arXiv subjects

Yu-Hao Deng

Publications and source records attributed to Yu-Hao Deng.

At least 19 recordsLinked to original sources

arXiv2026

Fast Nondestructive Readout for High-Clock-Rate Atom Array Quantum Processor

Neutral-atom arrays have rapidly advanced to support thousands of qubits and execute high-fidelity logical operations. However, these processors remain severely throttled by their slowest fundamental operation: nondestructive qubit measurement, which requires milliseconds and fundamentally limits the system's clock rate. This bottleneck arises from both an inherent photon-budget dilemma---sufficient fluorescence for reliable state discrimination must be collected without excessive heating or loss---and frame-based imaging, which imposes one common exposure and decision latency on intrinsically independent, site-local measurements. Here, we overcome these limitations with a fast, nondestructive readout architecture based on real-time, site-resolved adaptive protection. By integrating continuous photon counting with a dynamic feedforward framework, we decode qubit states with sub-microsecond latency and instantly shield atoms from redundant scattering. Demonstrated in parallel across a 100-qubit reconfigurable atom array, with adaptive protection on a 25-site subarray, this dynamic decision protocol reduces the average probe time to just $15\ μ\text{s}$. Model-free benchmarking yields a discrimination infidelity of $4.1 \times 10^{-5}$ and an atom loss of $2.1 \times 10^{-4}$, simultaneously setting new performance records for atom arrays. Exploiting this capability, we operate repeated quantum circuits at an unprecedented 1.7 kHz clock rate with atoms reused over 120 consecutive rounds---nearly sevenfold higher than the previous record---and enter the sub-millisecond cycle regime for the first time. By removing nondestructive readout as the dominant cycle-time bottleneck, this work unlocks high-clock-rate mid-circuit syndrome extraction, paving the way for high-throughput, fault-tolerant quantum computation.

quant-ph↗

arXiv2026

Squeezed-slit Bohr-Einstein Interferometer

The Einstein-Bohr recoiling-slit gedankenexperiment, a cornerstone of quantum complementarity, has long been constrained by the zero-point fluctuations of the atomic slit -- the spatial Standard Quantum Limit (SQL). Here we transcend this fundamental boundary through active quantum state engineering of a single-atom slit. By implementing a non-adiabatic quench-evolve-quench protocol, we prepare the atomic motion in a squeezed state, dynamically redistributing phase-space uncertainty to suppress which-path information and restore high-visibility interference beyond the static vacuum limit. We report an intrinsic visibility of $0.938_{-0.008}^{+0.004}$, violating the SQL ($0.819$) by over 10 standard deviations, corresponding to $7.6(2)$ dB of effective squeezing. Our work reveals Kerr-induced non-Gaussian dynamics and reinterprets the traditional interferometer as a powerful tool for continuous-variable Wigner tomography, bridging the gap between quantum foundations and advanced metrology.

quant-ph↗

arXiv2026

Taming Rydberg Decay with Measurement-based Quantum Computation

Programmable neutral atom arrays show great promise for fault-tolerant quantum computing. A dominant physical error on this platform is qubit leakage and loss, notably decay errors from the Rydberg state during two-qubit gates. Such leakage events are particularly detrimental as they propagate, generating correlated errors that severely degrade the effective error distance of quantum error correction codes. Here, we present a novel approach to address Rydberg decay errors leveraging measurement-based quantum computation (MBQC). Our scheme strategically exploits the inherent geometric structure of topological cluster states and only uses final leakage detection information to locate propagated errors originating from Rydberg decay. This eliminates the need for complex and atom-species-specific mid-circuit leakage detection, offering broader applicability, e.g., to the well-established Rb atom platform. We demonstrate a high error threshold of 3.65\% per CZ gate for pure Rydberg decay and achieve a favorable error distance $d_e \approx d$. Our method compares favorably with state-of-the-art erasure conversion protocols in the sub-threshold performance, offering comparable or marginally larger logical error rates while significantly reducing experimental overhead.

quant-ph↗

arXiv2026

Locating Rydberg Decay Error in SWAP-Leakage Reduction Circuit Protocol

Qubit leakage and loss, particularly Rydberg-induced decay during two-qubit gates, pose significant challenges to fault-tolerant quantum computing with neutral atom arrays, as they propagate to correlated errors and degrade code distance. Here, we present a hardware-efficient scheme for addressing Rydberg decay using the SWAP-Leakage Reduction Circuit (SWAP-LRC) protocol, which leverages ancilla-data qubit swaps for in-line leakage mitigation. This strategy eliminates the need for atom-species-specific mid-circuit detection or additional ancillary qubits. Based on experimental detection capabilities, we present two specialized decoders. For detectable leakage/loss (e.g., in $^{171}$Yb), our Located Decoder achieves a high threshold of 2.33\% per CNOT gate and an improved error distance, significantly outperforming conventional Pauli error models. More interestingly, for scenarios where only one error type is detectable (e.g., atom loss for $^{87}$Rb), our Critical Decoder specifically targets and mitigates the most detrimental critical faults caused by correlated leakage, achieving an error distance comparable to standard Pauli errors. Our findings offer insights for handling complex non-Pauli errors for neutral atom quantum computation.

quant-ph↗

arXiv2026

Sustaining high-fidelity quantum logic in neutral-atom circuits via mid-circuit operations

The realization of fault-tolerant quantum computation hinges on the ability to execute deep quantum circuits while maintaining gate fidelities consistently above error-correction thresholds. Although neutral-atom arrays have recently demonstrated high-fidelity two-qubit gates and early-stage logical quantum processors, sustaining such high performance across deep, repetitive circuits remains a formidable challenge due to cumulative motional heating and atom loss. Here we demonstrate a sustainable neutral-atom framework that overcomes these limitations by integrating a suite of hardware-efficient mid-circuit operations. We report a two-qubit controlled logic gate with a raw fidelity of 99.60(1)%, which is further increased to a fidelity of 99.81(1)% via non-destructive erasure detection. Crucially, by implementing in-circuit Raman sideband cooling and qubit re-initialization, we demonstrate that gate fidelities can be maintained at the ~99.8% level across multiple operational rounds without observable degradation. By actively managing the internal and motional entropy of the system mid-stream, our in-situ refreshable architecture provides a critical pathway for executing the repeated syndrome-extraction cycles required for large-scale, continuous quantum error correction.

quant-ph↗

arXiv2025

Robust quantum computational advantage with programmable 3050-photon Gaussian boson sampling

The creation of large-scale, high-fidelity quantum computers is not only a fundamental scientific endeavour in itself, but also provides increasingly robust proofs of quantum computational advantage (QCA) in the presence of unavoidable noise and the dynamic competition with classical algorithm improvements. To overcome the biggest challenge of photon-based QCA experiments, photon loss, we report new Gaussian boson sampling (GBS) experiments with 1024 high-efficiency squeezed states injected into a hybrid spatial-temporal encoded, 8176-mode, programmable photonic quantum processor, Jiuzhang 4.0, which produces up to 3050 photon detection events. Our experimental results outperform all classical spoofing algorithms, particularly the matrix product state (MPS) method, which was recently proposed to utilise photon loss to reduce the classical simulation complexity of GBS. Using the state-of-the-art MPS algorithm on the most powerful supercomputer EI Capitan, it would take > $10^{42}$ years to construct the required tensor network for simulation, while our Jiuzhang 4.0 quantum computer takes 25.6 $μ$s to produce a sample. This work establishes a new frontier of QCA and paves the way to fault-tolerant photonic quantum computing hardware.

quant-ph↗

arXiv2025

Enhanced Image Recognition Using Gaussian Boson Sampling

Gaussian boson sampling (GBS) has emerged as a promising quantum computing paradigm, demonstrating its potential in various applications. However, most existing works focus on theoretical aspects or simple tasks, with limited exploration of its capabilities in solving real-world practical problems. In this work, we propose a novel GBS-based image recognition scheme inspired by extreme learning machine (ELM) to enhance the performance of perceptron and implement it using our latest GBS device, Jiuzhang. Our approach utilizes an 8176-mode temporal-spatial hybrid encoding photonic processor, achieving approximately 2200 average photon clicks in the quantum computational advantage regime. We apply this scheme to classify images from the MNIST and Fashion-MNIST datasets, achieving a testing accuracy of 95.86% on MNIST and 85.95% on Fashion-MNIST. These results surpass those of classical method SVC with linear kernel and previous physical ELM-based experiments. Additionally, we explore the influence of three hyperparameters and the efficiency of GBS in our experiments. This work not only demonstrates the potential of GBS in real-world machine learning applications but also aims to inspire further advancements in powerful machine learning schemes utilizing GBS technology.

quant-ph↗

arXiv2024

A silicon photonics waveguide-coupled colloidal quantum dot photodiode sensitive beyond 1.6 um

Silicon photonics faces a persistent challenge in extending photodetection capabilities beyond the 1.6 um wavelength range, primarily due to the lack of appropriate epitaxial materials. Colloidal quantum dots (QDs) present a promising solution here, offering distinct advantages such as infrared wavelength tunability, cost-effectiveness, and facile deposition. Their unique properties position them as a potential candidate for enabling photodetection in silicon photonics beyond the conventional telecom wavelength, thereby expanding the potential applications and capabilities within this domain. In this study, we have successfully integrated lead sulfide (PbS) colloidal quantum dot photodiodes (QDPDs) onto silicon waveguides using standard process techniques. The integrated photodiodes exhibit a remarkable responsivity of 1.3 A/W (with an external quantum efficiency of 74.8%) at a wavelength of 2.1 um, a low dark current of only 106 nA and a bandwidth of 1.1 MHz under a -3 V bias. To demonstrate the scalability of our integration approach, we have developed a compact 8-channel spectrometer incorporating an array of QDPDs. This achievement marks a significant step toward realizing a cost-effective photodetector solution for silicon photonics, particularly tailored for a wide range of sensing applications around the 2 um wavelength range.

physics.optics↗

arXiv2024

Analysis of misidentifications in TEM characterization of perovskite material

Organic-inorganic hybrid perovskites (OIHPs) have recently emerged as groundbreaking semiconductor materials owing to their remarkable properties. Transmission electron microscopy (TEM), as a very powerful characterization tool, has been widely used in perovskite materials for structural analysis and phase identification. However, the perovskites are highly sensitive to electron beams and easily decompose into PbX2 (X= I, Br, Cl) and metallic Pb. The electron dose of general high-resolution TEM is much higher than the critical dose of MAPbI3, which results in universal misidentifications that PbI2 and Pb are incorrectly labeled as perovskite. The widely existed mistakes have negatively affected the development of perovskite research fields. Here misidentifications of the best-known MAPbI3 perovskite are summarized and corrected, then the causes of mistakes are classified and ascertained. Above all, a solid method for phase identification and practical strategies to reduce the radiation damage for perovskite materials have also been proposed. This review aims to provide the causes of mistakes and avoid misinterpretations in perovskite research fields in the future.

cond-mat.mtrl-sci↗

arXiv2024

Identifying and understanding the positive impact of defects for perovskites optoelectronic devices

Defects are generally regarded to have negative impacts on carrier recombination, charge-transport and ion migration in materials, which thus lower the efficiency, speed and stability of optoelectronic devices. Meanwhile, lots of efforts which focused on minimizing defects have greatly improved the performances of devices. Then, can defects be positive in optoelectronic devices? Herein, relying on in-depth understanding of defect-associated effects in semiconductors, trapping of photo-generated carriers by defects is applied to enlarge photoconductive gain in photodetection. Therefore, the record photoconductive gain, gain-bandwidth product and detection limit were achieved in this photodetector. Exceeding the general concept that defects are harmful, we identify a new view that the defects can be positive in photodetection, which may guide us to design high-performance photodetectors.

physics.app-ph↗

arXiv2023

Gaussian Boson Sampling with Pseudo-Photon-Number Resolving Detectors and Quantum Computational Advantage

We report new Gaussian boson sampling experiments with pseudo-photon-number-resolving detection, which register up to 255 photon-click events. We consider partial photon distinguishability and develop a more complete model for the characterization of the noisy Gaussian boson sampling. In the quantum computational advantage regime, we use Bayesian tests and correlation function analysis to validate the samples against all current classical mockups. Estimating with the best classical algorithms to date, generating a single ideal sample from the same distribution on the supercomputer Frontier would take ~ 600 years using exact methods, whereas our quantum computer, Jiuzhang 3.0, takes only 1.27 us to produce a sample. Generating the hardest sample from the experiment using an exact algorithm would take Frontier ~ 3.1*10^10 years.

quant-ph↗

arXiv2023

Solving Graph Problems Using Gaussian Boson Sampling

Gaussian boson sampling (GBS) is not only a feasible protocol for demonstrating quantum computational advantage, but also mathematically associated with certain graph-related and quantum chemistry problems. In particular, it is proposed that the generated samples from the GBS could be harnessed to enhance the classical stochastic algorithms in searching some graph features. Here, we use Jiuzhang, a noisy intermediate-scale quantum computer, to solve graph problems. The samples are generated from a 144-mode fully-connected photonic processor, with photon-click up to 80 in the quantum computational advantage regime. We investigate the open question of whether the GBS enhancement over the classical stochastic algorithms persists -- and how it scales -- with an increasing system size on noisy quantum devices in the computationally interesting regime. We experimentally observe the presence of GBS enhancement with large photon-click number and a robustness of the enhancement under certain noise. Our work is a step toward testing real-world problems using the existing noisy intermediate-scale quantum computers, and hopes to stimulate the development of more efficient classical and quantum-inspired algorithms.

quant-ph↗

arXiv2023

Unconditional and robust quantum metrological advantage beyond NOON states

Quantum metrology employs quantum resources to enhance the measurement sensitivity beyond that can be achieved classically. While multi-photon entangled NOON states can in principle beat the shot-noise limit and reach the Heisenberg limit, high NOON states are difficult to prepare and fragile to photon loss which hinders it from reaching unconditional quantum metrological advantages. Here, we combine the idea of unconventional nonlinear interferometers and stimulated emission of squeezed light, previously developed for photonic quantum computer Jiuzhang, to propose and realize a new scheme that achieves a scalable, unconditional, and robust quantum metrological advantage. We observe a 5.8(1)-fold enhancement above the shot-noise limit in the Fisher information extracted per photon, without discounting for photon loss and imperfections, which outperforms ideal 5-NOON states. The Heisenberg-limited scaling, the robustness to external photon loss, and the ease-to-use of our method make it applicable in practical quantum metrology at low photon flux regime.

quant-ph↗

arXiv2021

Phase-Programmable Gaussian Boson Sampling Using Stimulated Squeezed Light

The tantalizing promise of quantum computational speedup in solving certain problems has been strongly supported by recent experimental evidence from a high-fidelity 53-qubit superconducting processor1 and Gaussian boson sampling (GBS) with up to 76 detected photons. Analogous to the increasingly sophisticated Bell tests that continued to refute local hidden variable theories, quantum computational advantage tests are expected to provide increasingly compelling experimental evidence against the Extended Church-Turing thesis. In this direction, continued competition between upgraded quantum hardware and improved classical simulations is required. Here, we report a new GBS experiment that produces up to 113 detection events out of a 144-mode photonic circuit. We develop a new high-brightness and scalable quantum light source, exploring the idea of stimulated squeezed photons, which has simultaneously near-unity purity and efficiency. This GBS is programmable by tuning the phase of the input squeezed states. We demonstrate a new method to efficiently validate the samples by inferring from computationally friendly subsystems, which rules out hypotheses including distinguishable photons and thermal states. We show that our noisy GBS experiment passes the nonclassicality test using an inequality, and we reveal non-trivial genuine high-order correlation in the GBS samples, which are evidence of robustness against possible classical simulation schemes. The photonic quantum computer, Jiuzhang 2.0, yields a Hilbert space dimension up to $10^{43}$, and a sampling rate $10^{24}$ faster than using brute-force simulation on supercomputers.

quant-ph↗

arXiv2020

Alerts in High-resolution TEM characterization of perovskite material

High-resolution TEM (HRTEM) is a powerful tool for structure characterization. However, methylammonium lead iodide (MAPbI3) perovskite is highly sensitive to electron beams and easily decompose into lead iodide (PbI2). Universal misidentifications that PbI2 is incorrectly labeled as perovskite are widely exist in HRTEM characterization, which would negatively affect the development of perovskite research field. Here misidentifications in MAPbI3 perovskite calibration are summarized, classified and corrected based on corresponding electron diffraction (ED) simulations. Corresponding crystallographic parameters of intrinsic tetragonal MAPbI3 and the confusable hexagonal PbI2 are also presented clearly. Finally, the method of proper phase identification and some ways to control the radiation damage in HRTEM are provided. This work paves the way to avoid misleadings in HRTEM characterization of perovskite and other electron beam-sensitive materials in the future.

cond-mat.mtrl-sci↗

arXiv2020

Quantum computational advantage using photons

Gaussian boson sampling exploits squeezed states to provide a highly efficient way to demonstrate quantum computational advantage. We perform experiments with 50 input single-mode squeezed states with high indistinguishability and squeezing parameters, which are fed into a 100-mode ultralow-loss interferometer with full connectivity and random transformation, and sampled using 100 high-efficiency single-photon detectors. The whole optical set-up is phase-locked to maintain a high coherence between the superposition of all photon number states. We observe up to 76 output photon-clicks, which yield an output state space dimension of $10^{30}$ and a sampling rate that is $10^{14}$ faster than using the state-of-the-art simulation strategy and supercomputers. The obtained samples are validated against various hypotheses including using thermal states, distinguishable photons, and uniform distribution.

quant-ph↗

arXiv2020

Transfer of large-scale perovskite single-crystalline thin films onto arbitrary substrates

Metal halide perovskites single-crystalline thin films (SCTFs) have recently emerged as promising materials for the next generation of optoelectronic devices due to their superior intrinsic properties. However, it is still challenging to transfer and integrate them with other functional materials for hybrid multilayer devices because of their substrate-dependent growth. Herein, a method that allows the SCTFs to be transferred with high quality onto arbitrary substrates has been reported. By introducing hydrophobic treatment to the growth substrates, the adhesion between SCTFs and growth substrates is reduced. Meanwhile, anti-solvent intercalation technique is used to peel off SCTFs from the growth substrates intactly. Finally, centimeter-scale perovskite SCTF has been successfully transferred to target substrate. This work opens up a new route to transfer large-scale perovskite SCTFs, providing a platform to widen the applications of perovskite SCTFs in large-scale hybrid multilayer optoelectronic devices.

physics.app-ph↗

arXiv2020

Transfer of graphene onto arbitrary substrates via sublimable carrier

Graphene, a monolayer of carbon atoms packed into a two-dimensional crystal structure, attracted intense attention owing to its unique structure and optical, electronic properties. Recent advances in chemical vapor deposition (CVD) have led to the batch production of high quality graphene on metal foils. However, further applications are required in the way these graphenes are transferred from their growth substrates onto the target substrate. Here, we report a sublimable carrier method that allows the graphene to be transferred with high quality onto arbitrary substrates, including semiconductor, metal and organic substrates. The intrinsic problems of the residue and environmentally unfriendly organic solvents have been solved due to the polymer-free process. Optical microscopy, scanning electron microscopy (SEM) and Raman spectroscopy demonstrate the high quality and clean surface of the transferred graphene. This work provides a new way of optimizing graphene transfer and widens the applications of graphene in large-scale 2D electronics.

cond-mat.mtrl-sci↗