arXiv subjects

A. Boikov

Publications and source records attributed to A. Boikov.

5 recordsLinked to original sources

arXiv2025

Beam-test evaluation of pre-production Low Gain Avalanche Detectors for the ATLAS High Granularity Timing Detector

The High Granularity Timing Detector (HGTD) will be installed in the ATLAS experiment as part of the Phase-II upgrade for the High Luminosity-Large Hadron Collider (HL-LHC). It will mitigate pile-up effects in the forward region, and measure per bunch luminosity. The design of HGTD is based on Low Gain Avalanche Detector (LGAD) sensors. This paper presents the results of beam-test campaigns conducted at CERN and DESY in 2023 and 2024 on single LGADs from HGTD pre-production test structures, before and after neutron irradiation up to fluences of $2.5 \times 10^{15}~\mathrm{n_{eq}/cm^2}$. The tested LGADs can meet HGTD requirements in terms of charge collection, time resolution, and hit efficiency, even under HL-LHC end-of-life conditions, supporting their deployment in the final detector.

physics.ins-det↗

arXiv2025

Thermal Cycling Reliability of Hybrid Pixel Sensor Modules for The ATLAS High Granularity Timing Detector

The reliability of bump connection structures has become a critical aspect of future silicon detectors for particle physics. The High Granularity Timing Detector (HGTD) for the ATLAS experiment at the High-Luminosity Large Hadron Collider will require 8032 hybrid pixel sensor modules, composed of two Low Gain Avalanche Diode sensors bump-bonded to two readout ASICs and glued to a passive PCB. The detector will operate at low temperature (-30 degrees Celsius) to mitigate the impact of irradiation. The thermomechanical reliability of flip-chip bump connections in HGTD modules is a critical concern, particularly due to their characteristically lower bump density (pixel pitch dimensions of 1.3 mm by 1.3 mm). This paper elaborates on the challenges arising from this design characteristic. Finite element analysis and experimental testing were employed to investigate failure modes in the flip-chip bump structures under thermal cycling from -45 degrees Celsius to 40 degrees Celsius and to guide the module redesign. The optimized design demonstrates significantly enhanced robustness and is projected to fulfill the full lifetime requirements of the HGTD.

physics.ins-det↗

arXiv2025

The design of the data acquisition system for SPD experiment

The Spin Physics Detector (SPD) experiment at the NICA collider in JINR aims to investigate the spin structure of nucleons and spin-related phenomena. The combination of the number of background processes, the event rate and conditions for event selection makes the use of a classical trigger system impractical, requiring a triggerless data acquisition (DAQ) system. The DAQ system is designed to ensure precise time synchronization, efficient data collection, and high-throughput processing. Its architecture combines commercially available FPGA-based modules and high-speed optical interfaces with custom-developed components based on widely accessible technologies. This approach provides scalability from 180,000 at the initial stage of the experiment to more than 600,000 detector channels in the final configuration and supports data rates up to 20 GB/s or more. The modular system design ensures adaptability for future upgrades while maintaining high efficiency and reliability. Such an approach makes the DAQ system suitable for other high-rate nuclear physics experiments.

physics.ins-det↗

arXiv2024

Technical Design Report of the Spin Physics Detector at NICA

The Spin Physics Detector collaboration proposes to install a universal detector in the second interaction point of the NICA collider under construction (JINR, Dubna) to study the spin structure of the proton and deuteron and other spin-related phenomena using a unique possibility to operate with polarized proton and deuteron beams at a collision energy up to 27 GeV and a luminosity up to $10^{32}$ cm$^{-2}$ s$^{-1}$. As the main goal, the experiment aims to provide access to the gluon TMD PDFs in the proton and deuteron, as well as the gluon transversity distribution and tensor PDFs in the deuteron, via the measurement of specific single and double spin asymmetries using different complementary probes such as charmonia, open charm, and prompt photon production processes. Other polarized and unpolarized physics is possible, especially at the first stage of NICA operation with reduced luminosity and collision energy of the proton and ion beams. This document is dedicated exclusively to technical issues of the SPD setup construction.

hep-ex↗

arXiv2023

High efficiency muon registration system based on scintillator strips

Experiments such as mu2e (FNAL, USA) and COMET (KEK, Japan), seeking the direct muon-to-electron conversion as part of the study of Charged Leptons Flavor Violation processes, should have a extremely high, up-to 99.99\%, efficiency muon detection system with a view to their subsequent suppression as background. In this article, the possibility to achieve such efficiency for a short and long term is discussed for modules based on 7- or 10-mm-thick but same 40-mm-wide plastic scintillation strips with single 1.2 mm WLS fiber glued into the groove along the strip and using MPPC/SiPM for light detection. A Simplified Light Yield Distribution method to estimate the efficiency of the module was proposed and the simulation results obtained with GEANT 4 for a system based on a 4-by-4 array of 7x40x3000 mm strips compared with the experimental data. Found that for the systems required the high level registration efficiency at the 99.99\% and more, it is important to improve the light yield as much as possible and achieve the gap between neighbor scintillation volumes as small as possible.

physics.ins-det↗