arXiv subjects

Xuge Fan

Publications and source records attributed to Xuge Fan.

11 recordsLinked to original sources

arXiv2024

Modeling and Simulation of 2D Transducers Based on Suspended Graphene-Based Heterostructures in Nanoelectromechanical Pressure Sensors

Graphene-based 2D heterostructures exhibit excellent mechanical and electrical properties, which are expected to exhibit better performances than graphene for nanoelectromechanical pressure sensors. Here, we built the pressure sensor models based on suspended heterostructures of graphene/h-BN, graphene/MoS2, and graphene/MoSe2 by using COMSOL Multiphysics finite element software. We found that suspended circular 2D membranes show the best sensitivity to pressures compared to rectangular and square ones. We simulated the deflections, strains, resonant frequencies, and Young's moduli of suspended graphene-based heterostructures under the conditions of different applied pressures and geometrical sizes, built-in tensions, and the number of atomic layers of 2D membranes. The Young's moduli of 2D heterostructures of graphene, graphene/h-BN, graphene/MoS2, and graphene/MoSe2 were estimated to be 1.001TPa, 921.08 GPa, 551.11 GPa, and 475.68 GPa, respectively. We also discuss the effect of highly asymmetric cavities on device performance. These results would contribute to the understanding of the mechanical properties of graphene-based heterostructures and would be helpful for the design and manufacture of high-performance NEMS pressure sensors.

cond-mat.mes-hall↗

arXiv2024

Fast response and highly sensitive flexible humidity sensor based on nanocomposite film of MoS2 and graphene oxide

Graphene oxide (GO)-based humidity sensors are attracting widespread attention due to their high responsivity and low cost. However, GO-based humidity sensors generally suffer from slow response and recovery as well as poor stability,etc. Here, we reported a flexible resistive humidity sensor based on a MoS2/GO composite film that was fabricated by mixing different volumes of MoS2 and GO dispersions with adjustable volume ratios. The MoS2/GO composite film has been used as a sensing layer on screen-printed interdigital electrodes. The results show that the best device performance was achieved at a dispersion volume of 0.05 mL with the MoS2/GO volume ratio of 5:1, featuring high responsivity (~98%), fast response/recovery time (1.3/12.1 s), excellent stability and low cost. Further, the humidity sensor exhibits good linearity over a wide humidity range (33% RH-98% RH) at room temperature and can be fabricated easily and feasibly. The application of the humidity sensors we prepared in human respiration detection and human fingertip proximity detection has been demonstrated. These findings indicate the great potential of the composite of MoS2/GO in developing the next generation of high-performance humidity sensors.

cond-mat.mes-hall↗

arXiv2024

Recent Advances in Graphene-Based Humidity Sensors with the Focus of Structural Design: A Review

The advent of the 5G era means that the concepts of robot, VR/AR, UAV, smart home, smart healthcare based on IoT (Internet of Things) have gradually entered human life. Since then, intelligent life has become the dominant direction of social development. Humidity sensors, as humidity detection tools, not only convey the comfort of human living environment, but also display great significance in the fields of meteorology, medicine, agriculture and industry. Graphene-based materials exhibit tremendous potential in humidity sensing owing to their ultra-high specific surface area and excellent electron mobility under room temperature for application in humidity sensing. This review begins with the introduction of examples of various synthesis strategies of graphene, followed by the device structure and working mechanism of graphene-based humidity sensor. In addition, several different structural design methods of graphene are summarized, demonstrating the structural design of graphene can not only optimize the performance of graphene, but also bring significant advantages in humidity sensing. Finally, key challenges hindering the further development and practical application of high-performance graphene-based humidity sensors are discussed, followed by presenting the future perspectives.

cond-mat.mes-hall↗

arXiv2024

Recent Advances in Graphene-Based Pressure Sensors: A Review

In recent years, pressure sensors have been widely used as crucial technology components in industrial, healthcare, consumer electronics, and automotive safety applications. With the development of intelligent technologies, there is a growing demand for pressure sensors with higher sensitivity, smaller size, and wider detection range. Graphene and its derivatives, as novel emerging materials in recent years, have received widespread attention from researchers due to their unique mechanical and electrical properties, and are considered as promising sensing materials for the high-performance pressure sensors. In general, graphene-based pressure sensors can be classified into flexible pressure sensors and gas pressure sensors. In this paper, we firstly introduce the basic properties of graphene and its derivatives and then review the research progress of both graphene-based flexible pressure sensors and graphene-based gas pressure sensors respectively, focusing on different sensing mechanisms. Finally, the application prospects of graphene-based pressure sensors as well as future challenges are discussed.

cond-mat.mes-hall↗

arXiv2024

Graphene MEMS and NEMS

Graphene is being increasingly used as an interesting transducer membrane in micro- and nanoelectromechanical systems (MEMS and NEMS, respectively) due to its atomical thickness, extremely high carrier mobility, high mechanical strength and piezoresistive electromechanical transductions. NEMS devices based on graphene feature increased sensitivity, reduced size, and new functionalities. In this review, we discuss the merits of graphene as a functional material for MEMS and NEMS, the related properties of graphene, the transduction mechanisms of graphene MEMS and NEMS, typical transfer methods for integrating graphene with MEMS substrates, methods for fabricating suspended graphene, and graphene patterning and electrical contact. Consequently, we provide an overview of devices based on suspended and nonsuspended graphene structures. Finally, we discuss the potential and challenges of applications of graphene in MEMS and NEMS. Owing to its unique features, graphene is a promising material for emerging MEMS, NEMS and sensor applications.

cond-mat.mes-hall↗

arXiv2024

Humidity Sensing Properties of Different Atomic Layers of Graphene on SiO2/Si Substrate

Graphene has the great potential to be used for humidity sensing due to ultrahigh surface area and conductivity. However, the impact of different atomic layers of graphene on SiO2/Si substrate on the humidity sensing have not been studied yet. In this paper, we fabricated three types of humidity sensors on SiO2/Si substrate based on one to three atomic layers of graphene, in which the sensing areas of graphene are 75 {\mu}m * 72 {\mu}m and 45 {\mu}m * 72 {\mu}m, respectively. We studied the impact of both the number of atomic layers of graphene and the sensing areas of graphene on the responsivity and response/recovery time of the prepared graphene-based humidity sensors. We found the relative resistance change of the prepared devices decreased with the increase of number of atomic layers of graphene under the same change of relative humidity. Further, devices based on tri-layer graphene showed the fastest response/recovery time while devices based on double-layer graphene showed the slowest response/recovery time. Finally, we chose the devices based on double-layer graphene that have relatively good responsivity and stability for application in respiration monitoring and contact-free finger monitoring.

cond-mat.mes-hall↗

arXiv2024

Four ribbons of double-layer graphene suspending masses for NEMS applications

Graphene ribbons with a suspended proof mass for nanomechanical systems have been rarely studied. Here, we report three types of nanomechanical devices consisting of graphene ribbons (two ribbons, four ribbons-cross and four ribbons-parallel) with suspended Si proof masses and studied their mechanical properties. The resonance frequencies and built-in stresses of three types of devices ranged from tens of kHz to hundreds of kHz, and from 82.61 MPa to 545.73 MPa, respectively, both of which decrease with the increase of the size of proof mass. The devices with four graphene ribbons featured higher resonance frequencies and spring constants, but lower built-in stresses than two ribbon devices under otherwise identical conditions. The Young's modulus and fracture strain of double-layer graphene were measured to be 0.34 TPa and 1.13% respectively, by using the experimental data and finite element analysis (FEA) simulations. Our studies would lay the foundation for understanding of mechanical properties of graphene ribbons with a suspended proof mass and their potential applications in nanoelectromechanical systems.

cond-mat.mes-hall↗

arXiv2020

Nanoelectromechanical Sensors based on Suspended 2D Materials

The unique properties and atomic thickness of two-dimensional (2D) materials enable smaller and better nanoelectromechanical sensors with novel functionalities. During the last decade, many studies have successfully shown the feasibility of using suspended membranes of 2D materials in pressure sensors, microphones, accelerometers, and mass and gas sensors. In this review, we explain the different sensing concepts and give an overview of the relevant material properties, fabrication routes, and device operation principles. Finally, we discuss sensor readout and integration methods and provide comparisons against the state of the art to show both the challenges and promises of 2D material-based nanoelectromechanical sensing.

physics.app-ph↗

arXiv2020

Suspended graphene membranes with attached silicon proof masses as piezoresistive NEMS accelerometers

Graphene is an atomically thin material that features unique electrical and mechanical properties, which makes it an extremely promising material for future nanoelectromechanical systems (NEMS). Recently, basic NEMS accelerometer functionality has been demonstrated by utilizing piezoresistive graphene ribbons with suspended silicon proof masses. However, the proposed graphene ribbons have limitations regarding mechanical robustness, manufacturing yield and the maximum measurement current that can be applied across the ribbons. Here, we report on suspended graphene membranes that are fully-clamped at their circumference and that have attached silicon proof masses. We demonstrate their utility as piezoresistive NEMS accelerometers and they are found to be more robust, have longer life span and higher manufacturing yield, can withstand higher measurement currents and are able to suspend larger silicon proof masses, as compared to the previously graphene ribbon devices. These findings are an important step towards bringing ultra-miniaturized piezoresistive graphene NEMS closer towards deployment in emerging applications such as in wearable electronics, biomedical implants and internet of things (IoT) devices.

physics.app-ph↗

arXiv2020

Manufacture and Characterization of Graphene Membranes with Suspended Silicon Proof Masses for MEMS and NEMS Applications

Unparalleled strength, chemical stability, ultimate surface-to-volume ratio and excellent electronic properties of graphene make it an ideal candidate as a material for membranes in micro- and nanoelectromechanical systems (MEMS and NEMS). However, the integration of graphene into MEMS or NEMS devices and suspended structures such as proof masses on graphene membranes raises several technological challenges, including collapse and rupture of the graphene. We have developed a robust route for realizing membranes made of double-layer CVD graphene and suspending large silicon proof masses on membranes with high yields. We have demonstrated the manufacture of square graphene membranes with side lengths from 7 micro meter to 110 micro meter and suspended proof masses consisting of solid silicon cubes that are from 5 micro meter multiply 5 micro meter multiply 16.4 micro meter to 100 micro meter multiply 100 micro meter multiply 16.4 micro meter in size. Our approach is compatible with wafer-scale MEMS and semiconductor manufacturing technologies, and the manufacturing yields of the graphene membranes with suspended proof masses were greater than 90%, with more than 70% of the graphene membranes having more than 90% graphene area without visible defects. The graphene membranes with suspended proof masses were extremely robust and were able to withstand indentation forces from an atomic force microscope (AFM) tip of up to ~7000 nN. The measured resonance frequencies of the realized structures ranged from tens to hundreds of kHz, with quality factors ranging from 63 to 148. The proposed approach for the reliable and large-scale manufacture of graphene membranes with suspended proof masses will enable the development and study of innovative NEMS devices with new functionalities and improved performances.

physics.app-ph↗

arXiv2020

Graphene ribbons with suspended masses as transducers in ultra-small nanoelectromechanical accelerometers

Nanoelectromechanical system (NEMS) sensors and actuators could be of use in the development of next generation mobile, wearable, and implantable devices. However, these NEMS devices require transducers that are ultra-small, sensitive and can be fabricated at low cost. Here, we show that suspended double-layer graphene ribbons with attached silicon proof masses can be used as combined spring-mass and piezoresistive transducers. The transducers, which are realized using processes that are compatible with large-scale semiconductor manufacturing technologies, can yield NEMS accelerometers that occupy at least two orders of magnitude smaller die area than conventional state-of-the-art silicon accelerometers.

physics.app-ph↗