arXiv subjects

Yurong He

Publications and source records attributed to Yurong He.

3 recordsLinked to original sources

arXiv2026

Hybrid Tribo/piezoelectic Electrospun Nanofibers for Energy Harvesting Enhancement in Flexible Electronics

Triboelectric nanogenerators or TENGs and piezoelectric nanogenerators or PENGs have emerged as promising platforms for harvesting mechanical energy and converting it into electrical energy for powering flexible electronic devices. However, the material selection and structure design of such hybrid nanogenerator, and mechanisms of energy output still remain challenges. In this work, electrospinning is employed for the fabrication of nanofibers, particularly polyvinylidene fluoride or PVDF based nanofibers, due to its capability to generate high beta phase contents that effectively increase the piezoelectric performance of the PVDF friction layer, thereby enhancing the overall electrical performance for flexible electronics by merging tribo-piezoelectric power. Furthermore, various concentrations carbon nanotubes or CNT or graphene nanosheets or GNS are individually incorporated into the PVDF solution as nanofillers or NF to enhance the piezoelectric responses of the PVDF based nanofibers. The introduction of nanofillers is found to not only alter the fiber diameter but also modify the surface roughness of the electrospun nanofibers, and thus, enhancing the triboelectric effect. In addition, the output performance of the fabricated nanogenerator is predominantly governed by the piezoelectric effect rather than triboelectric effect, as the electrical output shows a strong positive correlation with the beta phase content of PVDF based nanofibers: the highest beta phase content reached to 85.3 percent and consistently resulted in the optimal energy output of 1.133 watt per meter square. Notably, the power density achieved by the prototype device reaches to the level of watt/m2, representing a substantial improvement compared with that of the conventional TENGs or PENGs reported to date, providing expanded opportunities for flexible electronic devices

cond-mat.mtrl-sci↗

arXiv2025

Effects of rough walls on sheared annular centrifugal Rayleigh-B\'enard convection

In this study, we investigate the coupling effects of roughness and wall shear in an annular centrifugal Rayleigh-B\'enard convection (ACRBC) system, where two cylinders rotate with different angular velocities. Two-dimensional direct numerical simulations are conducted within a Rayleigh number range of $10^{6} \leq Ra \leq 10^{8}$, and the non-dimensional angular velocity difference ($\varOmega$), representing wall shear, varied from 0 to 1. The Prandtl number is fixed at $Pr = 4.3$, the inverse Rossby number at $Ro^{-1} = 20$, and the radius ratio at $\eta = 0.5$. The interaction between wall shear and roughness leads to distinct heat transfer behavior in different regimes. In the buoyancy-dominant regime, an increase in the non-dimensional angular velocity difference ($\varOmega$) significantly enhances heat transfer. However, as $\varOmega$ continues to rise, a sharp reduction in heat transfer is observed in the transitional regime. Beyond a critical value of $\varOmega$, the flow enters a shear-dominant regime, where heat transfer remains unchanged despite further increases in $\varOmega$.

physics.flu-dyn↗

arXiv2023

Direct numerical simulation of Taylor-Couette flow with vertical asymmetric rough walls

Direct numerical simulations are performed to explore the effects of rotating direction of the vertical asymmetric rough wall on the transport properties of Taylor-Couette (TC) flow up to a Taylor number of $\textit{Ta} = 2.39 \times 10^7$. It is shown that compared to the smooth wall, the rough wall with vertical asymmetric strips can enhance the dimensionless torque \textit{Nu}$_\omega$, and more importantly, at high \textit{Ta} clockwise rotation of the inner rough wall (the fluid is sheared by the steeper slope side of the strips) results in a significantly bigger torque enhancement as compared to the counter-clockwise rotation (the fluid is sheared by the smaller slope side of the strips) due to the larger convective contribution to the angular velocity flux, although the rotating direction has a negligible effect on the torque at low \textit{Ta}. The larger torque enhancement caused by the clockwise rotation of vertical asymmetric rough wall at high \textit{Ta} is then explained by the stronger coupling between the rough wall and the bulk due to the larger biased azimuthal velocity towards the rough wall at the mid-gap of TC system, the increased intensity of turbulence manifesting by larger Reynolds stress and thinner boundary layer, and the more significant contribution of the pressure force on the surface of rough wall to the torque.

physics.flu-dyn↗