arXiv subjects

Abderrahime Sekkat

Publications and source records attributed to Abderrahime Sekkat.

3 recordsLinked to original sources

arXiv2026

Rapid Atmospheric Vapor Deposition of H:In2O3 Transparent Conducting Oxide Thin Films

Transparent conducting oxides (TCOs) are essential for the optoelectronics industry, but there is a critical gap in cost-effective methods to rapidly deposit low sheet resistance, high transmittance films without damaging delicate materials, including emerging soft semiconductors like metal-halide perovskites. In this work, atmospheric pressure chemical vapor deposition (AP-CVD) is used to synthesise H:In2O3 films with 7.20+/-0.01 Ohm/sq sheet resistance (0.50+/-0.06 mOhm.cm resistivity) and transmittance up to 89% in the near-infrared (NIR), surpassing commercial sputter-deposited indium tin oxide. The growth rate is 40x higher than atomic layer deposition (ALD), and the AP-CVD films are fully processed under atmospheric conditions at only 140 C. Comparison of secondary ion mass spectrometry and time-of-flight elastic recoil detection analysis with changes in carrier concentration indicate that H dopants are introduced from the water oxidant. There is an increase in mobility form 40+/-10 cm2/Vs to 160+/-30 cm2/Vs when changing from O2 to H2O as the oxidant, which is attributed to H dopants passivating oxygen vacancies that act as carrier scattering centers. This work establishes AP-CVD as a promising method for manufacturing high figure-of-merit TCOs in a rapid, scalable and cost-effective manner, using mild growth conditions compatible with thermally-sensitive materials.

cond-mat.mtrl-sci↗

arXiv2026

Circularity in Perovskite-Based Tandem Photovoltaics for Terawatt-Scale Deployment

As photovoltaics (PVs) scale from one to multiple terawatts over the next decade, ensuring sustainable deployment is urgently required. Crystalline silicon (c-Si) PVs, the current industry standard, will generate an estimated 160 million tonnes of waste by 2050, and there remains complex technoeconomic challenges associated with their recycling. Metal-halide perovskite (MHP)-based tandem PVs not only promise higher power conversion efficiencies than single-junction c-Si devices, but also offer intrinsic advantages for circularity, including simpler device architectures, low-temperature processing, and more accessible materials recovery routes. At this pivotal juncture when perovskite PVs begin to enter the market, this review examines the critical circularity challenges that must be addressed: substitution of scarce raw materials, scalable recycling protocols, cost-effective stack delamination, safe lead sequestration, and policy frameworks to encourage circularity across the device lifecycle with effective incentives. By integrating the materials, technoeconomic and policy dimensions that go beyond conventional lifecycle assessments, we outline actionable strategies to co-optimize device performance and sustainability. This review aims to guide researchers, policymakers, and industry stakeholders in steering perovskite-based tandem PVs towards a circular and responsible commercialization pathway within the global clean-energy transition.

cond-mat.mtrl-sci↗

arXiv2020

Facile patterning of functional materials via gas-phase 3D printing

Spatial Atomic Layer Deposition (SALD) is a recent approach that is up to two orders of magnitude faster than conventional ALD, and that can be performed at atmospheric pressure and even in the open air. Previous works have exploited these assets to focus on the possibility of high-rate, large-area deposition for scaling up into mass production. Conversely, here we show that SALD indeed represents an ideal platform for the selective deposition of functional materials by proper design and miniaturization of SALD close-proximity heads. In particular, we have used the potential offered by 3D printing to fabricate custom close-proximity SALD injection heads. By using 3D printing, the heads can be easily designed and readily modified to obtain different deposition areas, free-form patterns, and even complex multimaterial structures. The heads can be printed in different materials to adjust to the chemistry of the precursors and the deposition conditions used. Polymeric heads can be used as cheap (even disposable) heads that are both used for performing deposition and for prototyping and optimization purposes. Finally, by designing a miniaturized head with circular concentric gas channels, 3D printing of functional materials can be performed with nanometric resolution in Z. This constitutes a new 3D printing approach based on gaseous precursors. Because the selective deposition strategies presented here are based on the SALD process, conformal and continuous thin films of functional materials can be printed at low temperatures and with high deposition rate in the open air. Our approach represents a new versatile way of printing functional materials and devices with spatial and topological control, thus extending the potential of SALD and ALD in general, and opening a new avenue in the field of area-selective deposition of functional materials.

cond-mat.mtrl-sci↗