Searcharxiv⌕ Search
Home/Archive/arXiv

arXiv · 1508.04739

Fabrication of a simple apparatus for the Seebeck coefficient measurement in high temperature region

Saurabh Singh·Sudhir K. Pandey
View original source ↗Read source document ↗Export metadata ↓

Abstract

A simple apparatus for the measurement of Seebeck coefficient ($\alpha$) in the temperature range 300-620 K has been fabricated. Our design is appropriate for the characterization of samples with different geometries like disk and rod shaped. The sample holder assembly of the apparatus has been designed in such a way that, single heater used for sample heating purpose is enough to provide a self maintain temperature gradient (1-10 K) across the sample. The value of $\alpha$ is obtained without explicit measurement of temperature gradient. The whole apparatus is fabricated from the materials, which are commonly available, so that any part can be replaced in case of any damage. Commercially available standard Nickel (Ni) metal sample has been used as a reference material for calibration of the instrument. The experimentally observed value of $\alpha$ by our apparatus gives the similar temperature dependent behavior as reported in the literature. In order to study the thermoelectric behavior of oxide materials, we have synthesized polycrystalline LaCoO$_{3}$ powder samples by using solution combustion method and investigated the thermoelectric properties. Temperature dependent thermoelectric behavior of these samples were characterized in the temperature range 300-600 K.

Explore related subjects

physics.ins-detcond-mat.mtrl-sci

Keep this discovery

BibTeXRIS

Saurabh Singh, Sudhir K. Pandey. 2015-08-19. Fabrication of a simple apparatus for the Seebeck coefficient measurement in high temperature region. https://doi.org/10.1016/j.measurement.2017.01.049

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related papers

arXiv2026

High-Speed Semi-FE Readout Module for ATLAS MDT at HL-LHC: Design and Production-Level Characterization

The High-Luminosity upgrade of the Large Hadron Collider (HL-LHC) introduces increased demands on the ATLAS Muon Spectrometer, particularly in terms of data throughput, timing distribution and system reliability. The Phase-II Chamber Service Module (CSM) is a key component of the upgraded Monitored Drift Tube (MDT) trigger and readout system, providing a high-speed interface between the front-end electronics and the backend systems. This paper describes the design and implementation of the Phase-II CSM, together with its validation. The results show that the CSM supports two independent optical uplinks, each operating at a line rate of 10.24 Gbps, together with clock distribution and slow control in the expected operating environment. Integration with small-diameter MDT (sMDT) chambers and tests with the prototype L0MDT trigger system are also presented. The CSM boards are now in production and will be used for installation and integration during the upcoming LHC Long Shutdown.

physics.ins-det↗
arXiv2026

Spectral Discrimination of Deposited Gamma-Ray Energies in a Simulated CeBr$_3$ Scintillator

We show that wavelength measurements of individual detected optical photons may provide additional information about gamma-ray energy deposited in a CeBr$_3$ crystal when the detected-photon-count distributions overlap for nearby gamma-ray energies. Monoenergetic 662 and 629 keV gammas are used in a Geant4 simulation of a $25\times25\times20~\mathrm{mm^3}$ CeBr$_3$ crystal. Assuming a light yield of $6.0\times10^4$ photons/MeV, a wavelength-independent photon-detection efficiency of 30%, and a wavelength resolution of $\sigma_{\lambda}=40$ nm, we find that the fraction of photons reconstructed above 385 nm gives an event-level separation of $\sim$ 2 standard deviations between the 662 and 629 keV event populations selected within the same $\sim$ 1%-wide detected-photon-count interval. No timing or reconstructed interaction-position information is used. The result demonstrates, within the present simulation model, that event-dependent optical spectra can retain energy information beyond an undifferentiated photon count.

physics.ins-det↗
arXiv2026

Operation of a negative ion gas time projection chamber without electronegative fill gases

The high fidelity reconstruction of particle tracks in micropatterned gaseous time projection chambers renders this technology ideal for future rare-event searches, including direction-sensitive dark matter experiments. Large drift distances are typically required for such experiments, so that the overall spatial resolution is limited by diffusion. Negative ion drift exhibits lower diffusion than electron drift and is thus an attractive option for realising a large-scale detector. The use of electronegative gases to create negative ions introduces technical challenges, most notably a reduction in gain when compared to conventional gas mixtures. In this study, we demonstrate a new method for negative ion generation via dissociative electron attachment using the conventional molecular fill gas CF$_4$. Our optical measurements of negative ion drift indicate electron attachment lengths of $<$1 mm and comparable gain to electron avalanches. The individual negative ion avalanches were also time-resolved, allowing the number of ions reaching the readout to be counted. We measure an improved energy resolution by single ion counting, relative to an integrated electron avalanche signal measured under identical gain conditions.

physics.ins-det↗