arXiv subjects

Young-Han Nam

Publications and source records attributed to Young-Han Nam.

11 recordsLinked to original sources

arXiv2026

Extreme-MIMO Field Trials in 7 GHz Band: Unlocking the Potential of New Spectrum for 6G

The frequency range around 7 GHz has emerged as a promising upper mid-band spectrum for 6th generation (6G), offering a practical balance between coverage and capacity. To fully exploit this band, however, future systems require substantially stronger beamforming and spatial multiplexing capability than today's 5G 64-port commercial deployments. This article investigates extreme multiple-input multiple-output (X-MIMO) with 256 digital ports as a practical 6G architecture for 7 GHz operation. First, through system-level simulations, we examine the throughput benefits and design trade-offs of increasing the number of base station (BS) and user equipment (UE) digital antenna ports, including comparisons between 128-port and 256-port configurations. We then present a 256-port 7 GHz BS and UE prototype and report field-trial results obtained in urban outdoor environments. The measurements demonstrate the feasibility of 8-layer downlink single-user MIMO over a 100 MHz bandwidth, achieving more than 3 Gbps for a single user under urban outdoor propagation conditions. Channel analysis based on measured data further suggests how the large digital aperture of X-MIMO supports high-order spatial multiplexing even with limited dominant angular clusters. Finally, we identify key challenges and outline research directions toward practical deployment of 7 GHz X-MIMO systems for 6G.

eess.SP↗

arXiv2025

Joint Phase Time Array: Opportunities, Challenges and System Design Considerations

This paper presents a novel approach to designing millimeter-wave (mmWave) cellular communication systems, based on joint phase time array (JPTA) radio frequency (RF) frontend architecture. JPTA architecture comprises time-delay components appended to conventional phase shifters, which offer extra degrees of freedom to be exploited for designing frequency-selective analog beams. Hence, a mmWave device equipped with JPTA can receive and transmit signals in multiple directions in a single time slot per RF chain, one direction per frequency subband, which alleviates the traditional constraint of one analog beam per transceiver chain per time slot. The utilization of subband-specific analog beams offers a new opportunity in designing mmWave systems, allowing for enhanced cell capacity and reduced pilot overhead. To understand the practical feasibility of JPTA, a few challenges and system design considerations are discussed in relation to the performance and complexity of the JPTA systems. For example, frequency-selective beam gain losses are present for the subband analog beams, e.g., up to 1 dB losses for 2 subband cases, even with the state-of-the-art JPTA delay and phase optimization methods. Despite these side effects, system-level analysis reveals that the JPTA system is capable of improving cell capacity: 5-percentile cell throughput by up to 65 per cent. To the best of the author's knowledge, this paper is the first paper explaining the system-level benefits and system-design challenges of JPTA, with an analysis of the performance tradeoff based on an intuitive metric of beam gain losses.

eess.SP↗

arXiv2024

Ultra-Wideband Double-Directional Channel Measurements and Statistical Modeling in Urban Microcellular Environments for the Upper-Midband/FR3

The upper midband, designated as Frequency Range 3 (FR3), is increasingly critical for the next-generation of wireless networks. Channel propagation measurements and their statistical analysis are essential first steps towards this direction. This paper presents a comprehensive ultra-wideband (UWB) double-directional channel measurement campaign in a large portion of FR3 (6-14 GHz) for urban microcellular environments. We analyze over 25,000 directional power delay profiles and providing key insights into line-of-sight (LoS) and obstructed line-of-sight (OLoS) conditions. This is followed by statistical modeling of path loss, shadowing, delay spread and angular spread. As the first UWB double-directional measurement campaign in this frequency range, this work offers critical insights for spectrum allocation, channel modeling, and the design of advanced communication systems, paving the way for further exploration of FR3.

eess.SY↗

arXiv2024

An Ultra-Wideband Study of Vegetation Impact on Upper Midband / FR3 Communication

Growing demand for high data rates is driving interest in the upper mid-band (FR 3) spectrum (6-24 GHz). While some propagation measurements exist in literature, the impact of vegetation on link performance remains under-explored. This study examines vegetation-induced losses in an urban scenario across 6-18 GHz. A simple method for calculating vegetation depth is introduced, along with a model that quantifies additional attenuation based on vegetation depth and frequency, divided into 1 GHz sub-bands. We see that excess vegetation loss increases with vegetation depth and higher frequencies. These findings provide insights for designing reliable, foliage-aware communication networks in FR 3.

eess.SP↗

arXiv2019

A Tutorial on UAVs for Wireless Networks: Applications, Challenges, and Open Problems

The use of flying platforms such as unmanned aerial vehicles (UAVs), popularly known as drones, is rapidly growing. In particular, with their inherent attributes such as mobility, flexibility, and adaptive altitude, UAVs admit several key potential applications in wireless systems. On the one hand, UAVs can be used as aerial base stations to enhance coverage, capacity, reliability, and energy efficiency of wireless networks. On the other hand, UAVs can operate as flying mobile terminals within a cellular network. Such cellular-connected UAVs can enable several applications ranging from real-time video streaming to item delivery. In this paper, a comprehensive tutorial on the potential benefits and applications of UAVs in wireless communications is presented. Moreover, the important challenges and the fundamental tradeoffs in UAV-enabled wireless networks are thoroughly investigated. In particular, the key UAV challenges such as three-dimensional deployment, performance analysis, channel modeling, and energy efficiency are explored along with representative results. Then, open problems and potential research directions pertaining to UAV communications are introduced. Finally, various analytical frameworks and mathematical tools such as optimization theory, machine learning, stochastic geometry, transport theory, and game theory are described. The use of such tools for addressing unique UAV problems is also presented. In a nutshell, this tutorial provides key guidelines on how to analyze, optimize, and design UAV-based wireless communication systems.

cs.IT↗

arXiv2017

Distributed FD-MIMO: Cellular Evolution for 5G and Beyond

This paper presents the next evolution of FD-MIMO technology for beyond 5G, where antennas of the FD-MIMO system are placed in a distributed manner throughout the cell in a multi-cell deployment scenario. This system, referred to as Distributed FD-MIMO (D-FD-MIMO) system, is capable of providing higher cell average throughput as well as more uniform user experience compared to the conventional FD-MIMO system. System level simulations are performed to evaluate performance. Our results show that the proposed D-FD-MIMO system achieves 1.4-2 times cell average throughput gain compared to the FD-MIMO system. The insights of performance gain are provided. Hardware implementation challenges and potential standards impact are also presented.

cs.IT↗

arXiv2016

Initial Beam Association in Millimeter Wave Cellular Systems: Analysis and Design Insights

Enabling the high data rates of millimeter wave (mmWave) cellular systems requires deploying large antenna arrays at both the basestations and mobile users. The beamforming weights of these large arrays need to be tuned to guarantee sufficient beamforming gains. Prior work on coverage and rate of mmWave cellular networks focused mainly on the case when basestations and mobile users beamfomring vectors are perfectly designed for maximum beamforming gains. Designing beamforming/combining vectors, though, requires training which may impact both the SINR coverage and rate of mmWave cellular systems. This paper characterizes and evaluates the performance of mmWave cellular networks while accounting for the beam training/association overhead. First, a model for the initial beam association is developed based on beam sweeping and downlink control pilot reuse. To incorporate the impact of beam training into system performance, a new metric, called the effective reliable rate, is defined and adopted. Using stochastic geometry, the effective reliable rate of mmWave cellular networks is derived for two special cases: with near-orthogonal control pilots and with full pilot reuse. Analytical and simulation results provide insights into the answers of three important questions: (i) What is the impact of beam association on mmWave network performance? (ii) Should orthogonal or reused control pilots be employed in the initial beam association phase? (iii) Should exhaustive or hierarchical search be adopted for the beam training phase? The results show that unless the employed beams are very wide or the system coherence block length is very small, exhaustive search with full pilot reuse is nearly as good as perfect beam alignment.

cs.IT↗

arXiv2016

Massive MIMO Combining with Switches

Massive multiple-input multiple-output (MIMO) is expected to play a central role in future wireless systems. The deployment of large antenna arrays at the base station and the mobile users offers multiplexing and beamforming gains that boost system spectral efficiency. Unfortunately, the high cost and power consumption of components like analog-to-digital converters makes assigning an RF chain per antenna and applying typical fully digital precoding/combining solutions difficult. In this paper, a novel architecture for massive MIMO receivers, consisting of arrays of switches and constant (non-tunable) phase shifters, is proposed. This architecture applies a quasi-coherent combining in the RF domain to reduce the number of required RF chains. An algorithm that designs the RF combining for this architecture is developed and analyzed. Results show that the proposed massive MIMO combining model can achieve a comparable performance to the fully-digital receiver architecture in single-user and multi-user massive MIMO setups.

cs.IT↗

arXiv2015

3D Channel Model in 3GPP

Multi-antenna techniques capable of exploiting the elevation dimension are anticipated to be an important air-interface enhancement targeted to handle the expected growth in mobile traffic. In order to enable the development and evaluation of such multi-antenna techniques, the 3rd generation partnership project (3GPP) has recently developed a 3-dimensional (3D) channel model. The existing 2-dimensional (2D) channel models do not capture the elevation channel characteristics lending them insufficient for such studies. This article describes the main components of the newly developed 3D channel model and the motivations behind introducing them. One key aspect is the ability to model channels for users located on different floors of a building (at different heights). This is achieved by capturing a user height dependency in modelling some channel characteristics including pathloss, line-of-sight (LOS) probability, etc. In general this 3D channel model follows the framework of WINNERII/WINNER+ while also extending the applicability and the accuracy of the model by introducing some height and distance dependent elevation related parameters.

cs.IT↗

arXiv2006

On the Error Exponents of ARQ Channels with Deadlines

We consider communication over Automatic Repeat reQuest (ARQ) memoryless channels with deadlines. In particular, an upper bound L is imposed on the maximum number of ARQ transmission rounds. In this setup, it is shown that incremental redundancy ARQ outperforms Forney's memoryless decoding in terms of the achievable error exponents.

cs.IT↗

arXiv2006

ARQ Diversity in Fading Random Access Channels

A cross-layer optimization approach is adopted for the design of symmetric random access wireless systems. Instead of the traditional collision model, a more realistic physical layer model is considered. Based on this model, an Incremental Redundancy Automatic Repeat reQuest (IR-ARQ) scheme, tailored to jointly combat the effects of collisions, multi-path fading, and additive noise, is developed. The Diversity-Multiplexing-Delay tradeoff (DMDT) of the proposed scheme is analyzed for fully-loaded queues, and compared with that of Gallager tree algorithm for collision resolution and the network-assisted diversity multiple access (NDMA) protocol of Tsatsanis et al.. The fully-loaded queue model is then replaced by one with random arrivals, under which these protocols are compared in terms of the stability region, average delay and diversity gain. Overall, our analytical and numerical results establish the superiority of the proposed IR-ARQ scheme and reveal some important insights. For example, it turns out that the performance is optimized, for a given total throughput, by maximizing the probability that a certain user sends a new packet and minimizing the transmission rate employed by each user.

cs.IT↗