arXiv subjects

Alice Ponti

Publications and source records attributed to Alice Ponti.

10 recordsLinked to original sources

arXiv2026

In orbit background for hard X-ray CubeSat polarimeters: case study of the CUSP mission in low-earth orbit

The CUbesat Solar Polarimeter (CUSP) project aims to measure the linear polarization of solar flares in the 25 - 100 keV hard X-ray band using a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop innovative CubeSat technologies and missions. As part of CUSPs Phase B study, initiated in December 2024 and closed on July 2nd, 2026, estimating the in orbit background to optimize the signal-to-background ratio was one of the key objectives. In low-Earth orbit, the instrument is exposed to cosmic and albedo X-ray backgrounds, charged particles, and secondary radiation from the spacecraft and atmosphere. Simulating these contributions enables optimization of detector geometry and shielding to maximize signal-to-noise performance. We present initial in orbit background estimates for CUSP using a Geant4-based simulator. A detailed mass model of the CUSP has been implemented to simulate background components and estimate the background count rate in the CUSP orbit.

astro-ph.IM↗

arXiv2026

The CUSP CubeSat mission for space weather multi-physics analysis, design, and testing

The CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. We present the outcomes of the CUSP's Phase B study, which is ended on 2 July 2026. The design solutions adopted for the mission's most critical multi-physics design drivers will be discussed, these solutions have been formulated and applied to demonstrate compliance with system requirements at both the spacecraft and platform levels. Moreover, we will discuss the validation of the Payload model based on the environmental testing campaign (e.g., vibration) carried out on a demonstrator.

astro-ph.IM↗

arXiv2026

Compton Polarimeter Prototype for the CUbesat Solar Polarimeter (CUSP) mission

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band (25-100 keV) by means of a dual-phase Compton polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star with its unprecedented sensitivity to solar flare polarization. CUSP is a project under development as part of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. In the frame of CUSP's Phase B, which started in December 2024, a flight-representative prototype of the Compton polarimeter has been developed and characterized with hard X-ray sources in the laboratory. This prototype consists of a 4$\times$4 central matrix of plastic scintillator bars surrounded by 4 strips of 8 elongated GAGG scintillators, respectively coupled to a multi-anode photomultiplier tube and arrays of avalanche photodiodes. These sensors are read out by custom front-end electronics based on MAROC-3A and SKIROC-2A ASICs with a Xilinx Artix 7 FPGA. The plastic scintillators act as scatterers, while the GAGG bars fully absorb the scattered photons. Coincident plastic-GAGG events allow for reconstructing the Compton scattering direction, whose distribution allows for inferring the polarization parameters of the source. We report here the measured performance of the polarimeter prototype using well-known radioactive isotopes and X-ray tubes, allowing us to assess the performance of our polarimeter prototype over the full 25-100 keV energy range.

astro-ph.IM↗

arXiv2026

Spectral performance of single-channel plastic and GAGG scintillator bars of the CUbesat Solar Polarimeter (CUSP)

Our Sun is the closest X-ray astrophysical source to Earth. As such, it makes a formidable case study to better understand astrophysical processes. Solar flares are in particular very interesting as they are linked to coronal mass ejections as well as magnetic field reconnection sites in the solar atmosphere. Flares can therefore provide insightful information on the physical processes at play on their production sites, but also on the emission and acceleration of energetic charged particles towards our planet, making it a formidable forecasting tool for space weather. While solar flares are critical to understanding magnetic reconnection and particle acceleration, their hard X-ray polarization -- key to distinguishing between competing theoretical models -- remains poorly constrained by existing observations. To address this, we present the CUbesat Solar Polarimeter (CUSP), a mission under development to perform solar flare polarimetry in the 25-100 keV energy range. CUSP consists of a 6U-XL platform hosting a dual-phase Compton polarimeter. The polarimeter is made of a central assembly of four 4x4 arrays of plastic scintillators, each coupled to multi-anode photomultiplier tubes, surrounded by four strips of eight elongated GAGG scintillator bars coupled to avalanche photodiodes. Both types of sensors from Hamamatsu are respectively read out by the MAROC-3A and SKIROC-2A ASICs from Weeroc. In this manuscript, we present the preliminary spectral performances of single plastic and GAGG channels measured in the laboratory using development boards of the ASICs foreseen for the flight model.

astro-ph.IM↗

arXiv2025

Solar Flare Hard X-ray Polarimetry with the CUbesat Solar Polarimeter (CUSP) mission

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission planned for a launch in low-Earth orbit and aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. It is undergoing a 12-month Phase B that started in December 2024. The Compton polarimeter on board CUSP is composed of two acquisition chains based on plastic scintillators read out by Multi-Anode PhotoMultiplier Tubes for the scatterer part and GAGG crystals coupled to Avalanche PhotoDiodes for the absorbers. An event coincident between the two readout schemes will lead to a measurement of the incoming X-ray's azimuthal scattering angle, linked to the polarization of the solar flare in a statistical manner. The current status of the CUSP mission design, mission analysis, and payload scientific performance will be reported. The latter will be discussed based on preliminary laboratory results obtained in parallel with Geant4 simulations.

astro-ph.SR↗

arXiv2025

The multi-physics analysis, design and testing of CUSP, a CubeSat mission for space weather and solar flares x-ray polarimetry

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed at developing new CubeSat missions. As part of CUSP's Phase B study, which began in December 2024 and will last one year, we present the current development status of the design solutions adopted for the mission's most critical multi-physics design drivers. These solutions have been formulated and applied to demonstrate compliance with system requirements at both the spacecraft and platform levels. In particular, we describe the mechanical design of each structural component, the results of static, dynamic finite element analyses, and a proposal for topological optimization of the interface between the platform and payload and some fixture for test, and the preliminary environmental testing campaign (e.g., vibration, shock) that will be carried out on a mechanical demonstrator.

astro-ph.IM↗

arXiv2025

The CUbesat Solar Polarimeter (CUSP): mission overview II

The CUbesat Solar Polarimeter (CUSP) project is an Earth-orbiting CubeSat mission designed to measure the linear polarization of solar flares in the hard X-ray band using a Compton scattering polarimeter. CUSP will enable the study of magnetic reconnection and particle acceleration within the Sun's flaring magnetic structures. This project is being developed within the framework of the Italian Space Agency's Alcor Program, which aims to foster new CubeSat missions. CUSP entered its Phase B in December 2024, a phase scheduled to last 12 months. This paper reports on the current status of the CUSP mission design, mission analysis, and payload scientific performance.

astro-ph.SR↗

arXiv2025

CUbesat Solar Polarimeter (CUSP) Sensitivity Estimation and Performance Optimization using Geant4

The CUbesat Solar Polarimeter (CUSP) aims to measure the linear polarization of solar flares in the 25-100 keV X-ray band using a Compton scattering polarimeter. CUSP will allow us to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star by providing high-sensitivity polarization measurements. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop innovative CubeSat technologies and missions. As part of CUSPs Phase B study, which began in December 2024 and will continue for one year, we present the development status of the Geant4 based simulator to accurately simulate the detectors response and initial results on the sensitivity of the instrument. Geant4 Monte Carlo simulation is used to assess the physical interactions of the source photons with the detector and the passive materials. We implemented a detailed CUSP Mass Model within Geant4 to simulate and estimate the instruments sensitivity, correcting the geometric effects of the instrument. We also evaluated the effect of backscattering shielding on the sensitivity to optimize the mass model of the instrument.

astro-ph.SR↗

arXiv2025

Prototype Development and Calibration of the CUbesat Solar Polarimeter (CUSP)

The space-based CUbesat Solar Polarimeter (CUSP) mission aims to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star with its unprecedented sensitivity to solar flare polarization. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. It has been proposed as a constellation of a two Cubesat mission to monitor the Sun for Space Weather, and will proceed with a single-satellite asset in its baseline implementation. In the frame of CUSP's Phase B study, that started in December 2024 for a 1-year period, we present the development status of this dual-phase polarimeter. Preliminary laboratory results using two chains of acquisition will be discussed. The first chain of acquisition, based on the Hamamatsu R7600 multi-anode photomultiplier tubes coupled to plastic scintillator bars and read out by the MAROC-3A ASIC, is used to detect the Compton scattering of incoming photons. On the other hand, GAGG crystals coupled to avalanche photo-diodes with a readout based on the SKIROC-2A ASIC are used to absorb the scattered photons. By reconstructing the azimuthal scattering direction for many incoming photons, one can infer the linear polarization degree and angle of the source. We will discuss the calibration results obtained with our prototype detector by using well-known radioactive isotopes, allowing us to assess the performances of our detector over the full 25-100 keV energy range.

astro-ph.IM↗

arXiv2025

Study of the HV power supply modules for the CUbesat Solar Polarimeter (CUSP)

The CUbesat Solar Polarimeter (CUSP) project is a CubeSat mission orbiting the Earth aimed to measure the linear polarization of solar flares in the hard X-ray band by means of a Compton scattering polarimeter. CUSP will allow to study the magnetic reconnection and particle acceleration in the flaring magnetic structures of our star. CUSP is a project in the framework of the Alcor Program of the Italian Space Agency aimed to develop new CubeSat missions. CUSP undergoing the Phase B started in December 2024 that will last for 12 month. The Compton polarimeter of the CUSP payload performs coincidence measurements between plastic scintilaltors and GaGG(Ce) crystals to derive the polarization of X-rays. These sensors are readout by Multi Anode Photomultiplier Tubes (MAPMTs) and Avalanche Photodiodes (APDs) respectively. Both sensors need an HV power supply up to -1~kV (for the MAPMT) and +500~V (for the APD). We tested precision regulated High Voltage DC/DC Converters by HVM Technology Inc. with Sub-Miniature Case Size ($0.85''\times0.85''\times0.60''$) of the SMHV series. These modules are compact and suited for CubeSat missions.

astro-ph.IM↗