Searcharxiv⌕ Search

arXiv subjects

A. N. Ramaprakash

Publications and source records attributed to A. N. Ramaprakash.

At least 19 recordsLinked to original sources

Multi-Wavelength Diagnostics of Pre-Flare Evolution with Aditya-L1: From the Solar Chromosphere to the Corona

The pre-flare phase of solar flares provides important insight into the processes that drive active regions toward instability. We investigate chromospheric pre-flare activity using observations from the Solar Ultraviolet Imaging Telescope (SUIT) onboard Aditya-L1, complemented with X-ray measurements from High Energy L1 Orbiting X-ray Spectrometer (HEL1OS) and Solar Low Energy X-ray Spectrometer (SoLEXS). We analyse seven M- and X-class flares, focusing on spatially resolved Mg II h (2803~Å) observations from SUIT. We identify 102 pre-flare transients within regions of interest prior to flare onset. These transients are detected in the Mg II h channel, with no counterparts in continuum filters, confirming their chromospheric origin. In most cases, the transients are co-spatial with polarity inversion lines (PILs) and the eventual flaring region. Approximately 28~\% of transients have X-ray counterparts in HEL1OS (10-30~keV); The Spectrometer Telescope for Imaging X-rays (STIX) spectral analysis reveals non-thermal emission in a subset, indicating that some transients are small-scale flare-like events. A hot X-ray onset is identified in four cases. For the remaining three cases, the signal-to-noise ratio above the background is insufficient to determine whether a hot-onset phase is present. The peak-flux distribution of the transients follows a broken power law with indices $α_1 = 1.64^{+0.59}_{-0.57}$ and $α_2 = 3.12^{+0.64}_{-0.61}$, with the higher-energy slope consistent with the Ly-$α$ flare distribution. These results suggest that chromospheric pre-flare transients represent small-scale magnetic energy-release events that contribute to the progressive destabilisation of active regions prior to major flare onset.

astro-ph.SR↗

WALOP-South: a four camera one shot imaging polarimeter for the PASIPHAE survey. Paper III -- PSF modelling

The two WALOP instruments, built for the PASIPHAE survey, will measure the linear polarization of large numbers of stars in the Galactic polar regions in the SDSS-$r$ band. They are designed with a wide field-of-view, enabling measurement of the Stokes parameters $I$, $q$, and $u$ for multiple stars simultaneously within a $35^\prime \times 35^\prime$ region of sky for WALOP-South and $30^\prime \times 30^\prime$ region for WALOP-North. In this paper, we present a polar shapelet-based PSF photometry framework for well-sampled stellar point sources applicable to WALOP-type wide-field polarimeters. Polar shapelets are a set of orthogonal basis functions, constructed from Gauss-Hermite or Gauss-Laguerre polynomials, that are well-suited to modelling localized PSF in a compact and efficient way. We developed an efficient PSF modelling method that uses polar shapelets as basis functions to reconstruct the spatial variation of the PSF shape across the CCD using Zemax-simulated images of one of the WALOP instruments, and show that a limited number of shapelet coefficients are sufficient to capture this variation consistently across different CCD locations. To simulate realistic star images, we introduce random sub-pixel shifts in the star centroids in the Zemax-simulated images, and account for this using a two-step iterative method that alternately estimates the PSF model and the sub-pixel centroid shift. Applying PSF photometry to the target faint stars, we demonstrate that the photometric accuracy of approximately 0.15% is achievable, and that the reconstructed PSF model can be incorporated into the photometry across different seeing conditions, meeting the polarimetric science requirements of the PASIPHAE survey.

astro-ph.IM↗

Unraveling the Secrets of the lower Solar Atmosphere: One year of Operation of the Solar Ultraviolet Imaging Telescope (SUIT) on board Aditya-L1

The Solar Ultraviolet Imaging Telescope (SUIT) is an instrument onboard Aditya--L1, the first solar space observatory of the Indian Space Research Organization (ISRO), India, launched on September 2, 2023. SUIT is designed to image the Sun in the 200--400 nm wavelength band in eight narrowband and three broadband filters. SUIT's science goals start with observing the solar atmosphere and large-scale continuum variations, the physics of solar flares in the NUV region, and many more. The paper elucidates the functioning of the instrument, software packages developed for easier calibration, analysis, and feedback, calibration routines, and the regular maintenance activity of SUIT during the first year of its operation. The paper also presents the various operations undergone by, numerous program sequences orchestrated to achieve the science requirements, and highlights some remarkable observations made during the first year of observations with SUIT.

astro-ph.SR↗

Evidence for cloud-to-cloud variations in the ratio of polarized thermal dust emission to starlight polarization

The correlation between optical starlight polarization and polarized thermal dust emission can be used to infer intrinsic dust properties. This correlation is quantified by the ratio Rp/p, which has been measured to be 5.42 +/- 0.05 MJy sr^-1 at 353 GHz when averaged over large areas of the sky. We investigate this correlation using newly published stellar polarimetric data densely sampling a continuous sky region of ~4 square degrees at intermediate Galactic latitude. We combine RoboPol optical polarization measurements for 1,430 stars with submillimeter data from the Planck satellite at 353 GHz. We perform linear fits between the Planck (Qs, Us) and optical (qv, uv) Stokes parameters, accounting for the differences in resolution between the two datasets as well as the distribution of clouds along the line of sight. We find that in this region of the sky the Rp/p value is 3.67 +/- 0.05 MJy sr^-1, indicating a significantly shallower slope than that found previously using different stellar samples. We also find significant differences in the fitted slopes when fitting the Qs-qv and Us-uv data separately. We explore two explanations using mock data: miscalibration of polarization angle and variations in Rp/p along the line of sight due to multiple clouds. We show that the former can produce differences in the correlations of Qs-qv and Us-uv, but large miscalibration angles would be needed to reproduce the magnitude of the observed differences. Our simulations favor the interpretation that Rp/p differs between the two dominant clouds that overlap on the sky in this region. The difference in Rp/p suggests that the two clouds may have distinct dust polarimetric properties. With knowledge from the tomographic decomposition of the stellar polarization, we find that one cloud appears to dominate the correlation of Us-uv, while both clouds contribute to the correlation of the Qs-qv data.

astro-ph.GA↗

Wide Area Linear Optical Polarimeter Control Software

The WALOPControl software is designed to facilitate comprehensive control and operation of the WALOP (Wide Area Linear Optical Polarimeter) polarimeters, ensuring safe and concurrent management of various instrument components and functionalities. This software encompasses several critical requirements, including control of the filter wheel, calibration half-wave plate, calibration polarizer, guider positioning, focusers, and 4 concurrent CCD cameras. It also manages the host telescope and dome operations while logging operational parameters, user commands, and environmental conditions for troubleshooting and stability. It provides a user-friendly graphical user interface, secure access control, a notification system for errors, and a modular configuration for troubleshooting are integral to the software's architecture. It is accessible over the internet with the backend developed using NodeJS and ExpressJS, featuring a RESTful API that interacts with a MongoDB database, facilitating real-time status updates and data logging. The frontend utilizes the React.JS framework, with Redux for state management and Material UI for the graphical components. The system also allows for automatic observations based on user-defined schedules. A Continuous Integration and Continuous Deployment (CI CD) pipeline ensures the software's reliability through automated testing and streamlined deployment. The WALOPControl software is a key component of the PASIPHAE (Polar-Areas Stellar Imaging in Polarimetry High Accuracy Experiment) project, which aims to study the dust and magnetic field of the Milky Way by observing the polarization of starlight.

astro-ph.IM↗

X-class flare on Dec 31, 2023, observed by the Solar Ultraviolet Imaging Telescope on board Aditya-L1

We present the multi-wavelength study of the ejection of a plasma blob from the limb flare SOL2023-12-31T21:36:00 from NOAA 13536 observed by the Solar Ultraviolet Imaging Telescope (SUIT) on board Aditya-L1. We use SUIT observations along with those from Atmospheric Imaging Assembly (AIA) on board SDO and Spectrometer/Telescope for Imaging X-rays (STIX) on board Solar Orbiter to infer the kinematics and thermal nature of the ejected blob and its connection to the associated flare. The observations show that the flare was comprised of two eruptions. The blob was ejected during the first eruption and later accelerated to velocities over 1500 km/s measured at a maximum projected height of ~ 178 Mm from the Sun's surface. The acceleration of the ejected plasma blob is co-temporal with the bursty appearance of the hard X-ray light curve recorded by STIX. Radio spectrogram observations from STEREO-A/WAVES and RSTN reveal type III bursts at the same time, indicative of magnetic reconnection. DEM analysis using AIA observations suggests the plasma blob is comprised of cooler and denser plasma in comparison to the ambient corona. To the best of our knowledge, this is the first observation of such a plasma blob in the NUV, providing crucial measurements for eruption thermodynamics.

astro-ph.SR↗

Test and Calibration of the Solar Ultraviolet Imaging Telescope (SUIT) on board Aditya-L1

The Solar Ultraviolet Imaging Telescope (SUIT) on board the AdityaL1 mission observes the Sun in the 200-400 nm wavelength range. This paper presents the results of various on ground and on board tests and their comparison with the specifications. Moreover, we also present the scheme for data calibration. We demonstrate that the test results are compliant with the specified figures, except the spatial resolution. Such discrepancy will limit the photometric measurements only, at a scale of 2.2" instead of 1.4" as originally envisioned. The results obtained here show that SUIT observations open up a new window for solar observations.

astro-ph.IM↗

Near and Mid UltraViolet Observations of X-6.3 flare on 22nd February 2024 recorded by the Solar Ultraviolet Imaging Telescope on board Aditya-L1

Solar flares are regularly observed in extreme ultraviolet (EUV), soft X-rays (SXR), and hard X-rays (HXR). However, those in near and mid-UV are sparse. The Solar Ultraviolet Imaging Telescope (SUIT) onboard the Aditya-L1, launched on 2nd September, 2023 provides regular observations in the 200-400 nm wavelength range through eleven filters. Here, we report the observation of the X6.3 flare on Feb 22, 2024 using eight narrow band (NB) filters of SUIT. We have also used co-spatiotemporal observations from SDO/AIA, Solar Orbiter/STIX, GONG H$α$, Aditya-L1/SoLEXS and GOES. We obtained light curves over the flaring region from AIA 1600, 1700 Å and GONG H$α$ and compared them with the disk-integrated lightcurve obtained from GOES and SoLEXS SXR and STIX HXR. We find that the flare peaks in SUIT NB01, NB03, NB04, and NB08 filters simultaneously with HXR, 1600, and 1700 Å along with the peak temperature obtained from SoLEXS. In contrast, in NB02 and NB05, the flare peaks $\sim$ 2 minutes later than the HXR peak, while in NB06 and NB07, the flare peaks $\sim$ 3 minutes after the GOES soft X-ray peak. To the best of our knowledge, this is the first observation of a flare in these wavelengths (except in NB03, NB04 and NB05). Moreover, for the first time, we show the presence of a bright kernel in NB02. These results demonstrate the capabilities of SUIT observations in flare studies.

astro-ph.SR↗

The Solar Ultraviolet Imaging Telescope on board Aditya-L1

The Solar Ultraviolet Imaging Telescope (SUIT) is an instrument on the Aditya-L1 mission of the Indian Space Research Organization (ISRO) launched on September 02, 2023. SUIT continuously provides, near-simultaneous full-disk and region-of-interest images of the Sun, slicing through the photosphere and chromosphere and covering a field of view up to 1.5 solar radii. For this purpose, SUIT uses 11 filters tuned at different wavelengths in the 200{--}400~nm range, including the Mg~{\sc ii} h~and~k and Ca~{\sc ii}~H spectral lines. The observations made by SUIT help us understand the magnetic coupling of the lower and middle solar atmosphere. In addition, for the first time, it allows the measurements of spatially resolved solar broad-band radiation in the near and mid ultraviolet, which will help constrain the variability of the solar ultraviolet irradiance in a wavelength range that is central for the chemistry of the Earth's atmosphere. This paper discusses the details of the instrument and data products.

astro-ph.SR↗

Science Filter Characterization of the Solar Ultraviolet Imaging Telescope (SUIT) on board Aditya-L1

The Solar Ultraviolet Imaging Telescope (SUIT) on board the Aditya-L1 mission is designed to observe the Sun across 200-400 nm wavelength. The telescope used 16 dichroic filters tuned at specific wavelengths in various combinations to achieve its science goals. For accurate measurements and interpretation, it is important to characterize these filters for spectral variations as a function of spatial location and tilt angle. Moreover, we also measured out-of-band and in-band transmission characteristics with respect to the inband transmissions. In this paper, we present the experimental setup, test methodology, and the analyzed results. Our findings reveal that the transmission properties of all filters meet the expected performance for spatial variation of transmission and the transmission band at a specific tilt angle. The out-of-band transmission for all filters is below 1% with respect to in-band, except for filters BB01 and NB01. These results confirm the capabilities of SUIT to effectively capture critical solar features in the anticipated layer of the solar atmosphere.

astro-ph.SR↗

The WALOP-North Instrument I: Optical Design, Filter Design, Calibration

The Wide Area Linear Optical Polarimeter North (WALOP-North) is an optical polarimeter designed for the needs of the PASIPHAE survey. It will be installed on the 1.3m telescope at the Skinakas Observatory in Crete, Greece. After commissioning, it will measure the polarization of millions of stars at high Galactic latitude, aiming to measure hundreds of stars per $deg^2$. The astronomical filter used in the instrument is a modified, polarimetrically-neutral broadband SDSS-r. This instrument will be pioneering one due to its large field-of-view (FoV) of $30\times 30$ $arcmin^2$ and high accuracy polarimetry measurements. The accuracy and sensitivity of the instrument in polarization fraction will be at the 0.1\% and 0.05\% level, respectively. Four separate 4k$\times$4k CCDs will be used as the instrument detectors, each imaging one of the $0°, 45°, 90°$ and $135°$ polarized FoV separately, therefore making the instrument a four-channel, one-shot polarimeter. Here, we present the overall optical design of the instrument, emphasizing on the aspects of the instrument that are different from WALOP-South. We also present a novel design of filters appropriate for polarimetry along with details on the management of the instrument size and its polarimetric calibration.

astro-ph.IM↗

A Partial Near-infrared Guide Star Catalog for Thirty Meter Telescope Operations

At first light, the Thirty Meter Telescope (TMT) near-infrared (NIR) instruments will be fed by a multiconjugate adaptive optics instrument known as the Narrow Field Infrared Adaptive Optics System (NFIRAOS). NFIRAOS will use six laser guide stars to sense atmospheric turbulence in a volume corresponding to a field of view of 2', but natural guide stars (NGSs) will be required to sense tip/tilt and focus. To achieve high sky coverage (50% at the north Galactic pole), the NFIRAOS client instruments use NIR on-instrument wavefront sensors that take advantage of the sharpening of the stars by NFIRAOS. A catalog of guide stars with NIR magnitudes as faint as 22 mag in the J band (Vega system), covering the TMT-observable sky, will be a critical resource for the efficient operation of NFIRAOS, and no such catalog currently exists. Hence, it is essential to develop such a catalog by computing the expected NIR magnitudes of stellar sources identified in deep optical sky surveys using their optical magnitudes. This paper discusses the generation of a partial NIR Guide Star Catalog (IRGSC), similar to the final IRGSC for TMT operations. The partial catalog is generated by applying stellar atmospheric models to the optical data of stellar sources from the Panoramic Survey Telescope and Rapid Response System (Pan-STARRS) optical data and then computing their expected NIR magnitudes. We validated the computed NIR magnitudes of the sources in some fields by using the available NIR data for those fields. We identified the remaining challenges of this approach. We outlined the path for producing the final IRGSC using the Pan-STARRS data. We have named the Python code to generate the IRGSC as irgsctool, which generates a list of NGS for a field using optical data from the Pan-STARRS 3pi survey and also a list of NGSs having observed NIR data from the UKIRT Infrared Deep Sky Survey if they are available.

astro-ph.IM↗

Improving polarimetric accuracy of RoboPol to $<$ 0.05 % using a half-wave plate calibrator system

RoboPol is a four-channel, one-shot linear optical polarimeter that has been successfully operating since 2013 on the 1.3 m telescope at Skinakas Observatory in Crete, Greece. Using its unique optical system, it measures the linear Stokes parameters $q$ and $u$ in a single exposure with high polarimetric accuracy of 0.1% - 0.15% and 1 degree in polarization angle in the R broadband filter. Its performance marginally degrades in other broadband filters. The source of the current instrumental performance limit has been identified as unaccounted and variable instrumental polarization, most likely originating from factors such as temperature and gravity-induced instrument flexure. To improve the performance of RoboPol in all broadband filters, including R, we have developed a rotating half-wave plate calibrator system. This calibrator system is placed at the beginning of the instrument and enables modulation of polarimetric measurements by beam swapping between all four channels of RoboPol. Using the new calibrator system, we observed multiple polarimetric standard stars over two annual observing seasons with RoboPol. This has enabled us to achieve a polarimetric accuracy of better than 0.05 % in both $q$ and $u$, and 0.5 degrees in polarization angle across all filters, enhancing the instrument's performance by a factor of two to three.

astro-ph.IM↗

Systems design, assembly, integration and lab testing of WALOP-South Polarimeter

Wide-Area Linear Optical Polarimeter (WALOP)-South is the first wide-field and survey-capacity polarimeter in the optical wavelengths. On schedule for commissioning in 2024, it will be mounted on the 1 m SAAO telescope in Sutherland Observatory, South Africa to undertake the PASIPHAE sky survey. PASIPHAE program will create the first polarimetric sky map in the optical wavelengths, spanning more than 2000 square degrees of the southern Galactic region. The innovative design of WALOP-South will enable it to measure the linear polarization (Stokes parameters $q$ and $u$), in a single exposure, of all sources in a field of view (FoV) of $35\times35$ arcminutes-squared in the SDSS-r broadband and narrowband filters between 500-750 nm with 0.1 % polarization accuracy. The unique goals of the instrument place very stringent systems engineering goals, including on the performance of the optical, polarimetric, optomechanical, and electronic subsystems. All the subsystems have been designed carefully to meet the overall instrument performance goals. As of May 2024, all the instrument optical and mechanical subsystems have been assembled and are currently getting tested and integrated. The complete testing and characterization of the instrument in the lab is expected to be completed by August 2024. In this paper, we will present (a) the design and development of the entire instrument and its major subsystems, focusing on the opto-mechanical design which has not been reported before, and (b) assembly and integration of the instrument in the lab and early results from lab characterization of the instrument.

astro-ph.IM↗

Spectropolarimeter on a 2--4 m class telescope and proposed science cases

We propose a spectropolarimeter a covering wavelength range of 3200--7000 Å [3200Å chosen as lower limit to go to the atmospheric cut-off. It's ``needed" for some Serkowski curves and would make the instrument even more unique] for a 2-4~m class telescope. In this article, we discuss the science cases which will be covered with this proposed instrument. The technical requirements and analysis plan for each science case is also discussed. This spectropolarimeter targeting exciting galactic and extra-galactic research, will be unique instrument on a 2-4~m facilities.

astro-ph.GA↗

The first degree-scale starlight-polarization-based tomography map of the magnetized interstellar medium

We present the first degree-scale tomography map of the dusty magnetized interstellar medium (ISM) from stellar polarimetry and distance measurements. We used the RoboPol polarimeter at Skinakas Observatory to conduct a survey of starlight polarization in a region of the sky of 4 square degrees. We propose a Bayesian method to decompose the stellar-polarization source field along the distance to invert the 3D volume occupied by the observed stars. We used it to obtain the first 3D map of the dusty magnetized ISM. Specifically, we produced a tomography map of the orientation of the plane-of-sky (POS) component of the magnetic field threading the diffuse, dusty regions responsible for the stellar polarization. For the targeted region centered on Galactic coordinates $(l,b) \approx (103.3^\circ, 22.3^\circ)$, we identified several ISM clouds. Most of the lines of sight intersect more than one cloud. A very nearby component was detected in the foreground of a dominant component from which most of the polarization signal comes. Farther clouds, with a distance of up to 2~kpc, were similarly detected. Some of them likely correspond to intermediate-velocity clouds seen in HI spectra in this region of the sky. We found that the orientation of the POS component of the magnetic field changes along distance for most of the lines of sight. Our study demonstrates that starlight polarization data coupled to distance measures have the power to reveal the great complexity of the dusty magnetized ISM in 3D and, in particular, to provide local measurements of the POS component of the magnetic field. This demonstrates that the inversion of large data volumes, as expected from the PASIPHAE survey, will provide the necessary means to move forward in the modeling of the Galactic magnetic field and of the dusty magnetized ISM as a contaminant in observations of the cosmic microwave background polarization.

astro-ph.GA↗

Large Projects in Astronomy: An Indian Endeavour

Policy Brief on "Large Projects in Astronomy: An Indian Endeavour", distilled from the corresponding panel that was part of the discussions during S20 Policy Webinar on Astroinformatics for Sustainable Development held on 6-7 July 2023. Cutting-edge astronomy initiatives often entail substantial investment and require a high level of expertise. Even the most technologically advanced nations recognize the value of establishing international partnerships to secure both financial resources and talent for these ambitious endeavours as they hold immense promise for catalysing transformative scientific discoveries, driving technological innovation, provide training opportunities for the next generation of scientists and engineers, and expanding our understanding of the cosmos that surrounds us. Crucially, large-scale multilateral collaborations serve as powerful agents for promoting unity and peace among the global population. Participants from various nations share a vested interest in the success of these projects and the wealth of knowledge they yield, fostering a sense of common purpose and shared goals. By utilizing astroinformatics capabilities, these initiatives are not merely enhancing our comprehension of the universe but are also actively contributing to the attainment of sustainable development objectives. In this discussion, we delve into the challenges faced, and prospects for substantial astronomical undertakings. Additionally, we present recommendations aimed at guaranteeing their effectiveness and optimizing their influence on both scientific advancement and society. The policy webinar took place during the G20 presidency in India (2023). A summary based on the seven panels can be found here: arxiv:2401.04623.

astro-ph.IM↗

AstroInformatics: Recommendations for Global Cooperation

Policy Brief on "AstroInformatics, Recommendations for Global Collaboration", distilled from panel discussions during S20 Policy Webinar on Astroinformatics for Sustainable Development held on 6-7 July 2023. The deliberations encompassed a wide array of topics, including broad astroinformatics, sky surveys, large-scale international initiatives, global data repositories, space-related data, regional and international collaborative efforts, as well as workforce development within the field. These discussions comprehensively addressed the current status, notable achievements, and the manifold challenges that the field of astroinformatics currently confronts. The G20 nations present a unique opportunity due to their abundant human and technological capabilities, coupled with their widespread geographical representation. Leveraging these strengths, significant strides can be made in various domains. These include, but are not limited to, the advancement of STEM education and workforce development, the promotion of equitable resource utilization, and contributions to fields such as Earth Science and Climate Science. We present a concise overview, followed by specific recommendations that pertain to both ground-based and space data initiatives. Our team remains readily available to furnish further elaboration on any of these proposals as required. Furthermore, we anticipate further engagement during the upcoming G20 presidencies in Brazil (2024) and South Africa (2025) to ensure the continued discussion and realization of these objectives. The policy webinar took place during the G20 presidency in India (2023). Notes based on the seven panels will be separately published.

astro-ph.IM↗