arXiv subjects

Yanqun Tang

Publications and source records attributed to Yanqun Tang.

At least 19 recordsLinked to original sources

arXiv2026

Flexible Rate-Splitting for Joint Unicast and Multi-Group Multicast Transmission in RIS-Assisted mmWave Networks

Joint unicast and multi-group multicast transmission with RIS and RSMA is a promising enabler for 6G services. However, existing RSMA schemes for such scenarios split only unicast messages while leaving multicast messages intact, limiting the degree of freedom of interference management. To this end, we propose a joint rate splitting framework that splits both unicast and multicast information and two RSMA schemes. The common-common fusion (CCF-RSMA) scheme encodes the unicast common part into the global multicast common stream, while the private-common fusion (PCF-RSMA) scheme merges it with the group-specific multicast private part. For each scheme, we formulate energy efficiency (EE) maximization problems under both perfect and imperfect channel state information, and jointly optimize active beamforming, RIS phase shifts and rate allocation parameters. Simulation results demonstrate that the proposed schemes significantly outperform the comparative schemes in terms of EE, thereby proving the effectiveness of the proposed framework. Moreover, CCF-RSMA is more favorable in scenarios with larger groups and higher unicast QoS demands, whereas PCF-RSMA is better suited for scenarios with smaller groups and higher multicast QoS.

eess.SP↗

arXiv2026

Flag-Preamble-Based Delay-Doppler Channel Estimation for Next-Evolution Waveforms

Accurate delay-Doppler channel estimation is critical for next-evolution waveforms (NEWs) to enable reliable signal detection. This paper proposes a robust channel estimation algorithm that integrates Flag sequences optimized via an adaptive accelerated parallel majorization-minimization (AP-MM) algorithm with a proposed channel estimation algorithm. To enable efficient, low-complexity parameter extraction and further overcome the robustness issues of conventional greedy estimation, we introduce two key enhancements, i.e., a candidate selection strategy to mitigate spurious sidelobe peaks, and a global least squares (LS) refinement stage to eliminate error propagation caused by sidelobe masking effects. Numerical results demonstrate that the proposed scheme significantly outperforms traditional existing algorithms, achieving the desired estimation accuracy.

eess.SP↗

arXiv2026

Integrated Channel Sounding and Communication: Requirements, Architecture, Challenges, and Key Technologies

Channel models are essential for the design, evaluation, and optimization of wireless communication systems. The emerging space-air-ground-sea integrated network (SAGSIN), characterized by diverse service applications and extended-spectrum operations, places even greater demands on highly accurate channel models. However, conventional channel sounding is limited by generalized measurement campaigns, inadequate cross-band consistency, and insufficient real-time adaptability, making it unable to meet the needs of SAGSIN for scenario-specific and high-precision channel modeling. To address this challenge, we propose a novel technological framework, termed integrated channel sounding and communication (ICSC). By deeply integrating sounding and communication, the ICSC enables efficient and real-time acquisition of dynamic channel characteristics during communication processes, supporting fine-grained site- and scenario-specific measurements. Furthermore, leveraging artificial intelligence techniques, ICSC can identify channel conditions and adapt waveform parameters in real-time according to scenario variations, which in turn enhances communication performance. This article first introduces the fundamental principles of the ICSC framework, elaborates on its core concepts and key advantages, and demonstrates its feasibility through the development of an integrated verification system (IVS). Subsequently, the potential applications and opportunities of the ICSC are analyzed in depth, followed by a discussion of its future development directions and remaining challenges.

eess.SP↗

arXiv2026

Cyclic Delay-Doppler Shift: A Simple Transmit Diversity Technique for Ultra-Reliable Communications in Doubly Selective Channels

Affine frequency division multiplexing (AFDM) and orthogonal time frequency space (OTFS) are two promising advanced waveforms proposed for reliable communications in high-mobility scenarios. In this paper, we introduce a simple transmit diversity technique, termed cyclic delay-Doppler shift (CDDS), for these two advanced waveforms to achieve ultra-reliable communications in doubly selective channels (DSCs). Two simple CDDS schemes, named modulation-domain CDDS (MD-CDDS) and time-domain CDDS (TD-CDDS), are proposed, which perform CDDS in advance at the transmitter before and after the modulation, respectively. We demonstrate that both of the two proposed CDDS schemes can be implemented efficiently and flexibly by multiplying the transmit vector with a well-designed precoding matrix, which is nothing but a sparse phase-compensated permutation matrix. Moreover, we theoretically and numerically prove that CDDS can provide MIMO-AFDM and MIMO-OTFS with optimal transmit diversity gain when a proper CDDS step is adopted. Compared to the conventional transmit diversity techniques, the proposed CDDS scheme enjoys the advantages of lower channel estimation overhead, implementation complexity, and signal processing latency, making it particularly suitable for ultra-reliable communications in high-mobility scenarios.

eess.SP↗

arXiv2026

A Unified Multicarrier Waveform Framework for Next-generation Wireless Networks: Principles, Performance, and Challenges

Next-generation wireless networks require enhanced flexibility, efficiency, and reliability in physical layer waveform design to address the challenges posed by heterogeneous channel conditions and stringent quality-of-service demands. To this end, this paper proposes a unified multicarrier waveform framework that provides a systematic characterization and practical implementation guidelines to facilitate waveform selection for the sixth-generation (6G) mobile networks and beyond. We commence by examining the design principles of the state-of-the-art waveforms, which are categorized into one-dimensional modulation waveforms (e.g., orthogonal frequency division multiplexing (OFDM) and affine frequency division multiplexing (AFDM)) and two-dimensional modulation waveforms (e.g., orthogonal time frequency space (OTFS)). Their inherent resilience against various channel-induced interference is further studied, revealing their distinct suitability in diverse channel conditions. Furthermore, an in-depth performance analysis is presented by comparing their key performance indicators (KPIs), followed by an extensive exploration of these advanced waveforms in various applications. Consequently, this work aims to serve as a pivotal reference for waveform adoption in future 6G standardization and network deployment.

eess.SP↗

arXiv2026

A Scalable Cloud-Edge Collaborative CKM Construction Framework Enabled by a Foundation Prior Model

Channel knowledge maps (CKMs) provide a site-specific, location-indexed knowledge base that supports environment-aware communications and sensing in 6G networks. In practical deployments, CKM observations are often noisy and irregular due to coverage-induced sparsity and hardware-induced linear/nonlinear degradations. Conventional end-to-end algorithms couple CKM prior information with task- and device-specific observations, and require labeled data and separate training for each construction configuration, which is expensive and therefore incompatible with scalable edge deployments. Motivated by the trends toward cloud-edge collaboration and the Artificial Intelligence - Radio Access Network (AI-RAN) paradigm, we develop a cloud-edge collaborative framework for scalable CKM construction, which enables knowledge sharing across tasks, devices, and regions by explicitly decoupling a generalizable CKM prior from the information provided by local observations. A foundation model is trained once in the cloud using unlabeled data to learn a generalizable CKM prior. During inference, edge nodes combine the shared prior with local observations. Experiments on the CKMImageNet dataset show that the proposed method achieves competitive construction accuracy while substantially reducing training cost and data requirements, mitigating negative transfer, and offering clear advantages in generalization and deployment scalability.

eess.SP↗

arXiv2026

SynthRM: A Synthetic Data Platform for Vision-Aided Mobile System Simulation

Vision-aided wireless sensing is emerging as a cornerstone of 6G mobile computing. While data-driven approaches have advanced rapidly, establishing a precise geometric correspondence between ego-centric visual data and radio propagation remains a challenge. Existing paradigms typically either associate 2D topology maps and auxiliary information with radio maps, or provide 3D perspective views limited by sparse radio data. This spatial representation flattens the complex vertical interactions such as occlusion and diffraction that govern signal behavior in urban environments, rendering the task of cross-view signal inference mathematically ill-posed. To resolve this geometric ambiguity, we introduce SynthRM, a scalable synthetic data platform. SynthRM implements a Visible-Aligned-Surface simulation strategy: rather than probing a global volumetric grid, it performs ray-tracing directly onto the geometry exposed to the sensor. This approach ensures pixel-level consistency between visual semantics and electromagnetic response, transforming the learning objective into a physically well-posed problem. We demonstrate the platform's capabilities by presenting a diverse, city-scale dataset derived from procedurally generated environments. By combining efficient procedural synthesis with high-fidelity electromagnetic modeling, SynthRM provides a transparent, accessible foundation for developing next-generation mobile systems for environment-aware sensing and communication.

eess.SP↗

arXiv2025

ISAC with Affine Frequency Division Multiplexing: An FMCW-Based Signal Processing Perspective

This paper investigates the sensing potential of affine frequency division multiplexing (AFDM) in high-mobility integrated sensing and communication (ISAC) from the perspective of radar waveforms. We introduce an innovative parameter selection criterion that establishes a precise mathematical equivalence between AFDM subcarriers and Nyquist-sampled frequency-modulated continuous-wave (FMCW). This connection not only provides a clear physical insight into AFDM's sensing mechanism but also enables a direct mapping from the DAFT index to delay-Doppler (DD) parameters of wireless channels. Building on this, we develop a novel input-output model in a DD-parameterized DAFT (DD-DAFT) domain for AFDM, which explicitly reveals the inherent DD coupling effect arising from the chirp-channel interaction. Subsequently, we design two matched-filtering sensing algorithms. The first is performed in the time-frequency domain with low complexity, while the second is operated in the DD-DAFT domain to precisely resolve the DD coupling. Simulations show that our algorithms achieve effective pilot-free sensing and demonstrate a fundamental trade-off between sensing performance, communication overhead, and computational complexity. The proposed AFDM outperforms classical AFDM and other variants in most scenarios.

eess.SP↗

arXiv2025

Ambiguity Function Analysis of AFDM Under Pulse-Shaped Random ISAC Signaling

This paper investigates the ambiguity function (AF) of the emerging affine frequency division multiplexing (AFDM) waveform for Integrated Sensing and Communication (ISAC) signaling under a pulse shaping regime. Specifically, we first derive the closed-form expression of the average squared discrete period AF (DPAF) for AFDM waveform without pulse shaping, revealing that the AF depends on the parameter $c_1$ and the kurtosis of random communication data, while being independent of the parameter $c_2$. As a step further, we conduct a comprehensive analysis on the AFs of various waveforms, including AFDM, orthogonal frequency division multiplexing (OFDM) and orthogonal chirp-division multiplexing (OCDM). Our results indicate that all three waveforms exhibit the same number of regular depressions in the sidelobes of their AFs, which incurs performance loss for detecting and estimating weak targets. However, the AFDM waveform can flexibly control the positions of depressions by adjusting the parameter $c_1$, which motivates a novel design approach of the AFDM parameters to mitigate the adverse impact of depressions of the strong target on the weak target. Furthermore, a closed-form expression of the average squared DPAF for pulse-shaped random AFDM waveform is derived, which demonstrates that the pulse shaping filter generates the shaped mainlobe along the delay axis and the rapid roll-off sidelobes along the Doppler axis. Numerical results verify the effectiveness of our theoretical analysis and proposed design methodology for the AFDM modulation.

eess.SP↗

arXiv2025

From OFDM to AFDM: Enabling Adaptive Integrated Sensing and Communication in High-Mobility Scenarios

Integrated sensing and communication (ISAC) is a key feature of next-generation wireless networks, enabling a wide range of emerging applications such as vehicle-to-everything (V2X) and unmanned aerial vehicles (UAVs), which operate in high-mobility scenarios. Notably, the wireless channels within these applications typically exhibit severe delay and Doppler spreads. The latter causes serious communication performance degradation in the Orthogonal Frequency-Division Multiplexing (OFDM) waveform that is widely adopted in current wireless networks. To address this challenge, the recently proposed Doppler-resilient affine frequency division multiplexing (AFDM) waveform, which uses flexible chirp signals as subcarriers, shows great potential for achieving adaptive ISAC in high-mobility scenarios. This article provides a comprehensive overview of AFDM-ISAC. We begin by presenting the fundamentals of AFDM-ISAC, highlighting its inherent frequency-modulated continuous-wave (FMCW)-like characteristics. Then, we explore its ISAC performance limits by analyzing its diversity order, ambiguity function (AF), and Cramer-Rao Bound (CRB). Finally, we present several effective sensing algorithms and opportunities for AFDM-ISAC, with the aim of sparking new ideas in this emerging field.

eess.SP↗

arXiv2025

Affine Frequency Division Multiplexing for Communication and Channel Sounding: Requirements, Challenges, and Key Technologies

Channel models are crucial for theoretical analysis, performance evaluation, and deployment of wireless communication systems. Traditional channel sounding systems are insufficient for handling the dynamic changes of channels in the next-generation space-air-ground-sea integrated networks (SAGSIN), which often results in outdated channel models that fail to provide reliable prior information for communication systems. To address this challenge, this paper proposes an integrated channel sounding and communication (ICSC) method as a practical solution. Unlike orthogonal frequency division multiplexing, affine frequency division multiplexing (AFDM) provides a full delay-Doppler representation of the channel, achieving optimal diversity in time-frequency doubly dispersive channels and effectively addressing the aforementioned challenges. Thus, we investigate the fundamental principles of AFDM, showing how it enables simultaneous communication and channel sounding, and explore key performance metrics for both functionalities. We also clarify the distinction and relationship between channel sounding, estimation, tracking and scatterer sensing. Additionally, several potential application scenarios for AFDM-ICSC are explored. Finally, we highlight the key challenges in implementing AFDM-ICSC, outline future research directions, and provide valuable insights for the continued development of this technology.

eess.SP↗

arXiv2025

Multiple-Mode Affine Frequency Division Multiplexing with Index Modulation

Affine frequency division multiplexing (AFDM), a promising multicarrier technique utilizing chirp signals, has been envisioned as an effective solution for high-mobility communication scenarios. In this paper, we develop a multiple-mode index modulation scheme tailored for AFDM, termed as MM-AFDM-IM, which aims to further improve the spectral and energy efficiencies of AFDM. Specifically, multiple constellation alphabets are selected for different chirp-based subcarriers (chirps). Aside from classical amplitude/phase modulation, additional information bits can be conveyed by the dynamic patterns of both constellation mode selection and chirp activation, without extra energy consumption. Furthermore, we discuss the mode selection strategy and derive an asymptotically tight upper bound on the bit error rate (BER) of the proposed scheme under maximum-likelihood detection. Simulation results are provided to demonstrate the superior performance of MM-AFDM-IM compared to conventional benchmark schemes.

eess.SP↗

arXiv2025

Ambiguity Function Analysis of AFDM Signals for Integrated Sensing and Communications

Affine frequency division multiplexing (AFDM) is a promising chirp-based waveform with high flexibility and resilience, making it well-suited for next-generation wireless networks, particularly in high-mobility scenarios. In this paper, we investigate the ambiguity functions (AFs) of AFDM signals, which fundamentally characterize their range and velocity estimation capabilities in both monostatic and bistatic settings. Specifically, we first derive the auto-ambiguity function (AAF) of an AFDM chirp subcarrier, revealing its "spike-like" local property and "periodic-like" global property along the rotated delay and Doppler dimensions. This structure naturally forms a parallelogram for each localized pulse of the AAF of the AFDM chirp subcarrier, enabling unambiguous target sensing. Then, we study the cross-ambiguity function (CAF) between two different AFDM chirp subcarriers, which exhibits the same local and global properties as the AAF but with an additional shift along the Doppler dimension. We then extend our analysis to the AF of various typical AFDM frames, considering both deterministic pilot and random data symbols. In particular, we demonstrate that inserting guard symbols in AFDM facilitates interference-free sensing. Simulation results validate our theoretical findings, highlighting AFDM's strong potential for ISAC applications.

eess.SP↗

arXiv2025

AI-based Environment-Aware XL-MIMO Channel Estimation with Location-Specific Prior Knowledge Enabled by CKM

Accurate and efficient acquisition of wireless channel state information (CSI) is crucial to enhance the communication performance of wireless systems. However, with the continuous densification of wireless links, increased channel dimensions, and the use of higher-frequency bands, channel estimation in the sixth generation (6G) and beyond wireless networks faces new challenges, such as insufficient orthogonal pilot sequences, inadequate signal-to-noise ratio (SNR) for channel training, and more sophisticated channel statistical distributions in complex environment. These challenges pose significant difficulties for classical channel estimation algorithms like least squares (LS) and maximum a posteriori (MAP). To address this problem, we propose a novel environment-aware channel estimation framework with location-specific prior channel distribution enabled by the new concept of channel knowledge map (CKM). To this end, we propose a new type of CKM called channel score function map (CSFM), which learns the channel probability density function (PDF) using artificial intelligence (AI) techniques. To fully exploit the prior information in CSFM, we propose a plug-and-play (PnP) based algorithm to decouple the regularized MAP channel estimation problem, thereby reducing the complexity of the optimization process. Besides, we employ Tweedie's formula to establish a connection between the channel score function, defined as the logarithmic gradient of the channel PDF, and the channel denoiser. This allows the use of the high-precision, environment-aware channel denoiser from the CSFM to approximate the channel score function, thus enabling efficient processing of the decoupled channel statistical components. Simulation results show that the proposed CSFM-PnP based channel estimation technique significantly outperforms the conventional techniques in the aforementioned challenging scenarios.

eess.SP↗

arXiv2025

Joint Security-Latency Design for Short Packet-Based Low-Altitude Communications

In this article, a joint security and latency analysis of short packet-based low-altitude communications when the eavesdropper is close to the receiver is addressed. To reveal the impacts of the signal-to-noise ratio (SNR) and block-length on latency in communications, we propose a new metric named secure latency (SL) and derive the expressions for the effective secure probability (ESP) and the average SL. To minimize the average SL, different transmission designs are analyzed, in which the optimal solutions of SNR and block-length are provided. Numerical results validate our analysis and reveal the trade-off between reliability and security and the impacts of the block-length, SNR, and packet-generating rate on average SL, of which SNR and the block-length account for main factors. In addition, we find that the performance of SL can be enhanced by allocating less SNR.

eess.SP↗

arXiv2025

Joint Sparse Graph for Enhanced MIMO-AFDM Receiver Design

Affine frequency division multiplexing (AFDM) is a promising chirp-assisted multicarrier waveform for future high-mobility communications. This paper is devoted to enhanced receiver design for multiple input and multiple output AFDM (MIMO-AFDM) systems. Firstly, we introduce a unified variational inference (VI) approach to approximate the target posterior distribution, under which the belief propagation (BP) and expectation propagation (EP)-based algorithms are derived. As both VI-based detection and low-density parity-check (LDPC) decoding can be expressed by bipartite graphs in MIMO-AFDM systems, we construct a joint sparse graph (JSG) by merging the graphs of these two for low-complexity receiver design. Then, based on this graph model, we present the detailed message propagation of the proposed JSG. Additionally, we propose an enhanced JSG (E-JSG) receiver based on the linear constellation encoding model. The proposed E-JSG eliminates the need for interleavers, de-interleavers, and log-likelihood ratio transformations, thus leading to concurrent detection and decoding over the integrated sparse graph. To further reduce detection complexity, we introduce a sparse channel method by approaximating multiple graph edges with insignificant channel coefficients into a single edge on the VI graph. Simulation results show the superiority of the proposed receivers in terms of computational complexity, detection and decoding latency, and error rate performance compared to the conventional ones.

eess.SP↗

arXiv2025

Affine Frequency Division Multiplexing: Extending OFDM for Scenario-Flexibility and Resilience

Next-generation wireless networks are conceived to provide reliable and high-data-rate communication services for diverse scenarios, such as vehicle-to-vehicle, unmanned aerial vehicles, and satellite networks. The severe Doppler spreads in the underlying time-varying channels induce destructive inter-carrier interference (ICI) in the extensively adopted orthogonal frequency division multiplexing (OFDM) waveform, leading to severe performance degradation. This calls for a new air interface design that can accommodate the severe delay-Doppler spreads in highly dynamic channels while possessing sufficient flexibility to cater to various applications. This article provides a comprehensive overview of a promising chirp-based waveform named affine frequency division multiplexing (AFDM). It is featured with two tunable parameters and achieves optimal diversity order in doubly dispersive channels (DDC). We study the fundamental principle of AFDM, illustrating its intrinsic suitability for DDC. Based on that, several potential applications of AFDM are explored. Furthermore, the major challenges and the corresponding solutions of AFDM are presented, followed by several future research directions. Finally, we draw some instructive conclusions about AFDM, hoping to provide useful inspiration for its development.

eess.SP↗

arXiv2024

A DAFT Based Unified Waveform Design Framework for High-Mobility Communications

With the increasing demand for multi-carrier communication in high-mobility scenarios, it is urgent to design new multi-carrier communication waveforms that can resist large delay-Doppler spreads. Various multi-carrier waveforms in the transform domain were proposed for the fast time-varying channels, including orthogonal time frequency space (OTFS), orthogonal chirp division multiplexing (OCDM), and affine frequency division multiplexing (AFDM). Among these, the AFDM is a strong candidate for its low implementation complexity and ability to achieve optimal diversity. This paper unifies the waveforms based on the discrete affine Fourier transform (DAFT) by using the chirp slope factor "k" in the time-frequency representation to construct a unified design framework for high-mobility communications. The design framework is employed to verify that the bit error rate performance of the DAFT-based waveform can be enhanced when the signal-to-noise ratio (SNR) is sufficiently high by adjusting the chirp slope factor "k".

eess.SP↗