arXiv subjects

Yanwei Ma

Publications and source records attributed to Yanwei Ma.

At least 37 records · Page 2Linked to original sources

arXiv2015

Large transport Jc in Cu-sheathed Sr0.6K0.4Fe2As2 superconducting tape conductors

Copper sheath is the first choice for manufacturing high-Tc superconducting wires and tapes because of its high electrical and thermal conductivities, low cost and good mechanical properties. However, Cu can easily react with superconducting cores, such as BSCCO, MgB2 and pnictides, during high-temperature sintering process and therefore drastically decrease the transport Jc. Here, we report the fabrication of Cu-sheathed Sr1-xKxFe2As2 tapes with superior Jc performance using a simple hot pressing method that is capable of eliminating the lengthy high-temperature sintering required by conventional process. We obtained high-quality Sr1-xKxFe2As2 tapes with processing at 800oC for 30 minutes and measured high Tc and sharp transition. This rapid fabrication method can effectively thwart the diffusion of Cu into polycrystalline Sr-122 core. As a consequence, we achieved high transport Jc of 3.1x10^4 A/cm^2 in 10 T and 2.7x10^4 A/cm^2 in 14 T at 4.2 K. The in-field Jc performance is by far the highest reported for Cu-sheathed high-Tc conductors. Our results demonstrate the potential of Cu sheath for practical application of pnictide wires and tapes.

cond-mat.supr-con↗

arXiv2015

High performance FeSe0.5Te0.5 thin films grown at low temperature by pulsed laser deposition

We report on fully epitaxial FeSe0.5Te0.5 (FST) thin films with high-quality grown on CaF2 (00l) substrate at a low temperature of 300°C by pulsed laser deposition. The transport Jc of thin films is up to 1.36 MA/cm2 in self-field and 0.97 MA/cm2 in 9 T at 4.2 K, indicating very weak field dependence. A nearly isotropy of Jc (γ= Jc(H//ab)/Jc(H//c) as low as 1.09 at 9 T is achieved in the FST thin films. Moreover, no clear amorphous interfacial layer presents between the film and the substrate probably ascribing to low temperature and low laser repetition rate grown, while the thickness of reaction layer is approximate 5 nm in many other works. The evidences of transmission electron microscopy show some lattices with lateral size of < 5 nm x 20 nm seem to be disturbed. Those location defects are thought to be responsible for nearly isotropic behavior of superconductivity.

cond-mat.supr-con↗

arXiv2014

Hot pressing to enhance the transport Jc of Sr0.6K0.4Fe2As2 superconducting tapes

High-performance Sr0.6K0.4Fe2As2 (Sr-122) tapes have been successfully fabricated using hot pressing (HP) process. The effect of HP temperatures (850-925 C) on the c-axis texture, resistivity, Vickers micro-hardness, microstructure and critical current properties has been systematically studied. Taking advantage of high degree of c-axis texture, well grain connectivity and and large concentration of strong-pinning defects, we are able to obtain an excellent Jc of 1.2x10^5 A/cm^2 at 4.2 K and 10 T for Sr-122 tapes. More importantly, the field dependence of Jc turns out to be very weak, such that in 14 T the Jc remains ~1.0x10^5 A/cm^2. These Jc values are the highest ever reported so far for iron-pnictide wires and tapes, achieving the level desired for practical applications. Our results clearly strengthen the position of iron-pnictide conductors as a competitor to the conventional and MgB2 superconductors for high field applications.

cond-mat.supr-con↗

arXiv2014

High critical current density in textured Ba-122/Ag tapes fabricated by scalable rolling process

The industrial manufacturing of the long-length iron-pnictide wires and tapes requires simple and low-cost technology. Although the transport critical current density of the FeAs-122 tapes has already achieved the practical application level, their fabrication procedures are relatively complicated or required specialized instruments. Ag-sheathed Ba0.6K0.4Fe2As2 superconducting tapes were fabricated by the scalable rolling process. At 4.2 K and 10 T, the critical current density Jc has achieved 5.4x10^4 A/cm2. We ascribe the excellent performance to the high purity and homogeneity of the superconducting phase, high density and high c-axis texture of the superconducting core. Our method provides a simple way to scale up the production of the long-length iron-based superconducting tapes with high Jc.

cond-mat.supr-con↗

arXiv2014

Enhancement of transport critical current density of SmFeAsO1-xFx tapes fabricated by an ex-situ powder-in-tube method with a Sn-presintering process

SmFeAsO1-xFx (Sm1111) tapes were prepared by an ex-situ powder-in-tube method with a Sn-presintering process. Scanning electron microscopy revealed apparent difference in microstructure between Sn-presintered tapes and the previously reported polycrystalline Sm1111 bulk, since Sn has reduced FeAs wetting phase and filled the voids between Sm1111 grains. The Sn-presintered tapes showed significant enhanced field dependences of transport Jc compared with Sn-added tapes. A highest transport critical current density (Jc) of 3.45x10^4 A cm-2 at 4.2 K and self-field is achieved. Magneto-optical (MO) imaging further confirmed large and well-distributed global and intergranular Jc in Sn-presintered Sm1111 tapes.

cond-mat.supr-con↗

arXiv2014

Realization of practical level current densities in Sr0.6K0.4Fe2As2 tape conductors for high-field applications

122 type pnictide superconductors are of particular interest for high-field applications because of their large upper critical fields Hc2 (> 100 T), low Hc2 anisotropy r (< 2), and high thin-film critical current densities Jc (> 1 MA/cm2 at 4.2 K). Successful magnet applications require fabrication of polycrystalline superconducting wires that exhibit large in-field Jc, which is limited by poor grain coupling and weak-link behavior at grain boundaries. Here we report our recent achievement in the developing Sr0.6K0.4Fe2As2 tapes with transport Jc up to 0.1 MA/cm2 at 10 T and 4.2 K. This value is by far the highest ever recorded for iron based superconducting wires and has surpassed the threshold for practical application for the first time. The synergy effects of enhanced grain connectivity, alleviation of the weak-link behavior at grain boundaries, and the strong intrinsic pinning characteristics led to the superior Jc performance exhibited in our samples. This advanced Jc result opens up the possibility for iron-pnictide superconducting wires to win the race in high-field magnet applications.

cond-mat.supr-con↗

arXiv2014

Strongly enhanced current densities in Sr0.6K0.4Fe2As2 superconducting tapes

Improving transport current has been the primary issue for practical application of superconducting wires and tapes. However, the porous nature of powder-in-tube (PIT) processed iron-based superconducting tapes is thought to be one of the important reasons for the low Jc values. In this work, the superconducting core density of ex-situ Sr0.6K0.4Fe2As2 tapes was significantly improved by employing a simple hot pressing as an alternative route for final sintering. At 4.2 K, the transport Jc values showed excellent values of 5.1x10^4 A/cm^2 at 10 T and 4.3x10^4 A/cm^2 at 14 T, respectively, which attain the Jc level desired for practical applications. Moreover, the Jc values exhibited extremely weak magnetic field dependence. These results clearly demonstrate that PIT pnictide wire conductors are very promising for high field magnet applications.

cond-mat.supr-con↗

arXiv2013

Large transport critical currents and magneto-optical imaging of textured Sr1-xKxFe2As2 superconducting tapes

We report the temperature dependence of the transport critical current density (Jc) in textured Sr1-xKxFe2As2/Fe (Sr122) tapes fabricated by an ex situ powder-in-tube process. Critical currents were measured in magnetic fields up to 0-15 T and/or the temperature range 4.2-30 K by using a dc four-probe method. It was found that textured Sr122 tapes heat-treated at low temperatures showed higher transport Jc performance due to much improved intergrain connections. At temperatures of 20 K, easily obtained using a cryocooler, Jc reached ~ 10^4 A/cm^2 in self field, which is the highest transport value of ferropnictide wires and tapes reported so far. Magneto-optical imaging observations further revealed significant and well distributed global Jc at 20 K in our tapes. These results demonstrate that 122 type superconducting tapes are promising for high-field applications at around 20 K.

cond-mat.supr-con↗

arXiv2013

High critical current density and low anisotropy in textured Sr1-xKxFe2As2 tapes for high field applications

From the application point of view, large critical current densities Jc (H) for superconducting wires are required, preferably for magnetic fields higher than 5 T. Here we show that strong c-axis textured Sr1-xKxFe2As2 tapes with nearly isotropic transport Jc were fabricated by an ex-situ powder-in-tube (PIT) process. At 4.2 K, the Jc values show extremely weak magnetic field dependence and reach high values of 1.7x10^4 A/cm^2 at 10 T and 1.4x10^4 A/cm^2 at 14 T, respectively, these values are by far the highest ever reported for iron based wires and approach the Jc level desired for practical applications. Transmission electron microscopy investigations revealed that amorphous oxide layers at grain boundaries were significantly reduced by Sn addition which resulted in greatly improved intergranular connectivity. Our results demonstrated the strong potential of using iron based superconductors for high field applications.

cond-mat.supr-con↗

arXiv2012

Fabrication and transport properties of Sr0.6K0.4Fe2As2 multifilamentary superconducting wires

Seven-core Ag/Fe sheathed Sr0.6K0.4Fe2As2 (Sr-122) superconducting wires were produced by the ex situ powder-in-tube (PIT) method. The relationship between the cold-work deformation process and the superconducting properties of wires were systematically studied. It was found that flat rolling can efficiently increase the density of the superconducting core and largely improve the transport critical current density (Jc) of as-drawn wires. The Jc of the best sample achieved 21.1 kA/cm^2 at 4.2 K in self field, and showed very weak magnetic field dependence in high fields. Our result suggested a promising future of multifilamentary iron-based superconductors in practical application.

cond-mat.supr-con↗

arXiv2012

Progress in wire fabrication of iron-based superconductors

Iron-based superconductors, with Tc values up to 55 K, are of great interest for applications, due to their lower anisotropies and ultrahigh upper critical fields. In the past 4 years, great progress has been made in the fabrication of iron-based superconducting wires and tapes using the powder-in-tube (PIT) processing method, including main three types of 122, 11, and 1111 iron-based parent compounds. In this article, an overview of the current state of development of iron-based superconducting wires and tapes is presented. We focus on the fabrication techniques used for 122 pnictide wires and tapes, with an emphasis on their meeting the critical current requirements for making high-performance conductors, such as a combination of using Ag sheath, addition element and optimized heat treatment to realize high Jc, ex situ process employed to reduce non-superconducting phases and to obtain a high relative density, and a texture control to improve grain connectivity. Of particular interest is that so far transport Jc values above 10^4 A/cm^2 at 4.2 K and 10 T are obtained in 122 type tapes, suggesting that they are prospective candidates for high-field applications. Finally, a perspective and future development of PIT pnictide wires are also given.

cond-mat.supr-con↗

arXiv2012

Calculation of the transport critical current density of c-axis textured 122 iron-based superconductors

The c-axis textured Sr1-xKxFe2As2 tapes produced by cold rolling and post-annealing, could carry a high super-current over 2*104 A/cm2. However, the magnitude is far from its maximum, because of the current obstacles associated with various defects in the material. To predict the maximal transport critical current density, we modeled the current paths in a c-axis textured polycrystal as a three-dimensional flow network, and calculated the maximum flow with the Ford-Fulkerson algorithm. It indicates that a much higher super-current of about 2*105 A/cm2 could be achieved in an ideal c-axis textured K-doped 122 polycrystal. The dependences of transport Jc on density, content of invalid boundary and grain size and shape were also studied. The results imply that, over 30% of the grain boundaries in the reported c-axis textured Sr1-xKxFe2As2 tapes may act as current obstacles, and the large ratio of width to thickness was expected to be the most favorable grain shape for high transport Jc in c-axis textured 122 superconducting tapes.

cond-mat.supr-con↗

arXiv2012

Improved transport critical currents in Ag and Pb co-doped BaxK1-xFe2As2 superconducting tapes

Fe-clad BaxK1-xFe2As2 superconducting tapes were fabricated by the ex situ powder-in-tube method combined with a short high-temperature annealing technique. The effect of annealing time and different dopants on the transport properties of the BaxK1-xFe2As2 tapes were systematically studied. By co-doping with Ag and Pb, the transport critical current density Jc of BaxK1-xFe2As2 tapes was significantly improved in whole field region and the highest transport Jc was up to 1.4x10^4 A/cm^2 (Ic=100 A) at 4.2K in self field. It is proposed that the superior Jc in the co-doped samples are due to the combine effect of Pb doping at low fields and Ag doping at high fields.

cond-mat.supr-con↗

arXiv2012

Effect of starting materials on the superconducting properties of SmFeAsO1-xFx tapes

SmFeAsO1-xFx tapes were prepared using three kinds of starting materials. It shows that the starting materials have an obvious effect on the impurity phases in final superconducting tapes. Compared with the other samples, the samples fabricated by SmAs, FeO, Fe2As, and SmF3 have the smallest arsenide impurity phase and voids. As a result, these samples possess much denser structure and better grain connectivity. Moreover, among the three kinds of samples fabricated in this work, this kind of sample has the highest zero-resistivity temperature ~40 K and largest critical current density ~4600 A/cm^2 in self-field at 4.2 K. This is the highest Jc values reported so far for SmFeAsO1-xFx wires and tapes.

cond-mat.supr-con↗

arXiv2011

High transport critical current densities in textured Fe-sheathed Sr1-xKxFe2As2+Sn superconducting tapes

We report the realization of grain alignment in Sn-added Sr1-xKxFe2As2 superconducting tapes prepared by ex-situ powder-in-tube method. At 4.2 K, high transport critical current densities Jc of 2.5x10^4 A/cm^2 (Ic = 180 A) in self-field and 3.5x10^3 A/cm^2 (Ic = 25.5 A) in 10 T have been measured. These values are the highest ever reported so far for Fe-based superconducting wires and tapes. We believe the superior Jc in our tape samples are due to well textured grains and strengthened intergrain coupling achieved by Sn addition. Our results demonstrated an encouraging prospect for application of iron based superconductors.

cond-mat.supr-con↗

arXiv2011

Synthesis and properties of La-doped CaFe2As2 single crystals with Tc = 42.7 K

Large single crystals of La-doped CaFe2As2 were successfully synthesized by the FeAs self-flux method. The x-ray diffraction patterns suggest high crystalline quality and c-axis orientation. By substitution of trivalent La3+ ions for divalent Ca2+, the resistivity anomaly in the parent compound CaFe2As2 is completely suppressed and a superconducting transition reaches the value of 42.7 K, which is higher than that of about 30 K reported in Saha S. R. et al., arXiv:1105.4798v1. The upper critical field has been determined with the magnetic field along ab-plane and c-axis, yielding an anisotropy of about 3.3.

cond-mat.supr-con↗

arXiv2011

Transport properties and anisotropy in rare earth doped CaFe2As2 single crystals with Tc above 40 K

In this paper we report the superconductivity above 40 K in the electron doping single crystal Ca1-xRexFe2As2 (Re = La, Ce, Pr). The x-ray diffraction patterns indicate high crystalline quality and c-axis orientation. the resistivity anomaly in the parent compound CaFe2As2 is completely suppressed by partial replacement of Ca by rare earth and a superconducting transition reaches as high as 43 K, which is higher than the value in electron doping FeAs-122 compounds by substituting Fe ions with transition metal, even surpasses the highest values observed in hole doping systems with a transition temperature up to 38 K. The upper critical field has been determined with the magnetic field along ab-plane and c-axis, yielding the anisotropy of 2~3. Hall-effect measurements indicate that the conduction in this material is dominated by electron like charge carriers. Our results explicitly demonstrate the feasibility of inducing superconductivity in Ca122 compounds via electron doping using aliovalent rare earth substitution into the alkaline earth site, which should add more ingredients to the underlying physics of the iron-based superconductors.

cond-mat.supr-con↗

arXiv2011

Direct observation of nanometer-scale amorphous layers and oxide crystallites at grain boundaries in polycrystalline Sr1-xKxFe2As2 superconductors

We report here an atomic resolution study of the structure and composition of the grain boundaries in polycrystalline Sr0.6K0.4Fe2As2 superconductor. A large fraction of grain boundaries contain amorphous layers larger than the coherence length, while some others contain nanometer-scale particles sandwiched in between amorphous layers. We also find that there is significant oxygen enrichment at the grain boundaries. Such results explain the relatively low transport critical current density (Jc) of polycrystalline samples with respect to that of bicrystal films.

cond-mat.supr-con↗