arXiv subjects

Zhaoyang Ming

Publications and source records attributed to Zhaoyang Ming.

6 recordsLinked to original sources

arXiv2026

A Dual-Band Reconfigurable Shared-Aperture Antenna Array With Independent Sub-6-GHz and Centimeter-Wave Beam Control

A planar dual-band reconfigurable shared-aperture antenna array is proposed for compact next-generation wireless front ends that require both sub-6-GHz and centimeter-wave (cm-wave) coverage. The array integrates a 2 by 2 sub-6-GHz microstrip dipole array and a 4 by 4 cm-wave stacked patch array within the same aperture, while providing independent beam control in the two bands without conventional T/R modules or beamforming networks. Slot-coupled feeding is employed to separate the radiating aperture from the reconfigurable RF feeding networks and DC bias circuits. PIN-diode-loaded split feeding rings first provide independent 1-bit phase reconfigurability for both bands. A compact reconfigurable $90^{\circ}$ phase shifter is then introduced as an additional phase-control stage, resulting in 2-bit phase control for sub-6 GHz elements and cm-wave subarrays. To reduce cross-band coupling in the compact shared aperture, a double-layer electromagnetic band-gap (EBG) structure is used to suppress cm-wave surface waves and higher-order sub-6-GHz modes excited by the cm-wave elements. A prototype is fabricated and measured. In the sub-6-GHz band, 11 reconfigurable radiation patterns are obtained, including two difference patterns and nine directional beams, with a peak broadside gain of 10.5 dBi. In the cm-wave band, two-dimensional beam scanning up to $\pm40^{\circ}$ is demonstrated with a peak gain of 14.6 dBi in both the E-plane and H-plane. These results show that the proposed architecture can combine dual-band shared-aperture integration and independent reconfigurable beam control in a compact antenna platform.

eess.SP↗

arXiv2026

Multiport Analytical Pixel Electromagnetic Simulator (MAPES) for AI-assisted RFIC and Microwave Circuit Design

This paper proposes a novel analytical framework, denoted the Multiport Analytical Pixel Electromagnetic Simulator (MAPES). MAPES enables efficient and accurate prediction of the electromagnetic (EM) performance of arbitrary pixel-based microwave (MW) and RFIC structures. Unlike the Internal Multiport Method (IMPM), which optimizes only connecting elements within a fixed, gap-separated pixel skeleton, MAPES operates directly on the all-pixel presence/absence formulation used in recent MW/RFIC design. This is enabled by diagonal virtual pixels, an occupancy-to-load mapping, and a multi-layer/via port-level formulation that have no counterpart in IMPM. By introducing virtual pixels and diagonal virtual pixels and inserting virtual ports at critical positions, MAPES captures all horizontal, vertical, and diagonal electromagnetic couplings within a single multiport impedance matrix. Only a small set of full-wave simulations (typically about 1% of the datasets required by AI-assisted EM emulators) is needed to construct this matrix. Subsequently, any arbitrary pixel configuration can be evaluated analytically using a closed-form multiport relation without additional full-wave calculations. The proposed approach eliminates data-driven overfitting and ensures accurate results across all design variations. Using MAPES, comprehensive examples for single- and double-layer PCBs and CMOS processes (180 nm and 65 nm) confirm that high prediction accuracy with 600-2000$\times$ speed improvement is achieved compared to CST simulations. Owing to its efficiency, scalability, and reliability, MAPES provides a practical and versatile tool for AI-assisted MW circuit and RFIC design across diverse fabrication technologies.

eess.SP↗

arXiv2026

Pixel-based Reconfigurable Beamforming Networks Emulating Physical Movement in FAS

The concept of Fluid Antenna Systems (FAS) has emerged as an attractive new system technology for use in sixth-generation (6G) wireless systems. However, most FAS implementations rely on mechanical antenna movement and thus are too slow to be useful. In this paper, a novel pixel-based reconfigurable beamforming network (PRBFN) is used to emulate movement in Fluid Antenna Systems (FASs). Using the insight that changing an antenna's physical position is equivalent to changing radiation patterns that satisfy the desired pattern correlation, the PRBFN is used to control the excitation current vectors of a multi-port antenna, thereby governing the pattern correlation. Key novelties of our work involve the selection of current vectors, and the methodology for scaling the PRBFN to realize large-aperture FAS. Results are provided for our PRBFN combined with an FAS (denoted as a PRBFN-FAS) when the equivalent physical movement is set to 1.5 wavelengths. Measurements demonstrate that the PRBFN-FAS provides the desired spatial correlation, including the Bessel function relation from Clarke's model across a 5\% bandwidth, satisfying FAS requirements. System-level experiments confirm the viability of the PRBFN-FAS in communication scenarios.

eess.SP↗

arXiv2025

A Hybrid Transmitting and Reflecting Beyond Diagonal Reconfigurable Intelligent Surface with Independent Beam Control and Power Splitting

A hybrid transmitting and reflecting beyond diagonal reconfigurable intelligent surface (BD-RIS) design is proposed. Operating in the same aperture, frequency band and polarization, the proposed BD-RIS features independent beam steering control of its reflected and transmitted waves. In addition it provides a hybrid mode with both reflected and transmitted waves using tunable power splitting between beams. The BD-RIS comprises two phase reconfigurable antenna arrays interconnected by an array of tunable two-port power splitters. The two-port power splitter in each BD-RIS cell is built upon a varactor in parallel with a bias inductor to exert tunable impedance variations on transmission lines. Provided with variable reverse DC voltages, the two-port power splitter can control the power ratio of S11 over S21 from -20 dB to 20 dB, thus allowing tunable power splitting. Each antenna is 2-bit phase reconfigurable with 200 MHz bandwidth at 2.4 GHz so that each cell of BD-RIS can also achieve independent reflection and transmission phase control. To characterize and optimize the electromagnetic response of the proposed BD-RIS design, a Thévenin equivalent model and corresponding analytical method is provided. A BD-RIS with 4 by 4 cells was also prototyped and tested. Experiments show that in reflection and transmission mode, the fabricated BD-RIS can realize beam steering in reflection and transmission space, respectively. It is also verified that when operating in hybrid mode, the BD-RIS enables independent beam steering of the reflected and transmitted waves. This work helps fill the gap between realizing practical hardware design and establishing an accurate physical model for the hybrid transmitting and reflecting BD-RIS, enabling hybrid transmitting and reflecting BD-RIS assisted wireless communications.

eess.SP↗

arXiv2024

A Pixel-based Reconfigurable Antenna Design for Fluid Antenna Systems

Fluid Antenna Systems (FASs) have recently been proposed for enhancing the performance of wireless communication. Previous antenna designs to meet the requirements of FAS have been based on mechanically movable or liquid antennas and therefore have limited reconfiguration speeds. In this paper, we propose a design for a pixel-based reconfigurable antenna (PRA) that meets the requirements of FAS and the required switching speed. It can provide 12 FAS ports across 1/2 wavelength and consists of an E-slot patch antenna and an upper reconfigurable pixel layer with 6 RF switches. Simulation and experimental results from a prototype operating at 2.5 GHz demonstrate that the design can meet the requirements of FAS including port correlation with matched impedance.

eess.SP↗

arXiv2024

A Shared-Aperture Dual-Band sub-6 GHz and mmWave Reconfigurable Intelligent Surface With Independent Operation

A novel dual-band reconfigurable intelligent surface (DBI-RIS) design that combines the functionalities of millimeter-wave (mmWave) and sub-6 GHz bands within a single aperture is proposed. This design aims to bridge the gap between current single-band reconfigurable intelligent surfaces (RISs) and wireless systems utilizing sub-6 GHz and mmWave bands that require RIS with independently reconfigurable dual-band operation. The mmWave element is realized by a double-layer patch antenna loaded with 1-bit phase shifters, providing two reconfigurable states. An 8x8 mmWave element array is selectively interconnected using three RF switches to form a reconfigurable sub-6 GHz element at 3.5 GHz. A suspended electromagnetic band gap (EBG) structure is proposed to suppress surface waves and ensure sufficient geometric space for the phase shifter and control networks in the mmWave element. A low-cost planar spiral inductor (PSI) is carefully optimized to connect mmWave elements, enabling the sub-6 GHz function without affecting mmWave operation. Finally, prototypes of the DBI-RIS are fabricated, and experimental verification is conducted using two separate measurement testbeds. The fabricated sub-6 GHz RIS successfully achieves beam steering within the range of -35 to 35 degrees for DBI-RIS with 4x4 sub-6 GHz elements, while the mmWave RIS demonstrates beam steering between -30 to 30 degrees for DBI-RIS with 8x8 mmWave elements, and have good agreement with simulation results.

eess.SP↗