arXiv subjects

Xiaoji Niu

Publications and source records attributed to Xiaoji Niu.

27 records · Page 2Linked to original sources

arXiv2022

Wheel-INS2: Multiple MEMS IMU-based Dead Reckoning System for Wheeled Robots with Evaluation of Different IMU Configurations

A reliable self-contained navigation system is essential for autonomous vehicles. Based on our previous study on Wheel-INS \cite{niu2019}, a wheel-mounted inertial measurement unit (Wheel-IMU)-based dead reckoning (DR) system, in this paper, we propose a multiple IMUs-based DR solution for the wheeled robots. The IMUs are mounted at different places of the wheeled vehicles to acquire various dynamic information. In particular, at least one IMU has to be mounted at the wheel to measure the wheel velocity and take advantages of the rotation modulation. The system is implemented through a distributed extended Kalman filter structure where each subsystem (corresponding to each IMU) retains and updates its own states separately. The relative position constraints between the multiple IMUs are exploited to further limit the error drift and improve the system robustness. Particularly, we present the DR systems using dual Wheel-IMUs, one Wheel-IMU plus one vehicle body-mounted IMU (Body-IMU), and dual Wheel-IMUs plus one Body-IMU as examples for analysis and comparison. Field tests illustrate that the proposed multi-IMU DR system outperforms the single Wheel-INS in terms of both positioning and heading accuracy. By comparing with the centralized filter, the proposed distributed filter shows unimportant accuracy degradation while holds significant computation efficiency. Moreover, among the three multi-IMU configurations, the one Body-IMU plus one Wheel-IMU design obtains the minimum drift rate. The position drift rates of the three configurations are 0.82\% (dual Wheel-IMUs), 0.69\% (one Body-IMU plus one Wheel-IMU), and 0.73\% (dual Wheel-IMUs plus one Body-IMU), respectively.

cs.RO↗

arXiv2022

Exploring the Accuracy Potential of IMU Preintegration in Factor Graph Optimization

Inertial measurement unit (IMU) preintegration is widely used in factor graph optimization (FGO); e.g., in visual-inertial navigation system and global navigation satellite system/inertial navigation system (GNSS/INS) integration. However, most existing IMU preintegration models ignore the Earth's rotation and lack delicate integration processes, and these limitations severely degrade the INS accuracy. In this study, we construct a refined IMU preintegration model that incorporates the Earth's rotation, and analytically compute the covariance and Jacobian matrix. To mitigate the impact caused by sensors other than IMU in the evaluation system, FGO-based GNSS/INS integration is adopted to quantitatively evaluate the accuracy of the refined preintegration. Compared to a classic filtering-based GNSS/INS integration baseline, the employed FGO-based integration using the refined preintegration yields the same accuracy. In contrast, the existing rough preintegration yields significant accuracy degradation. The performance difference between the refined and rough preintegration models can exceed 200% for an industrial-grade MEMS module and 10% for a consumer-grade MEMS chip. Clearly, the Earth's rotation is the major factor to be considered in IMU preintegration in order to maintain the IMU precision, even for a consumer-grade IMU.

cs.RO↗

arXiv2022

IC-GVINS: A Robust, Real-time, INS-Centric GNSS-Visual-Inertial Navigation System for Wheeled Robot

In this letter, we present a robust, real-time, inertial navigation system (INS)-Centric GNSS-Visual-Inertial navigation system (IC-GVINS) for wheeled robot, in which the precise INS is fully utilized in both the state estimation and visual process. To improve the system robustness, the INS information is employed during the whole keyframe-based visual process, with strict outlier-culling strategy. GNSS is adopted to perform an accurate and convenient initialization of the IC-GVINS, and is further employed to achieve absolute positioning in large-scale environments. The IMU, visual, and GNSS measurements are tightly fused within the framework of factor graph optimization. Dedicated experiments were conducted to evaluate the robustness and accuracy of the IC-GVINS on a wheeled robot. The IC-GVINS demonstrates superior robustness in various visual-degenerated scenes with moving objects. Compared to the state-of-the-art visual-inertial navigation systems, the proposed method yields improved robustness and accuracy in various environments. We open source our codes combined with the dataset on GitHub

cs.RO↗

arXiv2021

OdoNet: Untethered Speed Aiding for Vehicle Navigation Without Hardware Wheeled Odometer

Odometer has been proven to significantly improve the accuracy of the Global Navigation Satellite System / Inertial Navigation System (GNSS/INS) integrated vehicle navigation in GNSS-challenged environments. However, the odometer is inaccessible in many applications, especially for aftermarket devices. To apply forward speed aiding without hardware wheeled odometer, we propose OdoNet, an untethered one-dimensional Convolution Neural Network (CNN)-based pseudo-odometer model learning from a single Inertial Measurement Unit (IMU), which can act as an alternative to the wheeled odometer. Dedicated experiments have been conducted to verify the feasibility and robustness of the OdoNet. The results indicate that the IMU individuality, the vehicle loads, and the road conditions have little impact on the robustness and precision of the OdoNet, while the IMU biases and the mounting angles may notably ruin the OdoNet. Thus, a data-cleaning procedure is added to effectively mitigate the impacts of the IMU biases and the mounting angles. Compared to the process using only non-holonomic constraint (NHC), after employing the pseudo-odometer, the positioning error is reduced by around 68%, while the percentage is around 74% for the hardware wheeled odometer. In conclusion, the proposed OdoNet can be employed as an untethered pseudo-odometer for vehicle navigation, which can efficiently improve the accuracy and reliability of the positioning in GNSS-denied environments.

cs.RO↗

arXiv2021

A Comparison of Three Measurement Models for the Wheel-mounted MEMS IMU-based Dead Reckoning System

A self-contained autonomous dead reckoning (DR) system is desired to complement the Global Navigation Satellite System (GNSS) for land vehicles, for which odometer-aided inertial navigation system (ODO/INS) is a classical solution. In this study, we use a wheel-mounted MEMS IMU (Wheel-IMU) to substitute the odometer, and further, investigate three types of measurement models, including the velocity measurement, displacement increment measurement, and contact point zero-velocity measurement, in the Wheel-IMU based DR system. The measurement produced by the Wheel-IMU along with the non-holonomic constraint (NHC) are fused with INS through an error-state extended Kalman filter (EKF). Theoretical discussion and field tests illustrate the feasibility and equivalence of the three measurements in terms of the overall DR performance. The maximum horizontal position drifts are all less than 2% of the total travelled distance. Additionally, the displacement increment measurement model is less sensitive to the lever arm error between the Wheel-IMU and the wheel center.

cs.RO↗

arXiv2021

Wheel-INS: A Wheel-mounted MEMS IMU-based Dead Reckoning System

To improve the accuracy and robustness of the inertial navigation systems (INS) for wheeled robots without adding additional component cost, we propose Wheel-INS, a complete dead reckoning solution based on a wheel-mounted microelectromechanical system (MEMS) inertial measurement unit (IMU). There are two major advantages by mounting an IMU to the center of a non-steering wheel of the ground vehicle. Firstly, the gyroscope outputs can be used to calculate the wheel speed, so as to replace the traditional odometer to mitigate the error drift of INS. Secondly, with the rotation of the wheel, the constant bias error of the inertial sensor can be canceled to some extent. The installation scheme of the wheel-mounted IMU (Wheel-IMU), the system characteristics, and the dead reckoning error analysis are described. Experimental results show that the maximum position drift of Wheel-INS in the horizontal plane is less than 1.8% of the total traveled distance, reduced by 23% compared to the conventional odometer-aided INS (ODO/INS). In addition, Wheel-INS outperforms ODO/INS because of its inherent immunity to constant bias error of gyroscopes. The source code and experimental datasets used in this paper is made available to the community (https://github.com/i2Nav-WHU/Wheel-INS).

cs.RO↗

arXiv2020

Inertial Sensing Meets Artificial Intelligence: Opportunity or Challenge?

The inertial navigation system (INS) has been widely used to provide self-contained and continuous motion estimation in intelligent transportation systems. Recently, the emergence of chip-level inertial sensors has expanded the relevant applications from positioning, navigation, and mobile mapping to location-based services, unmanned systems, and transportation big data. Meanwhile, benefit from the emergence of big data and the improvement of algorithms and computing power, artificial intelligence (AI) has become a consensus tool that has been successfully applied in various fields. This article reviews the research on using AI technology to enhance inertial sensing from various aspects, including sensor design and selection, calibration and error modeling, navigation and motion-sensing algorithms, multi-sensor information fusion, system evaluation, and practical application. Based on the over 30 representative articles selected from the nearly 300 related publications, this article summarizes the state of the art, advantages, and challenges on each aspect. Finally, it summarizes nine advantages and nine challenges of AI-enhanced inertial sensing and then points out future research directions.

eess.SP↗

arXiv2020

Autonomous Calibration of MEMS Gyros in Consumer Portable Devices

This paper presents a real-time calibration method for gyro sensors in consumer portable devices. The calibration happens automatically without the need for external equipment or user intervention. Multi-level constraints, including the pseudo-observations, the accelerometer and magnetometer measurements, and the quasi-static attitude updates, are used to make the method reliable and accurate under natural user motions. Walking tests with the Samsung Galaxy S3 and S4 smartphones showed that the method estimate promising calibration results even under challenging motion modes such as dangling and pocket, and in challenging indoor environments with frequent magnetic interferences.

eess.SP↗

arXiv2020

Location-Enabled IoT (LE-IoT): A Survey of Positioning Techniques, Error Sources, and Mitigation

The Internet of Things (IoT) has started to empower the future of many industrial and mass-market applications. Localization techniques are becoming key to add location context to IoT data without human perception and intervention. Meanwhile, the newly-emerged Low-Power Wide-Area Network (LPWAN) technologies have advantages such as long-range, low power consumption, low cost, massive connections, and the capability for communication in both indoor and outdoor areas. These features make LPWAN signals strong candidates for mass-market localization applications. However, there are various error sources that have limited localization performance by using such IoT signals. This paper reviews the IoT localization system through the following sequence: IoT localization system review -- localization data sources -- localization algorithms -- localization error sources and mitigation -- localization performance evaluation. Compared to the related surveys, this paper has a more comprehensive and state-of-the-art review on IoT localization methods, an original review on IoT localization error sources and mitigation, an original review on IoT localization performance evaluation, and a more comprehensive review of IoT localization applications, opportunities, and challenges. Thus, this survey provides comprehensive guidance for peers who are interested in enabling localization ability in the existing IoT systems, using IoT systems for localization, or integrating IoT signals with the existing localization sensors.

cs.NI↗