Searcharxiv⌕ Search

arXiv subjects

Andreas Tünnermann

Publications and source records attributed to Andreas Tünnermann.

At least 37 records · Page 2Linked to original sources

Quantum-limited measurements of intensity noise levels in Yb-doped fiber amplifiers

We investigate the frequency-resolved intensity noise spectrum of an Yb-doped fiber amplifier down to the fundamental limit of quantum noise. We focus on the kHz and low MHz frequency regime with special interest in the region between 1 and 10 kHz. Intensity noise levels up to >60 dB above the shot noise limit are found, revealing great optimization potential. Additionally, two seed lasers with different noise characteristics were amplified, showing that the seed source has a significant impact and should be considered in the design of high power fiber amplifiers.

physics.optics↗

Precision manufacturing of a lightweight mirror body made by selective laser melting

This article presents a new and individual way to generate opto-mechanical components by Additive Manufacturing, embedded in an established process chain for the fabrication of metal optics. The freedom of design offered by additive techniques gives the opportunity to produce more lightweight parts with improved mechanical stability. The latter is demonstrated by simulations of several models of metal mirrors with a constant outer shape but varying mass reduction factors. The optimized lightweight mirror exhibits $63.5 \%$ of mass reduction and a higher stiffness compared to conventional designs, but it is not manufacturable by cutting techniques. Utilizing Selective Laser Melting instead, a demonstrator of the mentioned topological non-trivial design is manufactured out of AlSi12 alloy powder. It is further shown that -- like in case of a traditional manufactured mirror substrate -- optical quality can be achieved by diamond turning, electroless nickel plating, and polishing techniques, which finally results in $< 150$~nm peak-to-valley shape deviation and a roughness of $< 1$~nm rms in a measurement area of $140 \times 110$ $μ$m${}^2$. Negative implications from the additive manufacturing are shown to be negligible. Further it is shown that surface form is maintained over a two year storage period under ambient conditions.

physics.app-ph↗

Velocity- and pointing-error measurements of a 300 000 r/min self-bearing permanent-magnet motor for optical applications

Compact, ultra-high-speed self-bearing permanent-magnet motors enable a wide scope of applications including an increasing number of optical ones. For implementation in an optical setup the rotors have to satisfy high demands regarding their velocity and pointing errors. Only a restricted number of measurements of these parameters exist and only at relatively low velocities. This manuscript presents the measurement of the velocity and pointing errors at rotation frequencies up to 5 kHz. The acquired data allows to identify the rotor drive as the main source of velocity variations with fast fluctuations of up to 3.4 ns (RMS) and slow drifts of 23 ns (RMS) over ~120 revolutions at 5 kHz in vacuum. At the same rotation frequency the pointing fluctuated by 12 $μ$rad (RMS) and 33 $μ$rad (peak-to-peak) over ~10000 roundtrips. To our best knowledge this states the first measurement of velocity and pointing errors at multi-kHz rotation frequencies and will allow potential adopters to evaluate the feasibility of such rotor drives for their application.

physics.ins-det↗

Materials Pushing the Application Limits of Wire Grid Polarizers further into the Deep Ultraviolet Spectral Range

Wire grid polarizers (WGPs), periodic nano-optical meta-surfaces, are convenient polarizing elements for many optical applications. However, they are still inadequate in the deep ultraviolet spectral range. We show that to achieve high performance ultraviolet WGPs a material with large absolute value of the complex permittivity and extinction coefficient at the wavelength of interest has to be utilized. This requirement is compared to refractive index models considering intraband and interband absorption processes. We elucidate why the extinction ratio of metallic WGPs intrinsically humble in the deep ultraviolet, whereas wide bandgap semiconductors are superior material candidates in this spectral range. To demonstrate this, we present the design, fabrication and optical characterization of a titanium dioxide WGP. At a wavelength of 193 nm an unprecedented extinction ratio of 384 and a transmittance of 10 % is achieved.

physics.optics↗

Table-Top Milliwatt-Class Extreme Ultraviolet High Harmonic Light Source

Extreme ultraviolet (XUV) lasers are essential for the investigation of fundamental physics. Especially high repetition rate, high photon flux sources are of major interest for reducing acquisition times and improving signal to noise ratios in a plethora of applications. Here, an XUV source based on cascaded frequency conversion is presented, which delivers due to the drastic better single atom response for short wavelength drivers, an average output power of (832 +- 204) μW at 21.7 eV. This is the highest average power produced by any HHG source in this spectral range surpassing precious demonstrations by more than a factor of four. Furthermore, a narrow-band harmonic at 26.6 eV with a relative energy bandwidth of only ΔE/E= 1.8 x 10E-3 has been generated, which is of high interest for high precision spectroscopy experiments.

physics.optics↗

High-repetition-rate and high-photon-flux 70 eV high-harmonic source for coincidence ion imaging of gas-phase molecules

Unraveling and controlling chemical dynamics requires techniques to image structural changes of molecules with femtosecond temporal and picometer spatial resolution. Ultrashort-pulse x-ray free-electron lasers have significantly advanced the field by enabling advanced pump-probe schemes. There is an increasing interest in using table-top photon sources enabled by high-harmonic generation of ultrashort-pulse lasers for such studies. We present a novel high-harmonic source driven by a 100 kHz fiber laser system, which delivers 10$^{11}$ photons/s in a single 1.3 eV bandwidth harmonic at 68.6 eV. The combination of record-high photon flux and high repetition rate paves the way for time-resolved studies of the dissociation dynamics of inner-shell ionized molecules in a coincidence detection scheme. First coincidence measurements on CH$_3$I are shown and it is outlined how the anticipated advancement of fiber laser technology and improved sample delivery will, in the next step, allow pump-probe studies of ultrafast molecular dynamics with table-top XUV-photon sources. These table-top sources can provide significantly higher repetition rates than the currently operating free-electron lasers and they offer very high temporal resolution due to the intrinsically small timing jitter between pump and probe pulses.

physics.atom-ph↗

Cancellation of lateral displacement noise of 3-port gratings for coupling light to cavities

Reflection gratings enable light coupling to optical cavities without transmission through substrates. Gratings that have three ports and are mounted in second-order Littrow configuration even allow the coupling to high-finesse cavities using low diffraction efficiencies. In contrast to conventional transmissive cavity couplers, however, the phase of the diffracted light depends on the lateral position of the grating, which introduces an additional noise coupling. Here we experimentally demonstrate that this kind of noise cancels out once both diffracted output ports of the grating are combined. We achieve the same signal-to-shot-noise ratio as for a conventional coupler. From this perspective, 3-port grating couplers in second-order Littrow configuration remain a valuable approach to reducing optical absorption of cavity coupler substrates in future gravitational wave detectors.

physics.optics↗

High photon flux table-top coherent extreme ultraviolet source

High harmonic generation (HHG) enables extreme ultraviolet radiation with table-top setups. Its exceptional properties, such as coherence and (sub)-femtosecond pulse durations, have led to a diversity of applications. Some of these require a high photon flux and megahertz repetition rates, e.g. to avoid space charge effects in photoelectron spectroscopy. To date this has only been achieved with enhancement cavities. Here, we establish a novel route towards powerful HHG sources. By achieving phase-matched HHG of a megahertz fibre laser we generate a broad plateau (25 eV - 40 eV) of strong harmonics, each containing more than $10^{12}$ photons/s, which constitutes an increase by more than one order of magnitude in that wavelength range. The strongest harmonic (H25, 30 eV) has an average power of 143 $μ$W ($3\cdot10^{13}$ photons/s). This concept will greatly advance and facilitate applications in photoelectron or coincidence spectroscopy, coherent diffractive imaging or (multidimensional) surface science.

physics.optics↗

Enhancing narrowband high order harmonic generation by Fano resonances

Resonances in the photo-absorption spectrum of the generating medium can modify the spectrum of high order harmonics. In particular, window-type Fano resonances can reduce photo-absorption within a narrow spectral region and, consequently, lead to an enhanced emission of high-order harmonics in absorption-limited generation conditions. For high harmonic generation in argon it is shown that the 3s3p6 np 1P1 window resonances (n=4,5,6) give rise to enhanced photon yield. In particular, the 3s3p6 4p 1P1 resonance at 26.6 eV allows a relative enhancement up to a factor of 30 compared to the characteristic photon emission of the neighboring harmonic order. This enhanced, spectrally isolated and coherent photon emission line has a relative energy bandwidth of only ΔE/E=3*10-3. Therefore, it might be directly applied for precision spectroscopy or coherent diffractive imaging without the need of additional spectral filtering. The presented mechanism can be employed for tailoring and controlling the high harmonic emission of manifold target materials.

physics.optics↗

Calculation of thermal noise in grating reflectors

Grating reflectors have been repeatedly discussed to improve the noise performance of metrological applications due to the reduction or absence of any coating material. So far, however, no quantitative estimate on the thermal noise of these reflective structures exists. In this work we present a theoretical calculation of a grating reflector's noise. We further apply it to a proposed 3rd generation gravitational wave detector. Depending on the grating geometry, the grating material and the temperature we obtain a thermal noise decrease by up to a factor of ten compared to conventional dielectric mirrors. Thus the use of grating reflectors can substantially improve the noise performance in metrological applications.

gr-qc↗

Strain-induced pseudomagnetic field and Landau levels in photonic structures

Magnetic effects at optical frequencies are notoriously weak. This is evidenced by the fact that the magnetic permeability of nearly all materials is unity in the optical frequency range, and that magneto-optical devices (such as Faraday isolators) must be large in order to allow for a sufficiently strong effect. In graphene, however, it has been shown that inhomogeneous strains can induce 'pseudomagnetic fields' that behave very similarly to real fields. Here, we show experimentally and theoretically that, by properly structuring a dielectric lattice, it is possible to induce a pseudomagnetic field at optical frequencies in a photonic lattice, where the propagation dynamics is equivalent to the evolution of an electronic wavepacket in graphene. To our knowledge, this is the first realization of a pseudomagnetic field in optics. The induced field gives rise to multiple photonic Landau levels (singularities in the density of states) separated by band gaps. We show experimentally and numerically that the gaps between these Landau levels give rise to transverse confinement of the optical modes. The use of strain allows for the exploration of magnetic effects in a non-resonant way that would be otherwise inaccessible in optics. Employing inhomogeneous strain to induce pseudomagnetism suggests the possibility that aperiodic photonic crystal structures can achieve greater field-enhancement and slow-light effects than periodic structures via the high density-of-states at Landau levels. Generalizing these concepts to other systems beyond optics, for example with matter waves in optical potentials, offers new intriguing physics that is fundamentally different from that in purely periodic structures.

cond-mat.mes-hall↗

Expansion of a wave-packet in lattices with disorder and nonlinearity

We show, theoretically and experimentally, the counterintuitive result that an increase of disorder can result in an enhanced spreading of an initially localized excitation. Moreover, we find that adding a focusing nonlinearity facilitates the expansion of the wave-packet even further by increasing its effective size. We find a clear transition between between the regions of enhanced spreading (weak disorder) and localization (strong localization) described by a "diffusion peak".

physics.optics↗

Biphoton generation in quadratic waveguide arrays: A classical optical simulation

Quantum entanglement, the non-separability of a multipartite wave function, became essential in understanding the non-locality of quantum mechanics. In optics, this non-locality can be demonstrated on impressively large length scales, as photons travel with the speed of light and interact only weakly with their environment. With the discovery of spontaneous parametric down-conversion (SPDC) in nonlinear crystals, an efficient source for entangled photon pairs, so-called biphotons, became available. It has recently been shown that SPDC can also be implemented in nonlinear arrays of evanescently coupled waveguides which allows the generation and the investigation of correlated quantum walks of such biphotons in an integrated device. Here, we analytically and experimentally demonstrate that the biphoton degrees of freedom are entailed in an additional spatial dimension, therefore the SPDC and the subsequent quantum random walk in one-dimensional (1D) arrays can be simulated through classical optical beam propagation in a two-dimensional (2D) photonic lattice. Thereby, the output intensity images directly represent the biphoton correlations and exhibit a clear violation of a Bell-type inequality.

physics.optics↗

Diffractively coupled Fabry-Perot resonator with power-recycling

We demonstrate the optical coupling of two cavities without light transmission through a substrate. Compared to a conventional coupling component, that is a partially transmissive mirror, an all-reflective coupler avoids light absorption in the substrate and therefore associated thermal problems, and even allows the use of opaque materials with possibly favourable mechanical and thermal properties. Recently, the all-reflective coupling of two cavities with a low-efficiency 3-port diffraction grating was theoretically investigated. Such a grating has an additional (a third) port. However, it was shown that the additional port does not necessarily decrease the bandwidth of the coupled cavities. Such an all-reflective scheme for cavity coupling is of interest in the field of gravitational wave detection. In such detectors light that is resonantly enhanced inside the so-called power-recycling cavity is coupled to (kilometre-scale) Fabry-Perot resonators representing the arms of a Michelson interferometer. In order to achieve a high sensitivity over a broad spectrum, the Fabry-Perot resonators need to have a high bandwidth for a given (high) power build-up. We realized such an all-reflective coupling in a table-top experiment. Our findings are in full agreement with the theoretical model incorporating the characteristics of the 3-port grating used, and therefore encourage the application of all-reflective cavity couplers in future gravitational wave detectors.

physics.optics↗

Waveguide grating mirror in a fully suspended 10 meter Fabry-Perot cavity

We report on the first demonstration of a fully suspended 10m Fabry-Perot cavity incorporating a waveguide grating as the coupling mirror. The cavity was kept on resonance by reading out the length fluctuations via the Pound-Drever-Hall method and employing feedback to the laser frequency. From the achieved finesse of 790 the grating reflectivity was determined to exceed 99.2% at the laser wavelength of 1064\,nm, which is in good agreement with rigorous simulations. Our waveguide grating design was based on tantala and fused silica and included a ~20nm thin etch stop layer made of Al2O3 that allowed us to define the grating depth accurately during the fabrication process. Demonstrating stable operation of a waveguide grating featuring high reflectivity in a suspended low-noise cavity, our work paves the way for the potential application of waveguide gratings as mirrors in high-precision interferometry, for instance in future gravitational wave observatories.

physics.optics↗

Point-by-point inscription of apodized fiber Bragg gratings

We demonstrate apodized fiber Bragg gratings inscribed with a point-by-point technique. We tailor the grating phase and coupling amplitude through precise control over the longitudinal and transverse position of each laser-inscribed modification. This method of apodization is facilitated by the highly-localized, high-contrast modifications generated by focussed IR femtosecond laser inscription. Our technique provides a simple method for the design and implementation of point-by-point fiber Bragg gratings with complex apodization profiles.

physics.optics↗

Three-Dimensional Light Bullets in Arrays of Waveguides

We report the first experimental observation of 3D-LBs, excited by femtosecond pulses in a system featuring quasi-instantaneous cubic nonlinearity and a periodic, transversally-modulated refractive index. Stringent evidence of the excitation of LBs is based on time-gated images and spectra which perfectly match our numerical simulations. Furthermore, we reveal a novel evolution mechanism forcing the LBs to follow varying dispersion/diffraction conditions, until they leave their existence range and decay.

physics.optics↗

Cladding mode coupling in highly localized fiber Bragg gratings: modal properties and transmission spectra

The spectral characteristics of a fiber Bragg grating (FBG) with a transversely inhomogeneous refractive index profile, differs con- siderably from that of a transversely uniform one. Transmission spectra of inhomogeneous and asymmetric FBGs that have been inscribed with focused ultrashort pulses with the so-called point-by-point technique are investigated. The cladding mode resonances of such FBGs can span a full octave in the spectrum and are very pronounced (deeper than 20dB). Using a coupled-mode approach, we compute the strength of resonant coupling and find that coupling into cladding modes of higher azimuthal order is very sensitive to the position of the modification in the core. Exploiting these properties allows precise control of such reflections and may lead to many new sensing applications.

physics.optics↗