arXiv subjects

Xuehua Zhang

Publications and source records attributed to Xuehua Zhang.

At least 37 records · Page 2Linked to original sources

arXiv2022

Flow induced dissolution of femtoliter surface droplet arrays

The dissolution of liquid nanodroplets is a crucial step in many applied processes, such as separation and dispersion in food industry, crystal formation of pharmaceutical products, concentrating and analysis in medical diagnosis, and drug delivery in aerosols. In this work, using both experiments and numerical simulations, we \textit{quantitatively} study the dissolution dynamics of femtoliter surface droplets in a highly ordered array under a uniform flow. Our results show that the dissolution of femoliter droplets strongly depends on their spatial positions relative to the flow direction, drop-to-drop spacing in the array, and the imposed flow rate. In some particular case, the droplet at the edge of the array can dissolve about 30% faster than the ones located near the centre. The dissolution rate of the droplet increases by 60% as the inter-droplet spacing is increased from 2.5 $μ$m to 20 $μ$m. Moreover, the droplets close to the front of flow commence to shrink earlier than those droplets in the center of the array. The average dissolution rate is faster for faster flow. As a result, the dissolution time $T_{i}$ decreases with the Reynolds number Re of the flow as $T_{i}\propto Re^{-3/4}$. The experimental results are in good agreement with numerical simulations where the advection-diffusion equation for the concentration field is solved and the concentration gradient on the surface of the drop is computed. The findings suggest potential approaches to manipulate nanodroplet sizes in droplet arrays simply by dissolution controlled by an external flow. The obtained droplets with varying curvatures may serve as templates for generating multifocal microlens in one array.

cond-mat.soft↗

arXiv2022

Asphaltene precipitation under controlled mixing conditions in a microchamber

Solvent exchange is a controlled process for dilution-induced phase separation. This work utilizes the solvent exchange method to reveal the effect of the mixing dynamics on the asphaltene precipitation process under 20 different mixing conditions using a model system of n-heptane and asphaltene in toluene. The external mixing between the asphaltene solution and the paraffinic solvent is strictly controlled. We employed a high-spatial-resolution total internal reflection fluorescence microscope to detect asphaltene precipitates with a resolution up to 200 nm. A multiphysics model is used to simulate the evolution of the oversaturation pulse in the solvent exchange process. Based on the simulation results, we predicted the effect of the flow rate, dimension, the orientation of the microfluidic chamber, and temperature on the surface coverage and size distribution of asphaltene precipitates. The model predictions of all factors corroborate with the experimental observations. Local concentration of the solvent and shear forces are found to be the two main reasons for the change of asphaltene precipitation caused by mixing dynamics. However, the influence of thermodynamics is more critical than the mixing dynamics as temperature changes. Through a combination of experimental and simulation studies, this work illuminates the significance of the transportation process for the final morphology of asphaltene precipitates and provides an in-depth insight into the mechanism of mixing dynamics on the asphaltene precipitation. A smart mixing may be to boost new phase formation without excessive solvent consumption.

physics.flu-dyn↗

arXiv2022

Computational fluid dynamics (CFD) simulation of three-phase non-Newtonian slurry flows in industrial horizontal pipelines

Understanding the flow behavior of complex concentrated slurries is of tremendous importance for industrial waste management. In this study, the transport of three-phase oil sands tailings in a horizontal pipeline is simulated via the mixture multiphase model coupled with the kinetic theory of granular flow. The solid particles and bitumen droplets are conveyed via a non-Newtonian carrier fluid in a turbulent regime inside an industrial-scale pipeline. The simulation results showed exceptional agreement with the field data, with errors of <3.5% for velocity distribution and <15% for the pressure drop. A systematic parametric investigation was performed for a wide range of flow conditions, showing that the majority of bitumen droplets reside at the top region of the pipe. Our findings may help design an effective process for the separation of bitumen residues during pipeline transport.

physics.flu-dyn↗

arXiv2022

Size distribution of primary submicron particles and larger aggregates in solvent induced asphaltene precipitation

Asphaltene precipitation is a crucial phase separation phenomenon in the oil industry, especially in paraffinic froth treatment to extract bitumen from oil sands ores. This work reveals the formation of particles at 0.2 to 0.4 um in radius, defined as a primary sub-micron particle (PSMP), which is ubiquitous from diffusive mixing between asphaltene solution and any of 23 types of precipitants examined in our experiments. The yield and quantity of asphaltene particles are affected not only by the Hildebrand solubility parameter of the precipitants but also by the diffusion coefficients of the asphaltene solution and the precipitant. The Population Balance Model (PBM) with the Hildebrand solubility parameter has been used to model particle size distribution. Good agreement has been achieved between numerical predictions and the experimental data. It indicates that the colloid theory can describe the size distribution of PSMP and larger aggregates. Therefore, this study provides new insight into the mechanism for the dependence of yield and size distribution of the precipitated asphaltene particles on the composition of precipitants and adding inhibitors. Controlling of asphaltene yield and size distribution may be applied to the process of hydrocarbon separation or asphaltene precipitation prevention.

cond-mat.soft↗

arXiv2022

Surface microlenses for much more efficient photodegradation in water treatment

The global need for clean water requires sustainable technology for purifying contaminated water. Highly efficient solar-driven photodegradation is a sustainable strategy for wastewater treatment. In this work, we demonstrate that the photodegradation efficiency of micropollutants in water can be improved by ~2-24 times by leveraging polymeric microlenses (MLs). These microlenses (MLs) are fabricated from the in-situ polymerization of surface nanodroplets. We found that photodegradation efficiency (η) in water correlates approximately linearly with the sum of the intensity from all focal points of MLs, although no difference in the photodegradation pathway is detected from the chemical analysis of the byproducts. With the same overall power over a given surface area, η is doubled by using ordered arrays, compared to heterogeneous MLs on an unpatterned substrate. Higher η from ML arrays may be attributed to a coupled effect from the focal points on the same plane that creates high local concentrations of active species to further speed up the rate of photodegradation. As a proof-of-concept for ML-enhanced water treatment, MLs were formed on the inner wall of glass bottles that were used as containers for water to be treated. Three representative micropollutants (norfloxacin, sulfadiazine, and sulfamethoxazole) in the bottles functionalized by MLs were photodegraded by 30% to 170% faster than in normal bottles. Our findings suggest that the ML-enhanced photodegradation may lead to a highly efficient solar water purification approach without a large solar collector size. Such an approach may be particularly suitable for portable transparent bottles in remote regions.

physics.chem-ph↗

arXiv2022

Growth Rates of Hydrogen Microbubbles in Reacting Femtoliter Droplets

Chemical reactions in small droplets are extensively explored to accelerate the discovery of new materials, increase efficiency and specificity in catalytic biphasic conversion and in high throughput analytics. In this work, we investigate the local rate of gas-evolution reaction within femtoliter droplets immobilized on a solid surface. The growth rate of hydrogen microbubbles (> 500 nm in radius) produced from the reaction was measured online by high-resolution confocal microscopic images. The growth rate of bubbles was faster in smaller droplets, and of bubbles near the three-phase boundary in the same droplet. The results were consistent for both pure and binary reacting droplets and on substrates of different wettability. Our theoretical analysis based on diffusion, chemical reaction, and bubble growth in a steady state predicted that the concentration of the reactant diffusing from the surrounding depended on the droplet size and the bubble location inside the droplet, in good agreement with experimental results. Our results reveal that the reaction rate may be spatially non-uniform in the reacting microdroplets. The findings may have implications for formulating chemical properties and uses of these droplets.

physics.chem-ph↗

arXiv2022

Surface Properties of Colloidal Particles Affect Colloidal Self-Assembly in Evaporating Self-Lubricating Ternary Droplets

In this work, we unravel the role of surface properties of colloidal particles on the formation of supraparticles (clusters of colloidal particles) in a colloidal Ouzo droplet. Self-lubricating colloidal Ouzo droplets are an efficient and simple approach to form supraparticles, overcoming the challenge of the coffee stain effect in situ. Supraparticles are an efficient route to high-performance materials in various fields, from catalysis to carriers for therapeutics. Yet, the role of the surface of colloidal particles in the formation of supraparticles using Ouzo droplets remains unknown. Therefore, we used silica particles as a model system and compared sterically stabilized versus electrostatically stabilized silica particles - positively and negatively charged. Additionally, we studied the effect of hydration. Hydrated negatively charged silica particles and sterically stabilized silica particles form supraparticles. Conversely, dehydrated negatively charged silica particles and positively charged amine-coated particles form flat film-like deposits. Notably, the assembly process is different for all the four types of particles. The surface modifications alter (a) the contact line motion of the Ouzo droplet and (b) the particle-oil and particle-substrate interactions. These alterations modify the particle accumulation at the various interfaces, which ultimately determines the shape of the final deposit. Thus, by modulating the surface properties of the colloidal particles, we can tune the shape of the final deposit, from a spheroidal supraparticle to a flat deposit. In the future, this approach can be used to tailor the supraparticles for applications such as optics and catalysis, where the shape affects the functionality.

cond-mat.soft↗

arXiv2022

Oscillatory droplet dissolution from competing Marangoni and gravitational flows

The dissolution or growth of a droplet in a host liquid is an important part for processes like chemical extraction, chromatography or emulsification. In this work we look at the dissolution of a pair of vertically aligned droplets immersed in water, both experimentally and with numerical simulations. The liquids used for the droplets are long chain alcohols with a low but finite solubility in water and a significantly lower density than that of the host liquid. Therefore, a solutal plume is formed above of the bottom droplet and natural convection dominates the dissolution process. We monitor the volume of the droplets and the velocity field around them over time. When the liquids of the two droplets are the same, our previously found scaling laws for the Sherwood and Reynolds numbers as functions of the Rayleigh number (Dietrich et al., 2016, J. Fluid Mech.) can be applied to the lower droplet. However, remarkably, when the liquid of the top droplet is different than that of the bottom droplet the volume as function of time becomes non-monotonic, and an oscillatory Marangoni flow at the top droplet is observed. We identify the competition between solutal Marangoni flow and density driven convection as the origin of the oscillation, and numerically model the process.

physics.flu-dyn↗

arXiv2021

Self-Propelled Detachment upon Coalescence of Surface Bubbles

The removal of microbubbles from substrates is crucial for the efficiency of many catalytic and electrochemical gas evolution reactions in liquids. The current work investigates the coalescence and detachment of bubbles generated from catalytic decomposition of hydrogen peroxide. Self-propelled detachment, induced by the coalescence of two bubbles, is observed at sizes much smaller than those determined by buoyancy. Upon coalescence, the released surface energy is partly dissipated by the bubble oscillations, working against viscous drag. The remaining energy is converted to the kinetic energy of the out-of-plane jumping motion of the merged bubble. The critical ratio of the parent bubble sizes for the jumping to occur is theoretically derived from an energy balance argument and found to be in agreement with the experimental results. The present results provide both physical insight for the bubble interactions and practical strategies for applications in chemical engineering and renewable energy technologies like electrolysis.

physics.flu-dyn↗

arXiv2021

Interfacial Partitioning Enhances Microextractionby Multicomponent Nanodroplets

The sensitive and reliable in-droplet chemical analysis benefits from the enhanced partition of an analyte into the droplets. This work, we will show that chemical reactions in surface nanodroplets can shift the partition of analytes from a highly diluted solution to the droplets. Seven types of organic acids with partition coefficients (LgP) ranging from -0.7 to 1.87 are used as model analytes dissolved in an oil solution that are extracted from the flow into aqueous nanodroplets immobilized on a substrate. The timescale of integrated extraction and reaction in droplets was represented by the decoloration time of the droplets. Our results show that the effective distribution coefficient of the analyte can be decreased by 3 to 11 times of the distribution coefficient of the analyte in the bulk liquids. The principle behind the significantly shifted partition is proposed to be enhanced the transfer of the analyte across the droplet surface. The chemical reaction in the droplets enhances the partition of the analyte from a highly diluted solution. Our results show that the interfacial behavior of the analyte may be advantageous as it may improve extraction and partition. Such enhanced extraction may be leveraged for sensitive chemical detection using reactive droplets.

cond-mat.soft↗

arXiv2021

Size Effect on Reaction Rate of Surface Nanodroplets

Compartmentalizing reagents within small droplets is promising for highly efficient conversion and simplified procedures in many biphasic chemical reactions. In this work, surface nanodroplets (i.e., less than 100 nm in their maximal height) were employed to quantitatively understand the size effect on the chemical reaction rate of droplets. In our systems, a surface-active reactant in pure or binary nanodroplets reacted with the reactant in the bulk flow. Meanwhile, the product was removed from the droplet surface. The shrinkage rate of the nanodroplets was characterized by analyzing the lateral size as a function of time, where the droplet size was solely determined by chemical reaction rate at a given flow condition for the transport of the reactant and the product. We found that the overall kinetics increases rapidly with the decrease of droplets lateral radius R, as dR/dt ~ R^(-2). The faster increase in the concentration of the product in smaller droplets contributes to accelerating reaction kinetics. The enhancement of reaction rates from small droplet sizes was further confirmed when a non-reactive compound presented inside the droplets without reducing the concentrations of the reactant and the product on the droplet surface. The results of our study improve the understanding of chemical kinetics with droplets. Our findings highlight the effectiveness of small droplets for the design and control of enhanced chemical reactions in a broad range of applications.

cond-mat.soft↗

arXiv2021

How fast do microdroplets generated during liquid-liquid phase separation move in a confined 2D space?

How liquid transport occurs in confined spaces is relevant to many industrial and lab-scale processes, ranging from enhanced oil recovery to drug delivery systems. In this work, we investigate propelling microdroplets that form from liquid-liquid phase separation in a quasi-2D chamber, focusing on the direction and speed of microdroplets in response to local composition gradients. The confined ternary solution in our experiments comprises a model oil, a good solvent (ethanol) and a poor solvent (water). Depending on the initial solution composition, water-rich or oil-rich microdroplets, form and move spontaneously as the ternary solution mixes with and is displaced by water diffusing from a deep side channel. Microdroplet movement is followed in situ using high-speed bright-field imaging or fluorescence imaging when the solution is doped with a dye. Local ethanol composition gradients are estimated from the variation of fluorescence intensity in the local continuous liquid surrounding the mobile microdroplets. From phase separation of the ternary solution with high oil concentration, mobile oil-rich microdroplets form in a water-rich zone, accompanying the formation of water-rich microdroplets in an oil-rich zone. The fast movement of oil-rich microdroplets induces directional flow transport that mobilizes water-rich microdroplets close to the water-rich zone. The average microdroplet speed increases with the initial oil concentration in the ternary solution. The fastest speed of oil-rich microdroplets observed in our experiments is ~150 $μ$m/s along the surface of a hydrophobic wall. The presence of a sharp ethanol composition gradient is the primary driving force for the fast movement of oil-rich microdroplets in confinement. Our results demonstrate the potential of enhancing liquid transport in confinement through composition gradients arising from phase separation.

cond-mat.soft↗

arXiv2021

Marangoni instability triggered by selective evaporation of a binary liquid inside a Hele-Shaw cell

Interfacial stability is important for many processes involving heat and mass transfer across two immiscible phases. When this transfer takes place in the form of evaporation of a binary solution with one component being more volatile than the other, gradients in surface tension can arise. These gradients can ultimately destabilise the liquid-gas interface. In the present work, we study the evaporation of an ethanol-water solution, for which ethanol has a larger volatility. The solution is contained in a horizontal Hele-Shaw cell which is open from one end to allow for evaporation into air. A Marangoni instability is then triggered at the liquid-air interface. We study the temporal evolution of this instability by observing the effects that it has on the bulk of the liquid. More specifically, the growth of convective cells is visualized with confocal microscopy and the velocity field close to the interface is measured with micro-particle-image-velocimetry. The results of numerical simulations based on quasi 2D equations satisfactorily compare with the experimental observations, even without consideration of evaporative cooling, although this cooling can play an extra role in experiments. Furthermore, a linear stability analysis applied to a simplified version of the quasi 2D equations showed reasonably good agreement with the results from simulations at early times, when the instability has just been triggered and no coarsening has taken place. In particular, we find a critical Marangoni number below which a regime of stability is predicted.

physics.flu-dyn↗

arXiv2021

Surface nanodroplet-based nanoextraction from sub-milliliter volumes of dense suspensions

Cleaner analytic technique for quantifying compounds in dense suspension is needed for wastewater and environment analysis, chemical or bio-conversion process monitoring, biomedical diagnostics, food quality control among others. In this work, we introduce a green, fast, one-step method called nanoextraction for extraction and detection of target analytes from sub-milliliter dense suspensions using surface nanodroplets without toxic solvents and pre-removal of the solid contents. With nanoextraction, we achieve a limit of detection (LOD) of 10^(-9) M for a fluorescent model analyte obtained from a particle suspension sample. The LOD lower than that in water without particles 10^(-8) M, potentially due to the interaction of particles and the analyte. The high particle concentration in the suspension sample thus does not reduce the extraction efficiency, although the extraction process was slowed down up to 5 min. As proof of principle, we demonstrate the nanoextraction for quantification of model compounds in wastewater slurry containing 30 wt% sands and oily components (i.e. heavy oils). The nanoextraction and detection technology developed in this work may be used as fast analytic technologies for complex slurry samples in environment industrial waste, or in biomedical diagnostics.

cond-mat.soft↗

arXiv2021

Effects of chemical and geometric micro-structures on crystallization of surface droplets during solvent exchange

In this work, we investigate crystallization from droplets formed on micro-patterned surfaces. By solvent exchange in a micro-chamber, a ternary solution consisting of a model compound beta-alanine, water, and isopropanol, was displaced by a flow of isopropanol. In the process, oiling-out droplets formed and crystallized. Our results showed that the shape and size of the crystals on micro-patterned surfaces could be simply mediated by the flow conditions of solvent exchange. Varying flow rate, concentration, or channel height led to the formation of a thin film with micro-holes, connected network of crystals, or small diamond-shaped crystals. Rough micro-structures on the surface allowed the easy detachment of crystals from the surface. Beyond oiling-out crystallization, we demonstrated that the crystal formation from another solute dissolved in the droplets could be triggered by solvent exchange. The length of crystal fibers after the solvent exchange process was shorter at a faster flow rate. This study may provide further understanding to effectively obtain crystallization from surface droplets through the solvent exchange approach.

cond-mat.soft↗

arXiv2021

Enhanced displacement of phase separating liquid mixtures in 2D confined spaces

Displacing liquid in a confined space is important for technological processes, ranging from porous membrane separation to CO$_{2}$ sequestration. The liquid to be displaced usually consists of multiple components with different solubilities in the displacing liquid. Phase separation and chemical composition gradients in the liquids can influence the displacement rate. In this work, we investigate the effects of liquid composition on the displacement process of ternary liquid mixtures in a quasi-2D microchannel where liquid-liquid phase separation occurs concurrently. We focused on model ternary mixtures containing 1-octanol, ethanol, and water. These mixtures are displaced with water or with ethanol aqueous solution. The spatial distribution of subphases arising from phase separation and the displacement rates of the solution are impacted by the initial ternary solution composition. The boundary between the solution and displacing liquid changes from a defined interface to a diffusive interface as the initial 1-octanol composition in the solution is reduced. The displacement rate also varies non-linearly with the initial 1-octanol composition. The slowest displacement rate arises in the intermediate 1-octanol concentration, where a stable three-zone configuration forms at the boundary. At very low 1-octanol concentration, the displacement rate is fast, associated with droplet formation and motion driven by the chemical concentration gradients formed during phase separation. The excessive energy provided from phase separation may contribute to the enhanced displacement at intermediate to high 1-octanol concentrations, but not at the low 1-octanol concentration with enhancement from induced flow in confinement. The knowledge gained from this study highlights the importance of manipulating phase separation to enhance mass transport in confinement for a wide range of separation processes.

cond-mat.soft↗

arXiv2020

Self-propelling Microdroplets Generated and Sustained by Liquid-liquid Phase Separation in Confined Spaces

Flow transport in confined spaces is ubiquitous in technological processes, ranging from separation and purification of pharmaceutical ingredients by microporous membranes and drug delivery in biomedical treatment to chemical and biomass conversion in catalyst-packed reactors and carbon dioxide sequestration. In this work, we suggest a distinct pathway for enhanced liquid transport in a confined space via self-propelling microdroplets. These microdroplets can form spontaneously from localized liquid-liquid phase separation as a ternary mixture is diluted by a diffusing poor solvent. High speed images reveal how the microdroplets grow, break up and propel rapidly along the solid surface, with a maximal velocity up to ~160 um/s, in response to a sharp concentration gradient resulting from phase separation. The microdroplet self-propulsion induces a replenishing flow between the walls of the confined space towards the location of phase separation, which in turn drives the mixture out of equilibrium and leads to a repeating cascade of events. Our findings on the complex and rich phenomena of self-propelling droplets suggest an effective approach to enhanced flow motion of multicomponent liquid mixtures within confined spaces for time effective separation and smart transport processes.

cond-mat.soft↗

arXiv2020

Microfluidic device coupled with total internal reflection microscopy for in situ observation of precipitation

In situ observation of precipitation or phase separation induced by solvent addition is important in studying its dynamics. Combined with optical and fluorescence microscopy, microfluidic devices have been leveraged in studying the phase separation in various materials including biominerals, nanoparticles, and inorganic crystals. However, strong scattering from the subphases in the mixture is problematic for in situ study of phase separation with high temporal and spatial resolution. In this work, we present a quasi-2D microfluidic device combined with total internal reflection microscopy as an approach for in situ observation of phase separation. The quasi-2D microfluidic device comprises of a shallow main channel and a deep side channel. Mixing between a solution in the main channel (solution A) and another solution (solution B) in the side channel is predominantly driven by diffusion due to high fluid resistance from the shallow height of the main channel, which is confirmed using fluorescence microscopy. Moreover, relying on diffusive mixing, we can control the composition of the mixture in the main channel by tuning the composition of solution B. We demonstrate the application of our method for in situ observation of asphaltene precipitation and beta-alanine crystallization.

cond-mat.soft↗