arXiv subjects

Yansong Yang

Publications and source records attributed to Yansong Yang.

8 recordsLinked to original sources

arXiv2026

Suppressing Acoustomigration and Temperature Rise for High-power Robust Acoustics

High-frequency acoustic wave transducers, vibrating at gigahertz (GHz), favored for their compact size, are not only dominating the front-end of mobile handsets but are also expanding into various interdisciplinary fields, including quantum acoustics, acoustic-optics, acoustic-fluids, acoustoelectric, and sustainable power conversion systems. However, like strong vibration can "shake off" substances and produce heat, a long-standing bottleneck has been the ability to harness acoustics under high-power vibration loads, while simultaneously suppressing temperature rise, especially for IDT-based surface acoustic wave (SAW) systems. Here, we proposed a layered acoustic wave (LAW) platform, utilizing a quasi-infinite multifunctional top layer, that redefines mechanical and thermal boundary conditions to overcome three fundamental challenges in high-power acoustic wave vibration: self-heating, thermal instability, and acoustomigration. By simply leveraging a simplified, thick single-material overlayer to achieve electro-thermo-mechanical co-design, this acoustic platform moves beyond prior substrate-focused thermal management in SAW technology. It demonstrates, for the first time from the top boundary, simultaneous redistribution of the von Mises stress field and the creation of an efficient vertical thermal dissipation path. The LAW transducer, vibrating at over 2 GHz, achieves a 70% reduction in temperature rise under identical power loads, a first-order temperature coefficient of frequency (TCF) of -13 ppm/C with minimal dispersion, and an unprecedented threshold power density of 45.61 dBm/mm2 - over one order-of-magnitude higher than that of state-of-the-art thin-film surface acoustic wave (TF-SAW) counterparts at the same wavelength.

eess.SP↗

arXiv2019

A Laterally Vibrating Lithium Niobate MEMS Resonator Array Operating at 500°C in Air

This paper is the first report of the high-temperature characteristics of a laterally vibrating piezoelectric lithium niobate (LiNbO$_{3}$) MEMS resonator array up to 500°C in air. After a high-temperature burn-in treatment, device quality factor (Q) is enhanced to 508 and the resonance shifts to a lower frequency and remains stable up to 500°C. During subsequent in situ high-temperature testing, the resonant frequencies of two coupled shear horizontal (SH0) modes in the array are 87.36 MHz and 87.21 MHz at 25°C and 84.56 MHz and 84.39 MHz at 500°C, correspondingly, representing a -3% shift in frequency over the temperature range. Upon cooling to room temperature, the resonant frequency returns to 87.36 MHz, demonstrating recoverability of device performance. The first- and second-order temperature coefficient of frequency (TCF) are found to be -95.27 ppm/°C and 57.5 ppb/°C$^{2}$ for resonant mode A, and -95.43 ppm/°C and 55.8 ppb/°C$^{2}$ for resonant mode B, respectively. The temperature-dependent quality factor (Q) and electromechanical coupling coefficient ($k_{t}^{2}$) are extracted and reported. Device Q decreases to 334 after high-temperature exposure, while $k_{t}^{2}$ increases to 12.40%. This work supports the use of piezoelectric LiNbO$_{3}$ as a material platform for harsh environment radio-frequency (RF) resonant sensors (e.g. temperature and infrared).

physics.app-ph↗

arXiv2019

5-GHz Antisymmetric Mode Acoustic Delay Lines in Lithium Niobate Thin Film

We present the first group of acoustic delay lines (ADLs) at 5 GHz, using the first-order antisymmetric (A1) mode in Z-cut lithium niobate thin films. The demonstrated ADLs significantly surpass the operation frequency of the previous works with similar feature sizes, because of its simultaneously fast phase velocity, large coupling coefficient, and low-loss. In this work, the propagation characteristics of the A1 mode in lithium niobate is analytically modeled and validated with finite element analysis. The design space of A1 ADLs is then investigated, including both the fundamental design parameters and those introduced from the practical implementation. The implemented ADLs at 5 GHz show a minimum insertion loss of 7.94 dB, an average IL of 9.1 dB, and a fractional bandwidth around 4%, with delays ranging between 15 ns to 109 ns and the center frequencies between 4.5 GHz and 5.25 GHz. The propagation characteristics of A1 mode acoustic waves have also been extracted for the first time. The A1 ADL platform can potentially enable wide-band high-frequency passive signal processing functions for future 5G applications in the sub-6 GHz spectrum bands.

eess.SP↗

arXiv2019

4.5 GHz Lithium Niobate MEMS Filters with 10% Fractional Bandwidth for 5G Front-ends

This paper presents a new class of micro-electro-mechanical system (MEMS) C-band filters for 5G front-ends. The filter is comprised of resonators based on the first-order asymmetric Lamb wave (A1) mode in thin film lithium niobate. Two filters have been demonstrated at 4.5 GHz with sharp roll-off, flat in-band group delay, and spurious-free response over a wide frequency range. The first design shows a fractional bandwidth (FBW) of 10%, an insertion loss (IL) of 1.7 dB, an out-of-band (OoB) rejection of -13 dB, and a compact footprint of 0.36 mm2, while the second design shows an FBW of 8.5%, an IL of 2.7 dB, an OoB rejection of -25 dB, and a footprint of 0.9 mm^2. The demonstrations herein mark the largest fractional bandwidth (FBW) achieved for acoustic-only filters at 5G frequencies.

eess.SP↗

arXiv2019

High performance fully etched isotropic microring resonators in thin-film lithium niobate on insulator platform

We present our design, fabrication, and experimental results for very high-performance isotropic microring resonators with small radii (~ 30 μm) based on single-mode strip waveguides and transverse magnetic (TM) polarization in a fully etched lithium niobate (Z-cut) thin-film on insulator. The loss of the devices is predicted to be < 10 dB/cm, and is measured to be ~ 7 dB/cm. The measured optical responses of microring resonators exhibit an extinction of ~ 25 dB (close to critical coupling), a 3 dB optical bandwidth of 49 pm (~ 6 GHz) for all-pass structures, an extinction of ~ 10 dB for add-drop structures, and a free spectral range of ~ 5.26 nm, all of which are in excellent agreement with the design. This work is the first step towards ultra-compact and fully isotropic optical modulators in thin-film lithium niobate on insulator.

physics.app-ph↗

arXiv2018

Toward Ka Band Acoustics: Lithium Niobate Asymmetrical Mode Piezoelectric MEMS Resonators

This work presents a new class of micro-electro-mechanical system (MEMS) resonators toward Ka band (26.5-40GHz) for fifth-generation (5G) wireless communication. Resonant frequencies of 21.4 and 29.9 GHz have been achieved using the fifth and seventh order asymmetric (A5 and A7) Lamb-wave modes in a suspended Z-cut lithium niobate (LiNbO3) thin film. The fabricated device has demonstrated an electromechanical coupling (kt2) of 1.5% and 0.94% and extracted mechanical Qs of 406 and 474 for A5 and A7 respectively. The quality factors are the highest reported for piezoelectric MEMS resonators operating at this frequency range. The demonstrated performance has shown the strong potential of LiNbO3 asymmetric mode devices to meet the front-end filtering requirements of 5G.

physics.app-ph↗

arXiv2018

A Radio Frequency Non-reciprocal Network Based on Switched Acoustic Delay Lines

This work demonstrates the first non-reciprocal network based on switched low-loss acoustic delay lines. The 4-port circulator is built upon a recently reported frequency-independent, programmable, non-reciprocal framework based on switched delay lines. The design space for such a system, including the origins of the insertion loss and harmonic responses, is theoretically investigated, illustrating that the key to better performance and low-cost modulation signal synthesis lies in a large delay. To implement a large delay, we resort to in-house fabricated low-loss, wide-band lithium niobate (LiNbO3) SH0 mode acoustic delay lines employing single-phase unidirectional transducers (SPUDT). The 4-port circulator, consisting of two switch modules and one delay line module, has been modularly designed, assembled, and tested. The design process employs time-domain full circuit simulation and the results match well with measurements. A 18.8 dB non-reciprocal contrast between insertion loss (IL = 6.6 dB) and isolation (25.4 dB) has been achieved over a fractional bandwidth of 8.8% at a center frequency 155 MHz, using a record low switching frequency of 877.19 kHz. The circulator also shows 25.9 dB suppression for the intra-modulated tone and 30 dBm for IIP3. Upon further development, such a system can potentially lead to future wide-band, low-loss chip-scale nonreciprocal RF systems with unprecedented programmability.

eess.SP↗

arXiv2018

A Radio Frequency Non-reciprocal Network Based on Switched Low-loss Acoustic Delay Lines

This work demonstrates the first non-reciprocal network based on switched low-loss acoustic delay lines. A 21 dB non-reciprocal contrast between insertion loss (IL=6.7 dB) and isolation (28.3 dB) has been achieved over a fractional bandwidth of 8.8% at a center frequency 155MHz, using a record low switching frequency of 877.22 kHz. The 4-port circulator is built upon a newly reported framework by the authors, but using two in-house fabricated low-loss, wide-band lithium niobate (LiNbO3) delay lines with single-phase unidirectional transducers (SPUDT) and commercial available switches. Such a system can potentially lead to future wide-band, low-loss chip-scale nonreciprocal RF systems with unprecedented programmability.

eess.SP↗