arXiv subjects

Zhengyuan Xu

Publications and source records attributed to Zhengyuan Xu.

At least 19 recordsLinked to original sources

arXiv2024

Beacon-enabled TDMA Ultraviolet Communication Network System Design and Realization

Nonline of sight (NLOS) ultraviolet (UV) scattering communication can serve as a good candidate for outdoor optical wireless communication (OWC) in the cases of non-perfect transmitter-receiver alignment and radio silence. We design and demonstrate a NLOS UV scattering communication network system in this paper, where a beacon-enabled time division multiple access (TDMA) scheme is adopted. In our system, LED and PMT are employed for transmitter and receiver devices, repectivey. Furthermore, we design algorithms for beacon transmission, beacon reception, time compensation, and time slot transition for hardware realization in field-programmable gate array (FPGA) board based on master-slave structure, where master node periodically transmits beacon signals to slave nodes. Experimental results are provided to evaluate the time synchronization error and specify the system key parameters for real-time implementation. We perform field tests for real-time communication network with the transmission range over 110 multiplied by 90 square meters, where the system throughput reaches 800kbps.

eess.SY↗

arXiv2024

Ultraviolet Positioning via TDOA: Error Analysis and System Prototype

This work performs the design, real-time hardware realization, and experimental evaluation of a positioning system by ultra-violet (UV) communication under photon-level signal detection. The positioning is based on time-difference of arrival (TDOA) principle. Time division-based transmission of synchronization sequence from three transmitters with known positions is applied. We investigate the positioning error via decomposing it into two parts, the transmitter-side timing error and the receiver-side synchronization error. The theoretical average error matches well with the simulation results, which indicates that theoretical fitting can provide reliable guidance and prediction for hardware experiments. We also conduct real-time hardware realization of the TDOA-based positioning system using Field Programmable Gate Array (FPGA), which is experimentally evaluated via outdoor experiments. Experimental results match well with the theoretical and simulation results.

eess.SY↗

arXiv2023

InFi: End-to-End Learning to Filter Input for Resource-Efficiency in Mobile-Centric Inference

Mobile-centric AI applications have high requirements for resource-efficiency of model inference. Input filtering is a promising approach to eliminate the redundancy so as to reduce the cost of inference. Previous efforts have tailored effective solutions for many applications, but left two essential questions unanswered: (1) theoretical filterability of an inference workload to guide the application of input filtering techniques, thereby avoiding the trial-and-error cost for resource-constrained mobile applications; (2) robust discriminability of feature embedding to allow input filtering to be widely effective for diverse inference tasks and input content. To answer them, we first formalize the input filtering problem and theoretically compare the hypothesis complexity of inference models and input filters to understand the optimization potential. Then we propose the first end-to-end learnable input filtering framework that covers most state-of-the-art methods and surpasses them in feature embedding with robust discriminability. We design and implement InFi that supports six input modalities and multiple mobile-centric deployments. Comprehensive evaluations confirm our theoretical results and show that InFi outperforms strong baselines in applicability, accuracy, and efficiency. InFi achieve 8.5x throughput and save 95% bandwidth, while keeping over 90% accuracy, for a video analytics application on mobile platforms.

cs.AI↗

arXiv2023

Channel Estimation and Signal Detection for NLOS Ultraviolet Scattering Communication with Space Division Multiple Access

We design a receiver assembling several photomultipliers (PMTs) as an array to increase the field of view (FOV) of the receiver and adapt to multiuser situation over None-line-of-sight (NLOS) ultraviolet (UV) channels. Channel estimation and signal detection have been investigated according to the space division characteristics of the structure. Firstly, we adopt the balanced structure on the pilot matrix, analyze the channel estimation mean square error (MSE), and optimize the structure parameters. Then, with the estimated parameters, an analytical threshold detection rule is proposed as a preliminary work of multiuser detection. The detection rule can be optimized by analyzing the separability of two users based on the Gaussian approximation of Poisson weighted sum. To assess the effect of imperfect estimation, the sensitivity analysis of channel estimation error on two-user signal detection is performed. Moreover, we propose a successive elimination method for on-off keying (OOK) modulated multiuser symbol detection based on the previous threshold detection rule. A closed-form upper bound on the detection error rate is calculated, which turns out to be a good approximation of that of multiuser maximum-likelihood (ML) detection. The proposed successive elimination method is twenty times faster than the ML detection with negligible detection error rate degradation.

cs.IT↗

arXiv2022

Map-Assisted Constellation Design for mmWave WDM with OAM in Short-Range LOS Environment

We consider a system that integrates positioning and single-user millimeter wave (mmWave) communication, where the communication part adopts wavelength division multiplexing (WDM) and orbital angular momentum (OAM). This paper addresses the multi-dimensional constellation design in shortrange line-of-sight (LOS) environment, with stable communication links. We propose a map-assisted method to quantify the system parameters based on positions and reduce real-time computing overhead. We explore the possibility of using a few patterns in the maps, and investigate its performance loss. We first investigate the features of OAM beams, and find that the link gain ratio between any two sub-channels remains unchanged at some postions. Then, we prove that a fixed constellation can be adopted for the positions where the link gain matrices are sufficiently close to be proportional. Moreover, we prove that the system can adopt a fixed power vector to generate a multidimensional constellation if the difference between fixed power vector and optimal power vector is small. Finally, we figure out that the constellation design for all receiver locations can be represented by a few constellation sets.

cs.IT↗

arXiv2022

The design and optimization of synchronization sequence for Ultraviolet communication

In the ultraviolet (UV) scattering communication, the received signals exhibit the characteristics of discrete photoelectrons due to path loss. The synchronization is based on maximum Pulse Number-Sequence correlation problem. First of all, the accuracy of synchronization is vital to channel estimation and decoding. This article focuses on improving synchronization accuracy by designing and optimizing synchronization sequences. As for the maximum Pulse Number-Sequence correlation problem, it is assumed that the correlation values satisfy the Gaussian distribution and their mathematical expectation, variance and covariance are derived to express the upper bound of synchronization offset. The synchronization sequence we designed has two equilong RANDOM parts (Symbols meet Bernoulli distribution with equal probability.) and a $\{1,0,1,0,1,0,...,1,0,1,0\}$ part between them with $ α$ as its proportion of entire sequence. On the premise of ensuring the synchronization reliability, the synchronization deviation can be reduced by optimizing $ α$. There are simulation experiments to verify correctness of the derivation, reasonableness of the hypothesis and reliability of optimization. Compared with equilong random sequence, the synchronization accuracy of the optimized synchronization sequence is significantly improved.

eess.SP↗

arXiv2021

Hybrid RF/VLC Systems: A Comprehensive Survey on Network Topologies, Performance Analyses, Applications, and Future Directions

Wireless communications refer to data transmissions in unguided propagation media through the use of wireless carriers such as radio frequency (RF) and visible light (VL) waves. The rising demand for high data rates, especially, in indoor scenarios, overloads conventional RF technologies. Therefore, technologies such as millimeter waves (mmWave) and cognitive radios have been adopted as possible solutions to overcome the spectrum scarcity and capacity limitations of the conventional RF systems. In parallel, visible light communication (VLC) has been proposed as an alternative solution, where a light source is used for both illumination and data transmission. In comparison to RF links, VLC links present a very high bandwidth that allows much higher data rates. VLC exhibits also immunity to interference from electromagnetic sources, has unlicensed channels, is a very low power consumption system, and has no health hazard. VLC is appealing for a wide range of applications including reliable communications with low latency such as vehicle safety communication. Despite the major advantages of VLC technology and a variety of its applications, its use has been hampered by its cons such as its dependence on a line of sight connectivity. Recently, hybrid RF/VLC systems were proposed to take advantage of the high capacity of VLC links and better connectivity of RF links. Thus, hybrid RF/VLC systems are envisioned as a key enabler to improve the user rates and mobility on one hand and to optimize the capacity, interference and power consumption of the overall network on the other hand. This paper seeks to provide a detailed survey of hybrid RF/VLC systems. This paper represents an overview of the current developments in the hybrid RF/VLC systems, their benefits and limitations for both newcomers and expert researchers.

eess.SP↗

arXiv2021

Quantumized Microwave Detection Based on $Λ$-Type Three-level Superconducting System: HMM Modeling and Performance Prediction

We adopt artificial $Λ$-type three-level system with superconducting devices for microwave signal detection, where the signal intensity reaches the level of discrete photons instead of continuous waveform. Based on the state transition principles of the three-level system, we propose a statistical model for microwave signal detection. Moreover, we investigate the achievable transmission rate and signal detection based on the statistical model. It is predicted that the proposed detection can achieve significantly higher sensitivity compared with the currently deployed 4G/5G communication system. We further characterize the received signal considering the saturation phonomenon, which reveals negligible performance degradation caused by saturation under weak received power regime.

eess.SP↗

arXiv2021

Channel Modeling and Signal Processing for Array-based Visible Light Communication System in Misalignment

This paper proposes an indoor visible light communication (VLC) system with multiple transmitters and receivers. Due to diffusivity of LED light beams, photodiode receive signals from many directions. We use one concave and one convex lens as optical antenna, and obtain the optimal lens structure by optimizing which corresponds to the minimum condition number of channel gain matrix. In this way the light emitted by different LED can be separated well from each other then minimize signal interference. However, interference increases in the case of system deviation, so we explore the system mobility. Then subsequent signal processing is carried out, including signal combining and successive interference cancellation (SIC). We combine the same signal received by different receivers to improve signal to interference noise ratio (SINR). And SIC can effectively restore interference and eliminate its impact. The simulation results show that channel capacity can be increased by more than 5 times and up to 20 times under the condition of receiver and transmitter alignment. In the case of movement, channel capacity can also be increased by about 4 times on average. Moreover, the mobile range of system is also significantly expanded.

eess.SP↗

arXiv2020

Weak Radio Frequency Signal Detection Based on Piezo-Opto-Electro-Mechanical System: Architecture Design and Sensitivity Prediction

We propose a novel radio-frequency (RF) receiving architecture based on micro-electro-mechanical system (MEMS) and optical coherent detection module. The architecture converts the received electrical signal into mechanical vibration through the piezoelectric effect and adopts an optical detection module to detect the mechanical vibration. We analyze the response function of piezoelectric film to an RF signal, the noise limited sensitivity of the optical detection module and the system transfer function in the frequency domain. Finally, we adopt simple on-off keying (OOK) modulation with bandwidth 1 kHz and carrier frequency 1 GHz, to numerically evaluate the detection sensitivity. The result shows that, considering the main noise sources in wireless channel and circuits, the signal detection sensitivity can reach around -160 dBm with a 50 $Ω$ impedance. Such sensitivity significantly outperforms that of the currently deployed Long Term Evolution (LTE) system, when normalizing the transmission bandwidth also to 1 kHz.

eess.SP↗

arXiv2020

Automatic Gain Control Design for Dynamic Visible Light Communication Systems

For dynamic visible light communication (VLC) systems, received optical power fluctuates largely due to the fast movement of VLC terminals. Such fluctuations will cause possible signal clipping and quantization noise at the analog-to-digital converters (ADCs) and thus aggravate signal-to-noise ratio (SNR) and reliability of the communication link. To mitigate this effect, the automatic gain control (AGC) technique is often introduced in the receiver front-end to adaptively adjust the electrical signal strength. In this paper, we provided a VLC front-end analysis considering AGC model. Based on the model, some design principles of AGC are theoretically derivated: the effects of AGC index $m$, AGC maximum gain $g_{max}$ and AGC equilibrium range $DR$. Next, an analog AGC amplifier was carefully implemented and the effectiveness of our AGC modeling was proved through BER experiments. Finally, realtime 25Mb/s on-off-keying (OOK) experiments with AGC function were demonstrated in a dynamic link with different speeds. Experimental results show that the AGC can stabilize the BER performance and improve the system performance in the speed of 1m/s.

eess.SP↗

arXiv2020

Wireless Communication Based on Microwave Photon-Level Detection With Superconducting Devices: Achievable Rate Prediction

Future wireless communication system embraces physical-layer signal detection with high sensitivity, especially in the microwave photon level. Currently, the receiver primarily adopts the signal detection based on semi-conductor devices for signal detection, while this paper introduces high-sensitivity photon-level microwave detection based on superconducting structure. We first overview existing works on the photon-level communication in the optical spectrum as well as the microwave photon-level sensing based on superconducting structure in both theoretical and experimental perspectives, including microwave detection circuit model based on Josephson junction, microwave photon counter based on Josephson junction, and two reconstruction approaches under background noise. In addition, we characterize channel modeling based on two different microwave photon detection approaches, including the absorption barrier and the dual-path Handury Brown-Twiss (HBT) experiments, and predict the corresponding achievable rates. According to the performance prediction, it is seen that the microwave photon-level signal detection can increase the receiver sensitivity compared with the state-of-the-art standardized communication system with waveform signal reception, with gain over $10$dB.

eess.SP↗

arXiv2020

A Double-station Access Protocol for Optical Wireless Scattering Communication Networks

We propose a double-station access protocol (DS-CSMA) with multiple backoff mechanism for optical wireless scattering communication networks (OWSCN). %, where two stations can transmit data to single destination simultaneously.can avoid the frames colliding with each other. Furthermore, we extend existing Bianchi Markov model into state transmission model to analyze the collision probability, throughput and average delay. For the application of protocol, we propose to optimize the initial contention window and indicator matrix to maximize throughput. Both numerical and simulation results imply that the proposed protocol can achieve higher throughput and lower transmission delay compared with state-of-art baseline.

cs.NI↗

arXiv2019

On the Sum-Rate Capacity of Poisson Multiple Access Channel with Non-Perfect Photon-Counting Receiver

We first investigate two-user nonasymmetric sum-rate Poisson capacity with non-perfect photoncounting receiver under certain condition and demonstrate three possible transmission strategy, including only one active user and both active users, in sharp contrast to Gaussian multiple access channel (MAC) channel. The two-user capacity reduction due to photon-counting loss is characterized compared with that of continuous Poisson channel. We then study the symmetrical case based on two different methods, demonstrating that the optimal duty cycle for two users must be the same and unique, and the last method maybe can extend to multiple users. Furthermore, we analyze the sum-Rate capacity of Poisson multiple input single output (MISO) MAC. By converting a non-convex optimization problem with a large number of variables into a non-convex optimization problem with two variables, we show that the sum-rate capacity of the Poisson MISO MAC is equivalent to that of SISO under certain condition.

cs.IT↗

arXiv2019

On the Achievable Rate and Capacity for a Sample-based Practical Photon-counting Receiver

We investigate the achievable rate and capacity of a non-perfect photon-counting receiver. For the case of long symbol duration, the achievable rate under on-off keying modulation is investigated based on Kullback-Leibler (KL) divergence and Chernoff $α$-divergence. We prove the tightness of the derived bounds for large peak power with zero background radiation with exponential convergence rate, and for low peak power of order two convergence rate. For large peak power with fixed background radiation and low background radiation with fixed peak power, the proposed bound gap is a small positive value for low background radiation and large peak power, respectively. Moreover, we propose an approximation on the achievable rate in the low background radiation and long symbol duration regime, which is more accurate compared with the derived upper and lower bounds in the medium signal to noise ratio (SNR) regime. For the symbol duration that can be sufficiently small, the capacity and the optimal duty cycle are is investigated. We show that the capacity approaches that of continuous Poisson capacity as $T_s=τ\to0$. The asymptotic capacity is analyzed for low and large peak power. Compared with the continuous Poisson capacity, the capacity of a non-perfect receiver is almost lossless and loss with attenuation for low peak power given zero background radiation and nonzero background radiation, respectively. For large peak power, the capacity with a non-perfect receiver converges, while that of continuous Poisson capacity channel linearly increases. The above theoretical results are extensively validated by numerical results.

cs.IT↗

arXiv2019

Two Dimension Intensity Distribution of Ultraviolet Scattering Communication

Consider a ultraviolet (UV) scattering communication system where the position of the transmitter is fixed and the receiver can move around on the ground. To obtain the link gain effectively and economically, we propose an algorithm based on one-dimensional (1D) numerical integration and an off-line data library. Moreover, we analyze the 2D scattering intensity distributions for both LED and laser, and observe that the contours can be well fitted by elliptic models. The relationships between the characteristics of fitting ellipses and the source parameters are provided by numerical results.

eess.SP↗

arXiv2019

Asynchronous Multiple Access in Optical Wireless Scattering Communication: Achievable Transmission Rates and Receiver Design

We investigate the asynchronous multiple user access communication in optical wireless scattering communication, where different users transmit signals without perfect alignment in the time domain. Firstly, we characterize the received signal based on hidden markov model (HMM) such that the misalignment among different users can be characterized by the state transition. Then, we investigate the achievable rates based on that of the HMM and obtain the approximated solution using Monte Carlo method. We propose the channel estimation based on expectation-maximization (EM) algorithm. Furthermore, we adopt Viterbi and Bahl-Cocke-Jelinek-Raviv (BCJR) algorithms for joint iterative multi-user decoding. Numerical and experimental results illustrate the performance of proposed channel estimation, joint detection and decoding. It is seen from the experimental results that the proposed approaches perform close to the simulation results.

eess.SP↗

arXiv2018

Phototransistor-like Light Controllable IoT Sensor based on Series-connected RGB LEDs

An IoT optical sensor based on the series-connected RGB LEDs is designed, which exhibits the light-controllable optical-to-electrical response like a phototransistor. The IoT sensor has the maximal AC and DC responsivities to the violet light mixed by blue and red light. Its responsivity to the blue light is programmable by the impinging red or green light. A theoretical model based on the light-dependent impedance is developed to interpret its novel optoelectronic response. Such IoT sensor can simultaneously serve as the transmitter and the receiver in the IoT optical communication network, thus significantly reduces the system complexity.

physics.app-ph↗