informed by density functional theory calculations, to rationalize and visualize the dendrite penetration behaviors during cycling in sodium (Na) SSBs with pure Na or Na-Sb alloy anodes and polycrystalline Na$_3$SbS$_4$ electrolyte. We show that dendrite stripping is intrinsically asymmetric with respect to plating due to grain boundary geometry, leading to the formation of isolated Na metal that persists between cycles. This residual Na metal becomes kinetically stabilized at grain-boundary junctions and is readily reactivated during subsequent plating, thereby accelerating and amplifying dendrite penetration. We further investigate the effects of applied voltage, solid-electrolyte microstructure, and anode chemistry on this phenomenon. These findings establish isolated Na metal as a key contributor for continued dendrite propagation in Na SSBs and provide design principles for stabilizing anode/electrolyte interfaces in Na SSBs.

cond-mat.mtrl-sci↗

arXiv2026

Frontiers of atom probe tomography physics, data processing, and analysis

Atom probe tomography (APT) fills a crucial need in the characterization workflow of materials by its ability to inform the 3D chemical microstructure at the nanoscale. As with any characterization techniques, APT has strengths and limitations that inform the interpretation of the data. Therefore, a challenge for the materials characterization community, and the APT community in particular, is the need to establish repeatable and reproducible workflows around the APT data acquisition, reconstruction, analysis, and sharing, in order to inform interpretation. Data interpretation also requires the continued development of our understanding of the physical processes responsible for field evaporation. We review recent developments in the experimental analysis of field evaporation and in the modeling of field evaporation leading to new understanding of common artifacts observed in reconstructed data. We then discuss current challenges with data analysis, translation of results, and data interpretation in the absence of community-agreed standards, and therefore, the crucial need for standardization at every stage of APT research, from data collection all the way to data reporting. This perspective is a summary of the invited presentations and discussions that took place during a workshop (August 4-5, 2024, Alexandria, Virginia, USA).

cond-mat.mtrl-sci↗

arXiv2024

New three-dimensional dispersion in the type-II Dirac semimetals PtTe$_2$ and PdTe$_2$ revealed through Angle Resolved Photoemission Spectroscopy

PtTe$_2$ and PdTe$_2$ are among the first transition metal dichalcogenides that were predicted to host type-II Dirac fermions, exotic particles prohibited in free space. These materials are layered and air-stable, which makes them top candidates for technological applications that take advantage of their anisotropic magnetotransport properties. Here, we provide a detailed characterization of the electronic structure of PtTe$_2$ and PdTe$_2$ using Angle Resolved Photoemission Spectroscopy (ARPES) and Density Functional Theory (DFT) calculations, unveiling a new three-dimensional dispersion in these materials. Through the use of circularly polarized light, we report a different behavior of such dispersion in PdTe$_2$ compared to PtTe$_2$, that we relate to a symmetry analysis of the dipole matrix element. Such analysis reveals a link between the observed circular dichroism and the different momentum-dependent terms in the dispersion of these two compounds, despite their close similarity in crystal structure. Additionally, our data shows a clear difference in the circular dichroic signal for the type-II Dirac cones characteristic of these materials, compared to their topologically protected surface states. Our work provides a useful reference for the ARPES characterization of other transition metal dichalcogenides with topological properties and illustrates the use of circular dichroism as a guide to identify the topological character of two otherwise equivalent band dispersions, and to recognize different attributes in the band structure of similar materials.

cond-mat.mes-hall↗

arXiv2023

Unexpected Field Evaporation Sequence in $γ$-TiAl

In atom probe tomography (APT), atoms from the surface of a needle shape specimen are evaporated under a high electric field and analyzed via time of flight mass spectrometry and position sensitive detection. 3D reconstruction of the atom positions follows a simple projection law, which can sometimes lead to artifacts due to deviation from an assumed ideal evaporation sequence. Here, we revisit the evaporation behavior of [001]-oriented $γ$-TiAl using a full-dynamics simulation approach empowered by molecular dynamics. Without any knowledge of charge states or assumptions about evaporation fields, we successfully reproduced the lack of distinct Al and Ti layers observed in reconstructions of experimental data which is traditionally attributed to the retention of Al on the evaporating surface. We further showed that a step-wise bond breaking process of Ti in contrast to the simultaneous bond breaking of Al explains the seemingly counterintuitive preferential evaporation of the strongly bonded Ti atoms.

cond-mat.mtrl-sci↗

arXiv2022

Ab-Initio Simulation of Field Evaporation

A new simulation approach of field evaporation is presented. The model combines classical electrostatics with molecular dynamics (MD) simulations. Unlike previous atomic-level simulation approaches, our method does not rely on an evaporation criterion based on thermal activation theory, instead, electric-field-induced forces on atoms are explicitly calculated and added to the interatomic forces. Atoms then simply move according to the laws of classical molecular dynamics and are "evaporated" when the external force overcomes interatomic bonding. This approach thus makes no ad-hoc assumptions concerning evaporation fields and criteria, which makes the simulation fully physics-based and "ab-initio" apart from the interatomic potential. As proof of principle, we perform simulations to determine material dependent critical voltages which allow assessing the evaporation fields and the corresponding steady-state tip shapes in different metals. We also extract critical evaporation fields in elemental metals and sublimation energies in a high entropy alloy to have a more direct comparison with tabulated values. In contrast to previous approaches, we show that our method is able to successfully reproduce the enhanced zone lines observed in experimental field desorption patterns. We also demonstrate the need for careful selection of the interatomic potential by a comparative study for the example of Cu-Ni alloys.

cond-mat.mtrl-sci↗

arXiv2022

Origin of Enhanced Zone Lines in Field Desorption Maps

Artifacts in the collective desorption map of the detector hits impede a truthful reconstruction, including enhanced "zone lines" with high atomic impact intensity. Since APT is destructive, simulation is the only approach to explain the origin of these zone lines, but previous work couldn't reproduce them. Here, we use a new simulation technique that adds the full electrostatic forces to the interatomic forces in a molecular-dynamics simulation and eliminates the previous ad-hoc assumptions. We find for the canonical example of tungsten that evaporation happens when the electrostatic force overpowers the interatomic force, and the misalignment of the two forces deviates the launch direction of the atoms in certain zones, giving rise to an accumulation of hit events around zone lines.

cond-mat.mtrl-sci↗

arXiv2022

Rapid Production of Accurate Embedded-Atom Method Potentials for Metal Alloys

A critical limitation to the wide-scale use of classical molecular dynamics for alloy design is the limited availability of suitable interatomic potentials. Here, we introduce the Rapid Alloy Method for Producing Accurate General Empirical Potentials or RAMPAGE, a computationally economical procedure to generate binary embedded-atom model potentials from already-existing single-element potentials that can be further combined into multi-component alloy potentials. We present the quality of RAMPAGE calibrated Finnis-Sinclair type EAM potentials using binary Ag-Al and ternary Ag-Au-Cu as case studies. We demonstrate that RAMPAGE potentials can reproduce bulk properties and forces with greater accuracy than that of other alloy potentials. In some simulations, it is observed the quality of the optimized cross interactions can exceed that of the original off-the-shelf elemental potential inputs.

cond-mat.mtrl-sci↗

arXiv2022

Bayesian calibration of interatomic potentials for binary alloys

Developing reliable interatomic potential models with quantified predictive accuracy is crucial for atomistic simulations. Commonly used potentials, such as those constructed through the embedded atom method (EAM), are derived from semi-empirical considerations and contain unknown parameters that must be fitted based on training data. In the present work, we investigate Bayesian calibration as a means of fitting EAM potentials for binary alloys. The Bayesian setting naturally assimilates probabilistic assertions about uncertain quantities. In this way, uncertainties about model parameters and model errors can be updated by conditioning on the training data and then carried through to prediction. We apply these techniques to investigate an EAM potential for a family of gold-copper systems in which the training data correspond to density-functional theory values for lattice parameters, mixing enthalpies, and various elastic constants. Through the use of predictive distributions, we demonstrate the limitations of the potential and highlight the importance of statistical formulations for model error.

cond-mat.mtrl-sci↗

arXiv2021

Non-Linear Arrhenius Behavior of Self-Diffusion in $β$-Ti and Mo

While anomalous diffusion coefficients with non-Arrhenius like temperature dependence are observed in a number of metals, a conclusive comprehensive framework of explanation has not been brought forward to date. Here, we use first-principles calculations based on density functional theory to calculate self-diffusion coefficients in the bcc metals Mo and $β$-Ti by coupling quasiharmonic transition state theory and large displacement phonon calculations and show that anharmonicity from thermal expansion is the major reason for the anomalous temperature dependence. We use a modified Debye approach to quantify the thermal expansion over the entire temperature range and introduce a method to relax the vacancy structure in a mechanically unstable crystal such as $β$-Ti. Thermal expansion is found to weakly affect the activation enthalpy but has a strong effect on the prefactor of the diffusion coefficient, reproducing the non-linear, non-Arrhenius "anomalous" self-diffusion in both bcc systems with good agreement between calculation and experiment. The proposed methodology is general and simple enough to be applicable to other mechanically unstable crystals.

cond-mat.mtrl-sci↗

arXiv2021

Native point defects from stoichiometry-linked chemical potentials in cubic boron arsenide

The presence of a point defect typically breaks the stoichiometry in a semiconductor. For example, a vacancy on an A-site in an AB compound makes the crystal B-rich. As the stoichiometry changes, so do the chemical potentials. While the prevalent first-principles methods have provided significant insight into characters of point defects in a transparent manner, the crucial connection between crystal stoichiometry and chemical potentials is usually not made. However, ad hoc choices for chemical potentials can lead to nonphysical negative formation energies in some Fermi level ranges, along with questions about charge balance. Herein, we formulate a canonical framework describing how the chemical potential of each element is directly linked to the composition of the crystal under (off-)stoichiometric conditions instead of the ad hoc assumption that the chemical potential is the elemental limit under a certain growth condition. Consequently, the chemical potential changes with the Fermi level within the band gap, and the formation energies are positive. Using such an approach, we present $ab$ $initio$ results for native point defects in BAs, a semiconductor with ultra-high room temperature thermal conductivity. We find that antisites are the constitutional defects in off-stoichiometric material, while B$_\mathrm{As}$ antisites and B vacancies dominate in the stoichiometric material. We further discuss the thermodynamic equilibrium and charge neutrality point in BAs in light of our stoichiometry-determined chemical potentials. As discussed, our work offers a more applicable and accessible approach to tackle defect formation energies in semiconductors, especially the ones with wide gap where negative formation energies are commonly seen.

cond-mat.mtrl-sci↗

arXiv2020

Bond Synergy Model for Bond Energies in Alloy Oxides

In this work we introduce a metal-oxide bond-energy model for alloy oxides based on pure-phase bond energies and bond synergy factors that describe the effect of alloying on the bond energy between cations and oxygen, an important quantity to understand formation and stability of passive films. This model is parameterized for binary cation-alloy oxides using density-functional theory energies and is shown to be directly transferable to multi-component alloy oxides. We parameterized the model for alloy oxide energies with metal cations that form the basis of corrosion resistant alloys, including Fe, Ni, Cr, Mo, Mn, W, Co, and Ru. We find that isoelectronic solutes allow quantification of pure-phase bond energies in oxides and that the calculated bond energy values give sensible results compared to common experience, including the role of Cr as the passive-layer former in Fe-Ni-Cr alloys for corrosion applications. Additionally, the bond synergy factors give insights into the mutual strengthening and weakening effects of alloying on cation-oxygen bonds and can be related to enthalpy of mixing and charge neutrality constraints. We demonstrate how charge neutrality can be identified and achieved by the oxidation states that the different cations assume depending on alloy composition and the presence of defects.

cond-mat.mtrl-sci↗

arXiv2019

Ferromagnetic Epitaxial μ-Fe$_{2}$O$_{3}$ on β-Ga$_{2}$O$_{3}$: A New Monoclinic form of Fe$_{2}$O$_{3}$

Here we demonstrate a new monoclinic iron oxide phase (μ-Fe$_{2}$O$_{3}$), epitaxially stabilized by growth on (010) β-Ga$_{2}$O$_{3}$. Density functional theory (DFT) calculations find that the lattice parameters of freestanding μ-Fe$_{2}$O$_{3}$ are within ~1% of those of β-Ga$_{2}$O$_{3}$ and that its energy of formation is comparable to that of naturally abundant Fe$_{2}$O$_{3}$ polytypes. A superlattice of μ-Fe$_{2}$O$_{3}$/β-Ga$_{2}$O$_{3}$ is grown by plasma assisted molecular beam epitaxy, with resulting high-resolution x-ray diffraction (XRD) measurements indicating that the μ-Fe$_{2}$O$_{3}$ layers are lattice-matched to the substrate. The measured out-of-plane (b) lattice parameter of 3.12 $\pm$ 0.4 Å is in agreement with the predicted lattice constants and atomic-resolution scanning transmission electron microscopy (STEM) images confirm complete registry of the μ-Fe$_{2}$O$_{3}$ layers with β-Ga$_{2}$O$_{3}$. Finally, DFT modeling predicts that bulk μ-Fe$_{2}$O$_{3}$ is antiferromagnetic, while the interface region between μ-Fe$_{2}$O$_{3}$ and β-Ga$_{2}$O$_{3}$ leads to ferromagnetic coupling between interface Fe$^{3+}$ cations selectively occupying tetrahedral positions. Magnetic hysteresis persisting to room temperature is observed via SQUID measurements, consistent with the computationally predicted interface magnetism.

cond-mat.mtrl-sci↗

arXiv2018

Multi-Cell Monte Carlo Method for Phase Prediction

We propose a Multi-Cell Monte Carlo algorithm, or (MC)^2, for predicting stable phases in chemically complex crystalline systems. Free atomic transfer among cells is achieved via the application of the lever rule, where an assigned molar ratio virtually controls the percentage of each cell in the overall simulation, making (MC)^2 the first successful algorithm for simulating phase coexistence in crystalline solids. During the application of this method, all energies are computed via direct Density Functional Theory calculations. We test the method by successful prediction of the stable phases of known binary systems. We then apply the method to a quaternary high entropy alloy. The method is particularly robust in predicting stable phases of multi-component systems for which phase diagrams do not exist.

cond-mat.mtrl-sci↗

arXiv2018

Raman Spectroscopy, Photocatalytic Degradation and Stabilization of Atomically Thin Chromium Triiodide

As a 2D ferromagnetic semiconductor with magnetic ordering, atomically thin chromium triiodide is the latest addition to the family of two-dimensional (2D) materials. However, realistic exploration of CrI3-based devices and heterostructures is challenging, due to its extreme instability under ambient conditions. Here we present Raman characterization of CrI3, and demonstrate that the main degradation pathway of CrI3 is the photocatalytic substitution of iodine by water. While simple encapsulation by Al2O3, PMMA and hexagonal BN (hBN) only leads to modest reduction in degradation rate, minimizing exposure of light markedly improves stability, and CrI3 sheets sandwiched between hBN layers are air-stable for >10 days. By monitoring the transfer characteristics of CrI3/graphene heterostructure over the course of degradation, we show that the aquachromium solution hole-dopes graphene.

cond-mat.mes-hall↗

arXiv2017

NaSn2As2: An Exfoliatable Layered van der Waals Zintl Phase

The discovery of new families of exfoliatable 2D crystals that have diverse sets of electronic, optical, and spin-orbit coupling properties, enables the realization of unique physical phenomena in these few-atom thick building blocks and in proximity to other materials. Herein, using NaSn2As2 as a model system, we demonstrate that layered Zintl phases having the stoichiometry ATt2Pn2 (A = Group 1 or 2 element, Tt = Group 14 tetrel element and Pn = Group 15 pnictogen element) and feature networks separated by van der Waals gaps can be readily exfoliated with both mechanical and liquid-phase methods. We identified the symmetries of the Raman active modes of the bulk crystals via polarized Raman spectroscopy. The bulk and mechanically exfoliated NaSn2As2 samples are resistant towards oxidation, with only the top surface oxidizing in ambient conditions over a couple of days, while the liquid-exfoliated samples oxidize much more quickly in ambient conditions. Employing angle-resolved photoemission spectroscopy (ARPES), density functional theory (DFT), and transport on bulk and exfoliated samples, we show that NaSn2As2 is a highly conducting 2D semimetal, with resistivities on the order of 10-6 Ω m. Due to peculiarities in the band structure, the dominating p-type carriers at low temperature are nearly compensated by the opening of n-type conduction channels as temperature increases. This work further expands the family of exfoliatable 2D materials to layered van der Waals Zintl phases, opening up opportunities in electronics and spintronics.

cond-mat.mtrl-sci↗

arXiv2017

Magnetic Proximity Effect in Pt/CoFe2O4 Bilayers

We observe the magnetic proximity effect (MPE) in Pt/CoFe2O4 bilayers grown by molecular beam epitaxy. This is revealed through angle-dependent magnetoresistance measurements at 5 K, which isolate the contributions of induced ferromagnetism (i.e. anisotropic magnetoresistance) and spin Hall effect (i.e. spin Hall magnetoresistance) in the Pt layer. The observation of induced ferromagnetism in Pt via AMR is further supported by density functional theory calculations and various control measurements including insertion of a Cu spacer layer to suppress the induced ferromagnetism. In addition, anomalous Hall effect measurements show an out-of-plane magnetic hysteresis loop of the induced ferromagnetic phase with larger coercivity and larger remanence than the bulk CoFe2O4. By demonstrating MPE in Pt/CoFe2O4, these results establish the spinel ferrite family as a promising material for MPE and spin manipulation via proximity exchange fields.

cond-mat.mtrl-sci↗

arXiv2016

Improved model for the thermal conductivity of binary metallic systems

We extended and corrected Mott's two-band model for the composition-dependence of thermal and electrical conductivity in binary metal alloys based on high-throughput time-domain thermoreflectance (TDTR) measurements on diffusion multiples and scatterer-density calculations from first principles. Examining PdAg, PtRh, AuAg, AuCu, PdCu, PdPt, and NiRh binary alloys, we found that the nature of the two dominant scatterer-bands considered in the Mott model changes with the alloys, and should be interpreted as a combination of the dominant element-specific s- and/or d-orbitals. Using calculated orbital and element-resolved density-of-states values calculated with density functional theory as input, we determined the correct orbital mix that dominates electron scattering for all examined alloys and find excellent agreement between fitted models and experiments. The proposed description of the composition dependence of the resistivity can be readily implemented into the CALPHAD framework.

cond-mat.mtrl-sci↗

arXiv2015

Effects of the local structure dependence of evaporation fields on field evaporation behavior

Accurate three dimensional reconstructions of atomic positions, and full quantification of the information contained in atom probe tomography data relies on understanding the physical processes taking place during field evaporation of atoms from needle-shaped specimens. However, the modeling framework for atom probe tomography has remained qualitative at best. Building on the continuum field models previously developed, we introduce a more physical approach with the selection of evaporation events based on density functional theory calculations. This new model reproduces key features observed experimentally in terms of sequence of evaporation, desorption maps, and depth resolution, and provides insights into the physical limit for spatial resolution.

physics.atom-ph↗