arXiv subjects

Amitava Ghosh

Publications and source records attributed to Amitava Ghosh.

32 records · Page 2Linked to original sources

arXiv2016

Investigation of Prediction Accuracy, Sensitivity, and Parameter Stability of Large-Scale Propagation Path Loss Models for 5G Wireless Communications

This paper compares three candidate large-scale propagation path loss models for use over the entire microwave and millimeter-wave (mmWave) radio spectrum: the alpha-beta-gamma (ABG) model, the close-in (CI) free space reference distance model, and the CI model with a frequency-weighted path loss exponent (CIF). Each of these models have been recently studied for use in standards bodies such as 3GPP, and for use in the design of fifth generation (5G) wireless systems in urban macrocell, urban microcell, and indoor office and shopping mall scenarios. Here we compare the accuracy and sensitivity of these models using measured data from 30 propagation measurement datasets from 2 GHz to 73 GHz over distances ranging from 4 m to 1238 m. A series of sensitivity analyses of the three models show that the physically-based two-parameter CI model and three-parameter CIF model offer computational simplicity, have very similar goodness of fit (i.e., the shadow fading standard deviation), exhibit more stable model parameter behavior across frequencies and distances, and yield smaller prediction error in sensitivity testing across distances and frequencies, when compared to the four-parameter ABG model. Results show the CI model with a 1 m close-in reference distance is suitable for outdoor environments, while the CIF model is more appropriate for indoor modeling. The CI and CIF models are easily implemented in existing 3GPP models by making a very subtle modification -- by replacing a floating non-physically based constant with a frequency-dependent constant that represents free space path loss in the first meter of propagation.

cs.IT↗

arXiv2016

Indoor 5G 3GPP-like Channel Models for Office and Shopping Mall Environments

Future mobile communications systems are likely to be very different to those of today with new service innovations driven by increasing data traffic demand, increasing processing power of smart devices and new innovative applications. To meet these service demands the telecommunications industry is converging on a common set of 5G requirements which includes network speeds as high as 10 Gbps, cell edge rate greater than 100 Mbps, and latency of less than 1 msec. To reach these 5G requirements the industry is looking at new spectrum bands in the range up to 100 GHz where there is spectrum availability for wide bandwidth channels. For the development of new 5G systems to operate in bands up to 100 GHz there is a need for accurate radio propagation models which are not addressed by existing channel models developed for bands below 6 GHz. This paper presents a preliminary overview of the 5G channel models for bands up to 100 GHz in indoor offices and shopping malls, derived from extensive measurements across a multitude of bands. These studies have found some extensibility of the existing 3GPP models to the higher frequency bands up to 100 GHz. The measurements indicate that the smaller wavelengths introduce an increased sensitivity of the propagation models to the scale of the environment and show some frequency dependence of the path loss as well as increased occurrence of blockage. Further, the penetration loss is highly dependent on the material and tends to increase with frequency. The small-scale characteristics of the channel such as delay spread and angular spread and the multipath richness is somewhat similar over the frequency range, which is encouraging for extending the existing 3GPP models to the wider frequency range. Further work will be carried out to complete these models, but this paper presents the first steps for an initial basis for the model development.

cs.IT↗

arXiv2016

A Comparison of MIMO Techniques in Downlink Millimeter Wave Cellular Networks with Hybrid Beamforming

Large antenna arrays will be needed in future millimeter wave (mmWave) cellular networks, enabling a large number of different possible antenna architectures and multiple-input multiple-output (MIMO) techniques. It is still unclear which MIMO technique is most desirable as a function of different network parameters. This paper, therefore, compares the coverage and rate performance of hybrid beamforming enabled multi-user (MU) MIMO and single-user spatial multiplexing (SM) with single-user analog beamforming (SU-BF). A stochastic geometry model for coverage and rate analysis is proposed for MU-MIMO mmWave cellular networks, taking into account important mmWave-specific hardware constraints for hybrid analog/digital precoders and combiners, and a blockage-dependent channel model which is sparse in angular domain. The analytical results highlight the coverage, rate and power consumption tradeoffs in multiuser mmWave networks. With perfect channel state information at the transmitter and round robin scheduling, MU-MIMO is usually a better choice than SM or SU-BF in mmWave cellular networks. This observation, however, neglects any overhead due to channel acquisition or computational complexity. Incorporating the impact of such overheads, our results can be re-interpreted so as to quantify the minimum allowable efficiency of MU-MIMO to provide higher rates than SM or SU-BF.

cs.IT↗

arXiv2016

5G 3GPP-like Channel Models for Outdoor Urban Microcellular and Macrocellular Environments

For the development of new 5G systems to operate in bands up to 100 GHz, there is a need for accurate radio propagation models at these bands that currently are not addressed by existing channel models developed for bands below 6 GHz. This document presents a preliminary overview of 5G channel models for bands up to 100 GHz. These have been derived based on extensive measurement and ray tracing results across a multitude of frequencies from 6 GHz to 100 GHz, and this document describes an initial 3D channel model which includes: 1) typical deployment scenarios for urban microcells (UMi) and urban macrocells (UMa), and 2) a baseline model for incorporating path loss, shadow fading, line of sight probability, penetration and blockage models for the typical scenarios. Various processing methodologies such as clustering and antenna decoupling algorithms are also presented.

cs.IT↗

arXiv2016

Propagation Path Loss Models for 5G Urban Micro- and Macro-Cellular Scenarios

This paper presents and compares two candidate large-scale propagation path loss models, the alpha-beta-gamma (ABG) model and the close-in (CI) free space reference distance model, for the design of fifth generation (5G) wireless communication systems in urban micro- and macro-cellular scenarios. Comparisons are made using the data obtained from 20 propagation measurement campaigns or ray-tracing studies from 2 GHz to 73.5 GHz over distances ranging from 5 m to 1429 m. The results show that the one-parameter CI model has a very similar goodness of fit (i.e., the shadow fading standard deviation) in both line-of-sight and non-line-of-sight environments, while offering substantial simplicity and more stable behavior across frequencies and distances, as compared to the three-parameter ABG model. Additionally, the CI model needs only one very subtle and simple modification to the existing 3GPP floating-intercept path loss model (replacing a constant with a close-in free space reference value) in order to provide greater simulation accuracy, more simplicity, better repeatability across experiments, and higher stability across a vast range of frequencies.

cs.IT↗

arXiv2015

Adaptive Millimeter Wave Beam Alignment for Dual-Polarized MIMO Systems

Fifth generation wireless systems are expected to employ multiple antenna communication at millimeter wave (mmWave) frequencies using small cells within heterogeneous cellular networks. The high path loss of mmWave as well as physical obstructions make communication challenging. To compensate for the severe path loss, mmWave systems may employ a beam alignment algorithm that facilitates highly directional transmission by aligning the beam direction of multiple antenna arrays. This paper discusses a mmWave system employing dual-polarized antennas. First, we propose a practical soft-decision beam alignment (soft-alignment) algorithm that exploits orthogonal polarizations. By sounding the orthogonal polarizations in parallel, the equality criterion of the Welch bound for training sequences is relaxed. Second, the analog beamforming system is adapted to the directional characteristics of the mmWave link assuming a high Ricean K-factor and poor scattering environment. The soft-algorithm enables the mmWave system to align innumerable narrow beams to channel subspace in an attempt to effectively scan the mmWave channel. Thirds, we propose a method to efficiently adapt the number of channel sounding observations to the specific channel environment based on an approximate probability of beam misalignment. Simulation results show the proposed soft-alignment algorithm with adaptive sounding time effectively scans the channel subspace of a mobile user by exploiting polarization diversity.

cs.IT↗

arXiv2015

Tractable Model for Rate in Self-Backhauled Millimeter Wave Cellular Networks

Millimeter wave (mmW) cellular systems will require high gain directional antennas and dense base station (BS) deployments to overcome high near field path loss and poor diffraction. As a desirable side effect, high gain antennas provide interference isolation, providing an opportunity to incorporate self-backhauling--BSs backhauling among themselves in a mesh architecture without significant loss in throughput--to enable the requisite large BS densities. The use of directional antennas and resource sharing between access and backhaul links leads to coverage and rate trends that differ significantly from conventional microwave ($μ$W) cellular systems. In this paper, we propose a general and tractable mmW cellular model capturing these key trends and characterize the associated rate distribution. The developed model and analysis is validated using actual building locations from dense urban settings and empirically-derived path loss models. The analysis shows that in sharp contrast to the interference limited nature of $μ$W cellular networks, the spectral efficiency of mmW networks (besides total rate) also increases with BS density particularly at the cell edge. Increasing the system bandwidth, although boosting median and peak rates, does not significantly influence the cell edge rate. With self-backhauling, different combinations of the wired backhaul fraction (i.e. the faction of BSs with a wired connection) and BS density are shown to guarantee the same median rate (QoS).

cs.IT↗

arXiv2015

3D Channel Model in 3GPP

Multi-antenna techniques capable of exploiting the elevation dimension are anticipated to be an important air-interface enhancement targeted to handle the expected growth in mobile traffic. In order to enable the development and evaluation of such multi-antenna techniques, the 3rd generation partnership project (3GPP) has recently developed a 3-dimensional (3D) channel model. The existing 2-dimensional (2D) channel models do not capture the elevation channel characteristics lending them insufficient for such studies. This article describes the main components of the newly developed 3D channel model and the motivations behind introducing them. One key aspect is the ability to model channels for users located on different floors of a building (at different heights). This is achieved by capturing a user height dependency in modelling some channel characteristics including pathloss, line-of-sight (LOS) probability, etc. In general this 3D channel model follows the framework of WINNERII/WINNER+ while also extending the applicability and the accuracy of the model by introducing some height and distance dependent elevation related parameters.

cs.IT↗

arXiv2014

Spectrum Sharing for Device-to-Device Communication in Cellular Networks

This paper addresses two fundamental and interrelated issues in device-to-device (D2D) enhanced cellular networks. The first issue is how D2D users should access spectrum, and we consider two choices: overlay (orthogonal spectrum between D2D and cellular UEs) and underlay (non-orthogonal). The second issue is how D2D users should choose between communicating directly or via the base station, a choice that depends on distance between the potential D2D transmitter and receiver. We propose a tractable hybrid network model where the positions of mobiles are modeled by random spatial Poisson point process, with which we present a general analytical approach that allows a unified performance evaluation for these questions. Then, we derive analytical rate expressions and apply them to optimize the two D2D spectrum sharing scenarios under a weighted proportional fair utility function. We find that as the proportion of potential D2D mobiles increases, the optimal spectrum partition in the overlay is almost invariant (when D2D mode selection threshold is large) while the optimal spectrum access factor in the underlay decreases. Further, from a coverage perspective, we reveal a tradeoff between the spectrum access factor and the D2D mode selection threshold in the underlay: as more D2D links are allowed (due to a more relaxed mode selection threshold), the network should actually make less spectrum available to them to limit their interference.

cs.IT↗

arXiv2014

Kronecker Product Correlation Model and Limited Feedback Codebook Design in a 3D Channel Model

A 2D antenna array introduces a new level of control and additional degrees of freedom in multiple-input-multiple-output (MIMO) systems particularly for the so-called "massive MIMO" systems. To accurately assess the performance gains of these large arrays, existing azimuth-only channel models have been extended to handle 3D channels by modeling both the elevation and azimuth dimensions. In this paper, we study the channel correlation matrix of a generic ray-based 3D channel model, and our analysis and simulation results demonstrate that the 3D correlation matrix can be well approximated by a Kronecker production of azimuth and elevation correlations. This finding lays the theoretical support for the usage of a product codebook for reduced complexity feedback from the receiver to the transmitter. We also present the design of a product codebook based on Grassmannian line packing.

cs.IT↗

arXiv2013

An Overview on 3GPP Device-to-Device Proximity Services

Device-to-device (D2D) communication will likely be added to LTE in 3GPP Release 12. In principle, exploiting direct communication between nearby mobile devices will improve spectrum utilization, overall throughput, and energy consumption, while enabling new peer-to-peer and location-based applications and services. D2D-enabled LTE devices can also become competitive for fallback public safety networks, that must function when cellular networks are not available, or fail. Introducing D2D poses many challenges and risks to the long-standing cellular architecture, which is centered around the base station. We provide an overview on D2D standardization activities in 3GPP, identify outstanding technical challenges, draw lessons from initial evaluation studies, and summarize "best practices" in the design of a D2D-enabled air interface for LTE-based cellular networks.

cs.NI↗

arXiv2013

Modeling, Analysis and Optimization of Multicast Device-to-Device Transmission

Multicast device-to-device (D2D) transmission is important for applications like local file transfer in commercial networks and is also a required feature in public safety networks. In this paper we propose a tractable baseline multicast D2D model, and use it to analyze important multicast metrics like the coverage probability, mean number of covered receivers and throughput. In addition, we examine how the multicast performance would be affected by certain factors like mobility and network assistance. Take the mean number of covered receivers as an example. We find that simple repetitive transmissions help but the gain quickly diminishes as the repetition time increases. Meanwhile, mobility and network assistance (i.e. allowing the network to relay the multicast signals) can help cover more receivers. We also explore how to optimize multicasting, e.g. by choosing the optimal multicast rate and the optimal number of retransmission times.

cs.IT↗

arXiv2013

Millimeter Wave Beamforming for Wireless Backhaul and Access in Small Cell Networks

Recently, there has been considerable interest in new tiered network cellular architectures, which would likely use many more cell sites than found today. Two major challenges will be i) providing backhaul to all of these cells and ii) finding efficient techniques to leverage higher frequency bands for mobile access and backhaul. This paper proposes the use of outdoor millimeter wave communications for backhaul networking between cells and mobile access within a cell. To overcome the outdoor impairments found in millimeter wave propagation, this paper studies beamforming using large arrays. However, such systems will require narrow beams, increasing sensitivity to movement caused by pole sway and other environmental concerns. To overcome this, we propose an efficient beam alignment technique using adaptive subspace sampling and hierarchical beam codebooks. A wind sway analysis is presented to establish a notion of beam coherence time. This highlights a previously unexplored tradeoff between array size and wind-induced movement. Generally, it is not possible to use larger arrays without risking a corresponding performance loss from wind-induced beam misalignment. The performance of the proposed alignment technique is analyzed and compared with other search and alignment methods. The results show significant performance improvement with reduced search time.

cs.IT↗

arXiv2013

Modeling, Analysis and Design for Carrier Aggregation in Heterogeneous Cellular Networks

Carrier aggregation (CA) and small cells are two distinct features of next-generation cellular networks. Cellular networks with small cells take on a very heterogeneous characteristic, and are often referred to as HetNets. In this paper, we introduce a load-aware model for CA-enabled \textit{multi}-band HetNets. Under this model, the impact of biasing can be more appropriately characterized; for example, it is observed that with large enough biasing, the spectral efficiency of small cells may increase while its counterpart in a fully-loaded model always decreases. Further, our analysis reveals that the peak data rate does not depend on the base station density and transmit powers; this strongly motivates other approaches e.g. CA to increase the peak data rate. Last but not least, different band deployment configurations are studied and compared. We find that with large enough small cell density, spatial reuse with small cells outperforms adding more spectrum for increasing user rate. More generally, universal cochannel deployment typically yields the largest rate; and thus a capacity loss exists in orthogonal deployment. This performance gap can be reduced by appropriately tuning the HetNet coverage distribution (e.g. by optimizing biasing factors).

cs.IT↗