arXiv subjects

Zhancheng Yao

Publications and source records attributed to Zhancheng Yao.

4 recordsLinked to original sources

arXiv2026

Millikelvin digital-to-analog converter for superconducting quantum processors

Scaling superconducting quantum processors is increasingly constrained by the wiring, heat load, and calibration overhead associated with delivering high-resolution analog signals from room temperature to qubits at millikelvin temperature. Here we demonstrate a superconducting digital-to-analog converter (DAC) integrated with high-coherence fluxonium qubits in a multi-chip module architecture. The DACs generate persistent analog flux signals for tuning qubit parameters and are programmed deterministically using single-flux-quantum (SFQ) pulses, providing a digital interface compatible with established SFQ routing and demultiplexing technologies. Operating at millikelvin temperature, the DACs enable in-situ tuning of fluxonium qubits without measurable degradation of qubit coherence. The presented device provides a static control primitive for flux-tunable qubits, enabling parameter homogenization and eliminating the need for individual room-temperature DC bias lines. These results establish SFQ-programmable millikelvin DACs as a building block for digitally controlled superconducting quantum processors.

quant-ph↗

arXiv2026

Reconfigurable Superconducting Quantum Circuits Enabled by Micro-Scale Liquid-Metal Interconnects

Modular architectures are a promising route toward scalable superconducting quantum processors, but finite fabrication yield and the lack of high quality temporary interconnects impose fundamental limitations on system size. Here, we demonstrate chip-scale liquid-metal interconnects that show promise for plug-and-play superconducting quantum circuits by enabling non-destructive module replacement while maintaining high microwave performance. Using gallium-based liquid metals, we realize high-quality inter-module signal and ground interconnects, comparable in performance to conventional coplanar waveguide resonators. We illustrate consistent device characteristics across three thermal cycles between room temperature and 15 mK, as well as the ability to reform superconducting connections following module replacement. A width-dependent resonance frequency shift reveals a significant kinetic inductance fraction, which we attribute to the presence of $β$-phase tantalum as confirmed by X-ray characterization. Finally, we investigate power-dependent loss mechanisms and observe high-power dissipative nonlinearities qualitatively consistent with a readout-power heating model. These results establish liquid metals as viable chip-scale interconnects for reconfigurable, modular superconducting quantum systems.

quant-ph↗

arXiv2024

Low-loss liquid metal interconnects for superconducting quantum circuits

Building a modular architecture with superconducting quantum computing chips is one of the means to achieve qubit scalability, allowing the screening, selection, replacement, and integration of individual qubit modules into large quantum systems. However, the nondestructive replacement of modules within a compact architecture remains a challenge. Liquid metals, specifically gallium alloys, can be alternatives to solid-state galvanic interconnects. This is motivated by their self-healing, self-aligning, and other desirable fluidic properties, potentially enabling the nondestructive replacement of modules at room temperatures, even after operating the entire system at millikelvin regimes. In this study, we present coplanar waveguide resonators (CPWRs) interconnected by gallium alloy droplets, achieving high internal quality factors up to nearly one million and demonstrating performance on par with the continuous solid-state CPWRs. Leveraging the desirable fluidic properties of gallium alloys at room temperature and their compact design, we envision a modular quantum system enabled by liquid metals.

physics.app-ph↗

arXiv2021

Analysis of a Casimir-driven Parametric Amplifier with Resilience to Casimir Pull-in for MEMS Single-Point Magnetic Gradiometry

The Casimir Force, a quantum mechanical effect, has been observed in several microelectromechanical systems (MEMS) platforms. Due to its extreme sensitivity to the separation of two objects, the Casimir Force has been proposed as an excellent avenue for quantum metrology. Practical application, however, is challenging due to attractive forces leading to stiction and failure of the device, called Casimir pull-in. In this work, we design and simulate a Casimir-driven metrology platform, where a time-delay based parametric amplification technique is developed to achieve a steady state and avoid pull-in. We apply the design to the detection of weak, low frequency, gradient magnetic fields, similar to those emanating from ionic currents in the heart and brain. Simulation parameters are selected from recent experimental platforms developed for Casimir metrology and magnetic gradiometry, both on MEMS platforms. While MEMS offer many advantages to such an application, the detected signal must typically be at the resonant frequency of the device, with diminished sensitivity in the low frequency regime of biomagnetic fields. Using a Casimir-drive parametric amplifier, we report a 10,000 fold improvement in the best-case resolution of MEMS single-point gradiometers, with a maximum sensitivity of 6 Hz/(pT/cm) at 1 Hz. The development of the proposed design has the potential to revolutionize metrology, and specifically may enable unshielded monitoring of biomagnetic fields in ambient conditions.

quant-ph↗